Gateway 450rog 450rgh User Manual

							A
281
Safety,
Regulatory, and
Legal Information
Important safety 
information
Your Gateway notebook is designed and tested to meet the latest 
standards for safety of information technology equipment. However, to 
ensure safe use of this product, it is important that the safety instructions 
marked on the product and in the documentation are followed.
WarningAlways follow these instructions to help 
guard against personal injury and damage 
to your Gateway notebook. 
						

							282
Appendix A: Safety, Regulatory, and Legal Information
www.gateway.com
Setting up your notebook
■Read and follow all instructions marked on the product and in the documentation before you 
operate your notebook. Retain all safety and operating instructions for future use.
■Do not use this product near water or a heat source such as a radiator.
■Set up the notebook on a stable work surface.
■The product should be operated only from the type of power source indicated on the rating label.
■If your notebook has a voltage selector switch, make sure that the switch is in the proper position 
for your area. The voltage selector switch is set at the factory to the correct voltage.
■Openings in the notebook case are provided for ventilation. Do not block or cover these 
openings. Make sure you provide adequate space, at least 6 inches (15 cm), around the notebook 
f o r  v e n t i l a t i o n  w h e n  y o u  s e t  u p  y o u r  w o r k  a r e a .  N e v e r  i n s e r t  o b j e c t s  o f  a n y  k i n d  i n t o  t h e  
notebook ventilation openings.
■Some products are equipped with a three-wire power cord to make sure that the product is 
properly grounded when in use. The plug on this cord will fit only into a grounding-type outlet. 
This is a safety feature. If you are unable to insert the plug into an outlet, contact an electrician 
to install the appropriate outlet.
■If you use an extension cord with this notebook, make sure that the total ampere rating on the 
products plugged into the extension cord does not exceed the extension cord ampere rating.
■If your notebook is fitted with a TV Tuner, cable, or satellite receiver card, make sure that the 
antenna or cable system is electrically grounded to provide some protection against voltage 
surges and buildup of static charges.
Care during use
■D o  n o t  w a l k  o n  t h e  p o w e r  c o r d  o r  a l l o w  a n y t h i n g  t o  r e s t  o n  i t .
■Do not spill anything on the notebook. The best way to avoid spills is to avoid eating and 
drinking near your notebook.
■Some products have a replaceable CMOS battery on the system board. There is a danger of 
explosion if the CMOS battery is replaced incorrectly. Replace the battery with the same or 
equivalent type recommended by the manufacturer. Dispose of batteries according to the 
manufacturer’s instructions.
■When the notebook is turned off, a small amount of electrical current still flows through the 
notebook. To avoid electrical shock, always unplug all power cables and modem cables from the 
wall outlets before cleaning the notebook.
■Unplug the notebook from the wall outlet and refer servicing to qualified personnel if:
■The power cord or plug is damaged.
■Liquid has been spilled into the notebook.
■The notebook does not operate properly when the operating instructions are followed.
■The notebook was dropped or the cabinet is damaged.
■The notebook performance changes. 
						

							283
Important safety information
www.gateway.com
Replacement parts and accessories
Use only replacement parts and accessories recommended by Gateway.
ImportantDo not use Gateway products in areas classified as 
hazardous locations. Such areas include patient care 
areas of medical and dental facilities, oxygen-laden 
environments, or industrial facilities.
WarningTo reduce the risk of fire, use only No. 26 AWG or larger 
telecommunications line cord. 
						

