Getnet Router GR-124W User Manual

 
6 
3.1   TCP/IP Settings 
By default, the IP address of LAN interface of the GR-124W is 192.168.1.1.The 
subnet mask is 255.255.255.0. The DHCP Server is enabled.   
It is recommended you set the network adapter to be Obtain an IP address 
automatically. Your PC automatically acquires IP address, subnet mask, gateway, 
and DNS address via the GR-124W. If you know the setting of the current LAN 
interface, you can manually set the TCP/IP properties of the network adapter, so that 
your PC can...

 
7 
 
 
Step3 Double click the Internet Protocol (TCP/IP) to display the Internet 
Protocol (TCP/IP) Properties page. 
  

 
8 
 
Step4 Select Use the following IP address and enter the IP address of the 
network adapter. The IP address should belong to the IP network segment 
192.168. 1.X (X is a number between 2 and 254). 
 
 
Step5 Set subnet mask and then click the OK button to finish manual setting. 
Step6 After finishing setting, you may ping the default IP address of the 
GR-124W, to check whether the current connection between PC and the 
GR-124W is normal. Click RUN… in the lower left corner on the desktop, 
and...

 
9 
 
 
Note: 
192.168.1.1 is the default IP address of the LAN interface. If this IP address is 
changed and you need to ping the IP address of the GR-124W, you should enter the 
current IP address in the dialog box above. 
Step7 If PC can ping through the default IP address of the GR-124W and the 
following page appears, it indicates that the connection between PC and 
the GR-124W is normal. 
 
 
3.2   Introduction to PPPoE (ADSL) and DHCP (Auto 
config) 
If you want to access the Internet via the...

 
10 
In the gateway mode, GR-124W provides 5 types uplink access modes, including 
STATIC (fixed IP), DHCP (Auto config), PPPoE (ADSL), L2TP, and PPTP. For more 
details, please refer to 5.3.2 WAN. 
  The Network Connection Mode of PPPoE 
 
 
If you access the Internet by PPPoE, please do as follows: 
Step1 Connect the uplink interface of ADSL or cable modem to the ISP office end, 
and make sure that the communication between both sides is normal. Set 
your ADSL or Cable modem to be bridge mode. For...

 
11 
 
 
Step5 On the Wide Area Network (WAN) Settings page, set the WAN 
Connection Type to be PPPoE (ADSL) and enter the correct PPPoE 
username and password. After finishing setting, click the Apply button to 
start dial-up. 
 
  The Network Connection Mode of DHCP (Auto config) 
 
 
If you can access the Internet without dial-up, and ISP provides DHCP service, 
please follow the steps below to finish setting. 
Step1 Use one Ethernet cable to connect the uplink interface of router or 
gateway to the...

 
12 
automatically. If you want to manually set the TCP/IP properties, please 
refer to 3.1 TCP/IP Settings. 
Step3 Log in to the Web page of the GR-124W. Click Internet > WAN to display 
the Wide Area Network (WAN) Settings page. On this page, set WAN 
Connection Type to be DHCP (Auto config). 
 
 
Step4 After finishing settings, click the Apply button, and then GR-124W starts 
to acquire the parameters assigned by the DHCP server, such as the IP 
address, and the DNS address. 
 
3.3   Connection...

 
13 
Network Connection icon and select View Available Wireless 
Networks. 
 
 
Step2 On the Wireless Network Connection page, click Refresh network list 
and the network list will be refreshed. The default SSID of the GR-124W is 
Getnet. Choose the AP that you want to connect, and then click the 
Connect button. The default wireless security mode is Disable, and you 
can connect AP directly without the encryption key. If the GR-124W is 
encrypted, this AP is marked with a lock icon.
  

 
14 
 
 
Step3 If the GR-124W is encrypted, you need to enter the encryption key in the 
field of network key and then click the Connect button. 
 
 
Step4 If the wireless network card connects to GR-124W successfully, the 
character Connected will appear in the AP’s upper right corner.  

 
15 
 
 
Step5 If you are not sure of the SSID available, please log in to the Web page of 
AP, and view the SSID on the Basic Wireless Settings page. For more 
information about the wireless settings, please refer to 5.4 Wireless 
Settings (Gateway Mode). 
 
 
Note: 
After your wireless network card connects to AP successfully, usually, you should 
set the network adapter to be Obtain an IP address automatically. 
 
3.5   Log In to the Web Page