GGP Italy SPA Lawn Tractor 71503777 2 Operators Manual

EN 40MAINTENANCE
6.3.3 ADJUSTMENT TO THE ENGAGEMENT AND BRAKE OF THE BLADES
When the blade disengagement lever is
operated, it also brings the blade brake
into operation which stops the blades
within few seconds.
A stretched cable and changes in the
length of the belt can impair the blades’
engagement or rotation. 
To compensate this, turn the adjuster (1)
until the correct spring length (2) is
achieved (measured from the outer ends of the springs with the blades
engaged).
6.3.4 B
RAKE ADJUSTMENT
Should...

EN 41 MAINTENANCE
When replacing the belt, take great care when using for the
first few times as engagement may be sudden until the belt is sufficiently run in.
6.4 DISMANTLING AND REPLACEMENT
6.4.1 R
EPLACING WHEELS
Stop the machine on a flat surface and put a block under a load-bearing part of
the frame on the side that the wheel is to
be changed.
The wheels are held by a snap ring (1)
which can be eased off with a screwdriv-
er.
The rear wheels are directly coupled to
the differential axle shaft and...

6.4.3 REPLACING BULBS( if fitted)
The bulbs (18W) have a bayonet fitting and are
installed in the bulb holder which can be taken out
by turning it anti-clockwise, using pliers.
6.4.4 R
EPLACING A FUSE
The machine is fitted with fuses (1) with different
capacities and functions. Specifically:
– 6.3 A (delayed) fuse (1) = protects the main and
power circuits of the electronic board. When it
blows, the machine stops and the dashboard
light switches off.
– 25 A fuse (2) = protects the battery charger cir-...

EN 43 TROUBLESHOOTING
7. TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
1.With the key on
«ON», the light
remains off
2.With the key on
«START» the light
flashes and the starter
motor does not run
3.With the key on
«START» the light
comes on but the
starter motor does not
run
4.With the key on
«START»,  the starter
motor runs, but the
engine does not run
5.Starting is difficult
or the engine runs
erraticallyThe protection of the electronic card has
cut in due to:
– badly connected battery 
– battery...

EN 44TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
6.Weak engine per-
formance during cut-
ting
7.The engine stops
but the light flashes
8.The engine stops
and the light goes off
9. The engine stops
but the light stays on
10.The blades do not
engage 
11.Uneven cutting
and ejection– forward speed too high in relation to
cutting height  (☛5.4.5)
– the safety devices cut in
The protection of the electronic card has
cut in due to:
– earthed micro-switch
– battery contains electrolyte but is not
charged
–...

EN 45 TROUBLESHOOTING
PROBLEM LIKELY CAUSE SOLUTION
12.Unusual vibrations
while working
13.With the engine
running, the machine
does not move when
the drive pedal is
pressed ( for
hydrostatic drive mod-
els)
➤
– the blades are imbalanced
– blades loose
– fixing bolts loose
– disengage lever in position  «B»
(☛4.33)– balance or replace any damaged
blades  (☛6.3.1)
– check that the blades are firmly fitted
(☛6.3.1)
– check and tighten all the fixing bolts
of the engine and frame
– put into position «A»
If...

EN 46ACCESSORIES ON REQUEST
8. ACCESSORIES ON REQUEST
1. FRONT COUNTERWEIGHTS
These improve stability at the front of the
machine, particularly when being used on ground
which is mostly sloping. 
2. TOWING HITCH
For towing a small trailer.
3. CLOTH COVER
Protects the machine from dust when not in use.
4.
CB01 MAINTENANCE BATTERY-CHARGER
This makes it possible to keep the battery in good
working order when the machine is in storage,
guaranteeing an optimum level of charge and a
longer life to the...

EN 47 SPECIFICATIONS
9. SPECIFICATIONS
1125
1690
860
1085
8551205
For mechanical drive models:
Forward speed (approximate) at
3000 min.
–1:
in 1st  .............................. 2.2 km/h
in 2nd   ........................... 3.8 km/h
in 3rd   ............................. 5.8 km/h
in 4th   ............................. 6.4 km/h
in 5th   ............................. 9.7 km/h
In Reverse   ..................... 2.8 km/h
For hydrostatic drive models:
Forward speed (at 3000 min.
–1):
in Forward   ...... from...

EN 48ALPHABETICAL INDEX
10. ALPHABETICAL INDEX
Key
Function .................................................... 4.3
Lights
Switch ........................................................ 4.5
Bulb replacement .................................... 6.4.3
Maintenance
How to carry out maintenance .... 6.2.1 - 6.2.2
Parking brake
Lever function ............................................ 4.4
Pilot lamp
Function .................................................... 4.6
Work...