							284
Appendix A: Safety, Regulatory, and Legal Information
www.gateway.com
Regulatory compliance 
statements
Wireless Guidance
Low power, Radio transmitting type devices (radio frequency (RF) wireless communication 
devices), may be present (embedded) in your notebook system. These devices may operate in the 
2.4 GHz (i.e. 802.11B/G LAN & Bluetooth), 5.2 GHz (i.e. 802.11A LAN), and traditional cellular or 
PCS cellular bands (i.e. Cellular data modem). The following section is a general overview of 
considerations while operating a wireless device.
Additional limitations, cautions, and concerns for specific countries are listed in the specific 
country sections (or country group sections). The wireless devices in your system are only qualified 
for use in the countries identified by the Radio Approval Marks on the system rating label. If the 
country you will be using the wireless device in, is not listed, please contact your local Radio 
Approval agency for requirements. Wireless devices are closely regulated and use may not be 
allowed.
T h e  p o w e r  o u t p u t  o f  t h e  w i r e l e s s  d e v i c e  o r  d e v i c e s  t h a t  m a y  b e  e m b e d d e d  i n  y o u r  n o t e b o o k  i s  w e l l  
below the RF exposure limits as known at this time. Because the wireless devices (which may be 
embedded into your notebook) emit less energy than is allowed in radio frequency safety standards 
and recommendations, Gateway believes these devices are safe for use. Regardless of the power 
levels, care should be taken to minimize human contact during normal operation.
Measurements have been performed to show that the RF exposure is below what is considered safe 
limits; however care should be taken to make sure the user or bystanders keep the transmitter away 
from their body when the wireless device is transmitting. The transmitting antenna installed in the 
top third of the lid should be used in a manner to maintain 20cm (8 inches) from user’s or 
bystander’s bodies.
If anyone is closer than 20 cm (8 inches) to the wireless transmitter, make sure the transmitter is 
turned off. Please see “Turning your wireless Ethernet emitter on or off” on page 196 for 
instruction on turning off the transmitter.
The wireless devices installed in this system are intended to be used indoors. In some areas, use of 
these devices outdoors is prohibited.
Some circumstances require restrictions on wireless devices. Examples of common restrictions are 
listed below:
WarningRadio frequency wireless communication can interfere 
with equipment on commercial aircraft. Current aviation 
regulations require wireless devices to be turned off while 
traveling in an airplane. 802.11B (also known as wireless 
Ethernet or Wifi) and Bluetooth communication devices are 
examples of devices that provide wireless communication. 
						

							285
Regulatory compliance statements
www.gateway.com WarningIn environments where the risk of interference to other 
devices or services is harmful or perceived as harmful, the 
option to use a wireless device may be restricted or 
eliminated. Airports, Hospitals, and Oxygen or flammable 
gas laden atmospheres are limited examples where use 
of wireless devices may be restricted or eliminated. When 
in environments where you are uncertain of the sanction 
to use wireless devices, ask the applicable authority for 
authorization prior to use or turning on the wireless device.
WarningEvery country has different restrictions on the use of 
wireless devices. If your notebook is equipped with a 
wireless device, when traveling between countries with 
your notebook, check with the local Radio Approval 
authorities prior to any move or trip for any restrictions on 
the use of a wireless device in the destination country.
WarningIf your notebook came equipped with an internal 
embedded wireless device, do not operate the wireless 
device unless all covers and shields are in place and the 
notebook is fully assembled.
WarningWireless devices are not user serviceable. Do not modify 
them in any way. Modification to a wireless device will void 
the authorization to use it. Please contact Gateway for 
service.
WarningOnly use drivers approved for the country in which the 
device will be used. See the Gateway System Restoration 
Kit, or contact Gateway Technical Support for additional 
information. 
						

