Getnet Router GR-524WA User Manual

 23 Press ‘Continue’ to save the settings made and back to web management 
interface; press ‘Apply’ to save the settings and restart the router so the 
settings will take effect after it reboots. 
 
 
5.2.1.2. Password  Settings 
 
This page allows you to set the password to access the web server of the 
router. Please select the “admin (as administrator)” or “user (as user)” account 
and configure the password. 
 
 
 
When you finish, click ‘Apply Changes’.  
 
If the password you typed in ‘New...

 24 If you see the following message: 
 
 
 
It means the content in ‘Current Password’ field is wrong, please click ‘OK’ to 
go back to previous menu, and try to input current password again.  
 
If the current and new passwords are correctly entered, after you click ‘Apply’, 
you’ll be prompted to input your new password: 
 
 
 
 
Please use new password to enter web management interface again, and you 
should be able to login with new password. 
 
 
5.2.1.3. Remote  Management 
 
The Remote Access...

 25 Please click ‘System’ menu on the left of web management interface, then 
click ‘Remote Management’, and the following page will be displayed on your 
web browser: 
 
 
Parameter Description 
LAN  Check/un-check the services on the LAN column to allow/un-
allow the services access from LAN side. 
  
WAN  Check/un-check the services on the WAN column to allow/un-
allow the services access from WAN side. 
  
WAN Port  This field allows the user to specify the port of the 
corresponding to the service....

 26 Press ‘Continue’ to save the settings made and back to web management 
interface; press ‘Apply’ to save the settings made and restart the router so the 
settings will take effect after it reboots. 
 
 
5.2.1.4. SNMP 
 
Simple Network Management Protocol (SNMP) is a troubleshooting and 
management protocol that uses the UDP protocol on port 161 to communicate 
between clients and servers. The router can be managed locally or remotely 
by SNMP protocol. 
 
 
 
Parameter Description 
SNMP  Select...

 27   
System Name  Assign an administratively name for the router. 
  
System Location  The physical location of the router. 
  
System Object ID  It is the vendor object identifier. The vendor’s 
authoritative identification of the network management 
subsystem contained in the entity. 
  
Trap IP Address  Destination IP address of the SNMP trap. 
  
Community name 
(read-only) Name of the read-only community. This read-only 
community allows read operation to all objects in the 
MIB. 
  
Community...

 28 selections for the router’s WAN port, Channel, ATM Setting, ADSL Setting, 
DNS, DDNS and RIP. 
 
 
 
 
5.2.2.1. Channel  Config 
 
ADSL modem/router supports 8 ATM Permanent Virtual Channels (PVCs) at 
the most. This page is used to configure the parameters for the channel 
operation modes of your ADSL Router. 
 
Before configuring the router, please check with your ISP (Internet Service 
Provider) what kind of the service is provided such as PPPoE, PPPoA or 
RFC1483/2684. Gather the information as...

 29 Bridged Mode. 
RFC1483 Routed  VPI/VCI, VC-based/LLC-based multiplexing, IP Address, 
Subnet Mask, Gateway Address, and Domain Name 
System (DNS) IP Address (It is a fixed IP Address). 
RFC1483 MER  VPI/VCI, VC-based/LLC-based multiplexing, IP Address, 
Subnet Mask, Gateway Address, and Domain Name 
System (DNS) IP Address. 
 
 
 
Parameter Description 
VPI  VPI is a virtual path determines the way an ATM cell 
should be routed. The VPI is an 8-bit (in UNI) or 12-bit (in 
NNI) number that is included...

 30 determine its destination. The VCI is a 16-bit number that 
is included in the header of an ATM cell. The valid range 
for the VCI is 32 to 65535. Enter the VCI assigned by the 
ISP. 
  
Encapsulation  Please check with your ISP the method of multiplexing.  
  
Channel Mode  There are five kinds of channel modes you can select for 
ADSL connection. Please check with your ISP the 
method of the ADSL connection. 
  
Enable NAPT  Enable or disable NAPT. NAPT, an Internet standard that 
enables a...

 31 the connection, please click “Disconnect” button.  
 
 
  
Idle Time (ms)  “Idle Time” is set to stop the connection when the 
network traffic is not sending or receiving after an idle 
time. 
  
WAN IP Setting   
      Type Fixed IP – Set the static IP Address to the router. Please 
enter the IP Address your ISP has assigned. 
 
DHCP –  To get the IP Address from the ISP directly. 
  
      Local IP Address  Set the IP Address obtained from your ISP. 
 
      Remote IP Address Enter the remote IP...

 32 Delete Selected  If you want to delete a specific VC channel entry, check 
the ‘select’ box of the VC channel you want to delete, 
then click ‘Delete Selected’ button. 
  
Enable Auto-PVC 
Search Check the box and ‘Apply’ button to enable auto PVC 
search function. 
  
VPI  VPI is a virtual path determines the way an ATM cell 
should be routed. 
  
VCI  VCI is the label given to an ATM VC to identify it and 
determine its destination. 
  
Add/Delete  These buttons are for you to maintain the Current...