Gigabyte Ga-78lmt-usb3 Manual

- 21 -
 `DRAM	Configuration
 &DCTs Mode Allows you to set memory control mode. Ganged    Sets memory control mode to single dual-channel. Unganged   Sets memory control mode to two single-channel. (Default)
 &DDR3 Timing Items Manual allows all DRAM timing control items below to be configurable. Options are: Auto (default), Manual.
 &1T/2T Command Timing Options are: Auto (default), 1T, 2T.
 &CAS# latency Options are: Auto (default), 4T~12T.
 &RAS to CAS R/W Delay Options are: Auto (default),...

- 22 -
2-3 Standard CMOS Features
********   System Voltage Optimized    ********
 &System Voltage Control Determines whether to manually set the system voltages. Auto lets the BIOS automatically set the system voltages as required. Manual allows all voltage control items below to be configurable. (Default:  Auto)
 &NorthBridge Volt Control Allows you to set the North Bridge voltage. Normal      Supplies the North Bridge voltage as required. (Default) +0.1V ~ +0.3V   The adjustable range is...

- 23 -
2-4 Advanced BIOS Features
 &IGX	Configuration The settings in this submenu are synchronous to those under the same items on the MB Intelligent Tweaker(M.I.T.) main menu.
 &Load Line Control Enables or disables Load Line control. This item allows you to adjust Vdroop at different levels. Enabling Load-Line Calibration may keep the CPU voltage more constant under light and heavy CPU load. Auto lets the BIOS automatically configure this setting. (Default: Auto)
 &AMD C1E Support Enables or disables...

- 24 -
 &AMD C6 Support (Note)
 Allows you to determine whether to let the CPU enter C6 mode in system halt state. When enabled, the CPU core frequency will be reduced during system halt state to decrease power consumption. The C6 state is a more enhanced power-saving state than C1. (Default: Enabled)\
 &Virtualization  Virtualization enhanced by Virtualization Technology will allow a platform to run multiple operating systems and applications in independent partitions. With virtualization, one com\...

- 25 -
 &Password Check Specifies whether a password is required every time the system boots, or only when you enter BIOS Setup. After configuring this item, set the password(s) under the Set Supervisor/User Password item in the BIOS Main Menu. Setup      A password is only required for entering the BIOS Setup program. (Default) System    A password is required for booting the system and for entering the BIOS Setup program.
 &HDD S.M.A.R.T. Capability Enables or disables the S.M.A.R.T. (Self...

- 26 -
 &OnChip SATA Port4/5 Type (SATA2 4/SATA2 5 connectors) This option is configurable only when OnChip SATA Type is set to RAID or AHCI. Configures the operating mode of the integrated SATA2 4~SATA2 5 connectors. IDE        Disables RAID for the SATA controller and configures the SATA controller to PATA mode. (Default) As SATA Type  The mode depends on the OnChip SATA Type settings.
 `OnChip SATA Port as ESP
 &Port0 as ESP/Port1 as ESP/Port2 as ESP/Port3 as ESP This option is configurable...

- 27 -
 &ACPI Suspend Type Specifies the ACPI sleep state when the system enters suspend. S1(POS)      Enables the system to enter the ACPI S1 (Power on Suspend) sleep state. In S1 sleep state, the system appears suspended and stays in a low power mode. The system can be resumed at any time. S3(STR)     Enables the system to enter the ACPI S3 (Suspend to RAM) sleep state (default). In S3 sleep state, the system appears to be off and consumes less power than in the S1 state. When signaled by a...

- 28 -
 &PCI1 IRQ Assignment Auto         BIOS auto-assigns IRQ to the first PCI slot. (Default) 3,4,5,7,9,10,11,12,14,15 Assigns IRQ 3,4,5,7,9,10,11,12,14,15 to the first PCI slot.
2-7	 PnP/PCI	Configurations
 &Power On By Mouse Allows the system to be turned on by a PS/2 mouse wake-up event. Note: To use this function, you need an ATX power supply providing at least 1A on the +5VSB lead. Disabled    Disables this function. (Default) Double Click Double click on left button on the...

- 29 -
2-8 PC Health StatusCMOS Setup Utility-Copyright (C) 1984-2012  Award SoftwarePC Health Status
  Hardware  Thermal Control   [Enabled] Reset Case Open Status    [Disabled] Case Opened        No Vcore             1.280V DDR3 1.5V            1.500V +12V             12.168V +3.3V              3.397V Current System  Temperature       37oC Current CPU  Temperature       37oC Current CPU F AN Speed   1264 RPM Current SYSTEM F AN Speed        0 RPM CPU Warning  Temperature   [Disabled] CPU F AN Fail...

- 30 -
2-9 Load Fail-Safe Defaults
Press  on this item and then press the  key to load the safest BIOS default settings. In case system instability occurs, you may try to load Fail-Safe defaults, which are the safest and most stable BIOS settings for the motherboard.
2-10 Load Optimized Defaults
Press  on this item and then press the  key to load the optima\
l BIOS default settings. The BIOS defaults settings help the system to operate in optimum state. Always load the Optimized defaults after updating...