							286
Appendix A: Safety, Regulatory, and Legal Information
www.gateway.com
United States of America
Federal Communications Commission (FCC)
Intentional emitter per FCC Part 15
Low power, Radio transmitter type devices (radio frequency (RF) wireless communication devices), 
operating in the 2.4 GHz band and/or 5.15 – 5.35 GHz band, may be present (embedded) in your 
notebook system. This section is only applicable if these devices are present. Refer to the system 
label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in the United States of 
America if an FCC ID number is on the system label.
The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the 
body (including bystanders), for use of a wireless device near the body (this does not include 
extremities). This device should be used more than 20 cm (8 inches) from the body when wireless 
devices are on. The power output of the wireless device (or devices), which may be embedded in 
your notebook, is well below the RF exposure limits as set by the FCC.
The wireless devices installed in this system are intended to be used indoors. In some areas, use of 
these devices outdoors is prohibited.
Operation of this device is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation of the device.
Unintentional emitter per FCC Part 15
This device has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses, and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio or television reception. However, there is no guarantee 
that interference will not occur in a particular installation. If this equipment does cause 
WarningWireless devices are not user serviceable. Do not modify 
them in any way. Modification to a wireless device will void 
the authorization to use it. Contact Gateway for service.
WarningIn order to comply with FCC requirements transmitters that 
may be embedded in your notebook must not be operated 
(or co-located) in conjunction with any other transmitter or 
antenna installed in the notebook.
WarningThe transmitting device embedded in this notebook may 
not be used with any antenna other than provide with the 
notebook. 
						

							287
Regulatory compliance statements
www.gateway.com
interference to radio and television reception, which can be determined by turning the equipment 
off and on, the user is encouraged to try to correct the interference by one or more of the following 
measures:
■Reorient or relocate the receiving antenna■Increase the separation between the equipment and receiver■Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected
■Consult the dealer or an experienced radio/TV technician for help.
Compliance Accessories: The accessories associated with this equipment are: shielded video cable 
when an external monitor is connected. These accessories are required to be used in order to 
ensure compliance with FCC rules.
FCC declaration of conformity
Responsible party:
Gateway Companies, Inc.
610 Gateway Drive, North Sioux City, SD 57049
(605) 232-2000   Fax: (605) 232-2023
Product:
■Gateway 450RGH■Gateway 450ROG
This device complies with Part 15 of the FCC Rules. Operation of this product is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired operation.
CautionChanges or modifications not expressly approved by 
Gateway could void the FCC compliance and negate your 
authority to operate the product. 
						

							288
Appendix A: Safety, Regulatory, and Legal Information
www.gateway.com
Telecommunications per FCC part 68 
(applicable to products fitted with USA modems)
Your modem complies with Part 68 of the Federal Communications Commission (FCC) rules. On 
the computer or modem card is a label that contains the FCC registration number and Ringer 
Equivalence Number (REN) for this device. If requested, this information must be provided to the 
telephone company.
An FCC-compliant telephone line cord with a modular plug is required for use with this device. 
The modem is designed to be connected to the telephone network or premises wiring using a 
compatible modular jack which is Part 68-compliant. See installation instructions for details.
The Ringer Equivalence Number (REN) is used to determine the number of devices which may be 
connected to the telephone line. Excessive RENs on a telephone line may result in the devices not 
ringing in response to an incoming call. In most areas, the sum of RENs should not exceed five 
(5.0). To be certain of the number of devices that may be connected to a line, as determined by the 
total RENs, contact the local telephone company.
If this device causes harm to the telephone network, the telephone company will notify you in 
advance that temporary discontinuance of service may be required. The telephone company may 
request that you disconnect the equipment until the problem is resolved.
The telephone company may make changes in its facilities, equipment, operations, or procedures 
that could affect the operation of this equipment. If this happens, the telephone company will 
provide advance notice in order for you to make necessary modifications to maintain 
uninterrupted service.
This equipment cannot be used on telephone company-provided coin service. Connection to party 
line service is subject to state tariffs. Contact the state public utility commission or public service 
commission for information.
When programming or making test calls to emergency numbers:
■Remain on the line and briefly explain to the dispatcher the reason for the call.■Perform such activities in the off-peak hours such as early morning or late evenings.
The United States Telephone Consumer Protection Act of 1991 makes it unlawful for any person to 
use a computer or other electronic device to send any message via a telephone fax machine unless 
such message clearly contains, in a margin at the top or bottom of each transmitted page or on the 
first page of the transmission, the date and time it is sent, an identification of the business, other 
entity, or other individual sending the message, and the telephone number of the sending 
machine or such business, other entity, or individual. Refer to your fax communication software 
documentation for details on how to comply with the fax-branding requirement. 
						

							289
Regulatory compliance statements
www.gateway.com
Canada
Industry Canada (IC)
Intentional emitter per RSS 210
Low power, Radio transmitter type devices (radio frequency (RF) wireless communication devices), 
operating in the 2.4 GHz band and/or 5.15 – 5.35 GHz band, may be present (embedded) in your 
notebook system. This section is only applicable if these devices are present. Refer to the system 
label to verify the presence of wireless devices.
Wireless devices that may be in your system are only qualified for use in Canada if an Industry 
Canada ID number is on the system label.
As a general guideline, a separation of 20 cm (8inches) between the wireless device and the body 
(including bystanders), for use of a wireless device near the body (this does not include extremities) 
i s  t y p i c a l .  T h i s  d e v i c e  s h o u l d  b e  u s e d  m o r e  t h a n  2 0 c m  ( 8 i n c h e s )  f r o m  t h e  b o d y  w h e n  w i r e l e s s  
devices are on. The power output of the wireless device (or devices), which may be embedded in 
your notebook, is well below the RF exposure limits as set by Industry Canada. 
Operation of this device is subject to the following two conditions: (1) This device may not cause 
harmful interference, and (2) this device must accept any interference received, including 
interference that may cause undesired operation of the device.
WarningTo prevent radio interference to licensed service or 
co-channel Mobile Satellite systems, this device is 
intended to be operated indoors and away from windows 
to provide maximum shielding. Equipment (or its transmit 
antenna) that is installed outdoors is subject to licensing.
WarningWireless devices are not user serviceable. Do not modify 
them in any way. Modification to a wireless device will void 
the authorization to use it. Contact Gateway for service.
WarningThe transmitting device embedded in this notebook may 
not be used with any antenna other than provide with the 
notebook.
WarningThe 802.11A radio LAN your notebook may have been 
equipped with operates in the same frequency range as 
high power radar, which has priority use, and may damage 
the radio LAN if both are present and being used in the 
same area. 
						

							290
Appendix A: Safety, Regulatory, and Legal Information
www.gateway.com
Unintentional emitter per ICES-003
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital 
apparatus as set out in the radio interference regulations of Industry Canada.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites 
applicables aux appareils numériques de Classe B prescrites dans le règlement sur le brouillage 
radioélectrique édicté par Industrie Canada.
Telecommunications per Industry Canada CS-03
(for products fitted with an IC-compliant modem)
The Industry Canada label identifies certified equipment. This certification means that the 
equipment meets certain telecommunications network protective, operation, and safety 
requirements. The Department does not guarantee the equipment will operate to the users’ 
satisfaction.
Before installing this equipment, users should make sure that it is permissible to be connected to 
the facilities of the local telecommunications company. The equipment must also be installed 
using an acceptable method of connection. In some cases, the inside wiring associated with a 
single-line individual service may be extended by means of a certified connector assembly. The 
customer should be aware that compliance with the above conditions may not prevent 
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility 
designated by the supplier. Any repairs or alterations made by the user to this equipment, or 
equipment malfunctions, may give the telecommunications company cause to request the user to 
disconnect the equipment.
Users should make sure, for their own protection, that the electrical ground connections of the 
power utility, telephone lines, and internal metallic water pipe system, if present, are connected 
together. This precaution may be particularly important in rural areas.
The Ringer Equivalence Number ( R E N )  a s s i g n e d  t o  e a c h  t e r m i n a l  d e v i c e  p r o v i d e s  a n  i n d i c a t i o n  o f  
the maximum number of terminals allowed to be connected to a telephone interface. The 
termination on an interface may consist of any combination of devices subject only to the 
requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
WarningTo avoid electrical shock or equipment malfunction do not 
attempt to make electrical ground connections by yourself. 
Contact the appropriate inspection authority or an 
electrician, as appropriate.