Funai LT8 M40BB User Manual

							12EN
OPERATIONS
Watching a TV Programme
To select a channel
Press [PROG.K / L] (control panel) or [/] 
(remote control) repeatedly to select your desired channel.
or
Press [the Number buttons] to enter a channel number then 
[OK] for quicker access.
 If you want to select the channel 24 without pressing [OK], 
press [2] first, then press [4] within 3 seconds.
To adjust the volume
Press [VOL.X / Y] (control panel) or [+/–] (remote 
control) to adjust the audio volume.
 You can see the volume bar while adjusting the volume.
Press [ (mute)] to turn on or off the sound right away.
 You can recover the original volume by pressing [ (mute)] 
again or [+/–].
Sleep Timer
You can set the unit to be turned off automatically after a set time 
period (from 10 to 120 minutes).
1)Press [SLEEP].
 Sleep timer display will appear.
2)Press [SLEEP] repeatedly to change the sleep time period.
 Between Off and 60 minutes, the interval of time is 10 
minutes. After 60 minutes, the timer increases by 30 
minutes until Off.
To cancel the sleep timer
1)Press [SLEEP].
 Sleep timer display will appear.
2)Press [SLEEP] repeatedly until “Sleep Off ” appears.
Switching the Input Mode
You can switch the input mode to TV mode or external input 
mode.
1)Press [INPUT].
 “Select Input” menu will appear.
2)Press [K / L] to select the input mode you want, then press 
[OK].
Note:If you disconnect the unit from the AC outlet or if a 
power failure occurs, the sleep timer will be cancelled.
DTVATV
30Volume
DTVATV
Sleepmin. 10
Sleep Off
Note: To watch TV, select “TV”.
 To use the video or S-VIDEO input jack on the unit, 
select “VIDEO”.
 To use the COMPONENT (Y/Pb/Pr) input jack on 
the unit, select “COMPONENT”.
 To use the SCART (SCART1) jack on the unit, select 
“SCART 1”.
 To use the SCART (SCART2) jack on the unit, select 
“SCART 2”.
 To use the PC-IN (RGB) jack on the unit, select “PC”.
 To use the HDMI-IN (HDMI 1) jack on the unit, 
select “HDMI 1”.
 To use the HDMI-IN (HDMI 2) jack on the unit, 
select “HDMI 2”.
 To use the HDMI-IN (HDMI 3) jack on the unit, 
select “HDMI 3”.
DTVATV
Select Input
TV
VIDEO
COMPONENT
SCART 1
SCART 2
PC
HDMI 1
HDMI 2
HDMI 3
 
						

							13EN
Sound Select
1)Press [SOUND] to display the currently selected audio 
language and the number of available languages.
2)Press [SOUND] repeatedly to cycle through the available 
audio languages.
1)Press [SOUND] to display the currently selected audio mode.
2)Press [SOUND] repeatedly to cycle through the available 
audio mode.
TV Screen Information
You can see the broadcasting information.
1)Press [I(information)].
 Fewer information menu will appear.
2)Press [I(information)] again to display more informations.
3)Press [BACK] to exit.
 TV Screen information menu will automatically disappear in a 
few seconds. 1.Nicam Stereo   Mono
2.Nicam Dual1   Nicam Dual2   Mono
3.Nicam Mono   Mono
4.Stereo  Mono
5.Dual1  Dual2
6.Mono
DTV
ATV
DTVATV
576i SD 16:9ETV07:00-09:5909:3718
1/3






Hit MusicYoure turned to the Sounds, keep it here for the biggest
sounds around, it doesnt get fresher than this! Call
09012 345 678 now to select a video
English English
Items
1Channel name
2Present programme name / time
3Programme information
4Current time
5Channel number
6Resolution / Format / TV aspect ratio
7Audio mode (ATV)
Audio language (DTV)
8Subtitle (p. 25)
  is displayed if the subtitle of the TV programme is 
available.
9ATV broadcast
  is displayed when it receives analogue TV broadcast.
DTV broadcast
  is displayed when it receives digital TV broadcast.
Radio service
  is displayed when it receives digital audio broadcast.
10Lock status (p. 26)
  is displayed when you are watching the TV programme 
which you set the parental lock or channel lock.
11Parental rating (p. 27)
  is displayed if the parental rating of TV programme is 
available. 
* The icon may differ depending on the ratings.
12Pay TV
  is displayed, when you are watching the pay TV.
13Teletext (p. 25)
  is displayed if the teletext of TV programme is 
available.
14Audio Description (p. 19)
  is displayed when the TV programme provides 
additional audio description for visually impaired.
Note:When the programme information consists of more than 
3 lines, press [K / L] to scroll.
 
						

							14EN
EPG (Electronic Programme Guide)
You can easily find a channel or see the detailed channel 
information. EPG gives you scheduled information of the TV 
programmes.
1)Press [GUIDE].
 EPG will appear.
2)Press [K / L] to select a channel, then press [1].
 Press [RED] or [GREEN] to move the channel list to the 
previous or next page.
 Press [OK] to watch the selected channel.
3)Press [K / L] to select a programme.
 Press [RED] or [GREEN] to move the programme list to the 
previous or next day.
 Press [OK] to watch the selected programme if it is currently 
available.
4)Press [YELLOW] to display more detailed programme 
information.
5)Press [GUIDE] to exit.
Note:When the programme information consists of more than 
2 pages, press [RED] or [GREEN] to move to the 
previous or next page.
DTV
ETV 18 19:00
19 Euro CH 20:00
21 WNS 22:50 20 Drama Now! 22:00
22
BCT 23:00
19:00 - 20:0021:16:27
Television TV guideViewing date: ThuOct Current time: ,04 Thu Oct,04
Hit Music
Special
Our Home
Pick Up Number
The Frying Winem
Music
Prev page Next page
20:00-22:00   Euro CH1/1Television
TV guide Detail
BB Special: Mr.Smith introduces unseen items from previous programmes
in the series and talks to expect Mrs. Cole about the history of BB House.
Music
Prev page Next page Return
 
						

							15EN
Changing the TV Screen Display Mode
You can select your favourite TV screen size.
Press [ASPECT] repeatedly to switch the TV screen display 
mode.
For SD (Standard Definition) video signal
“Auto”
Selects the TV screen display mode automatically.
This is the default.
“Sidebar”
Displays a 4:3 picture at its original size. Sidebars appear on both 
edge of the TV screen.
“Full”
Displays a 4:3 picture at a 16:9 size; the picture is stretched 
horizontally to fill the TV screen.
“Cinema”
Displays a 4:3 picture at a 16:9 size; the picture is stretched 
horizontally and vertically to fill the TV screen. This crops out the 
top and bottom of the picture.
“Wide”
Displays a 4:3 picture at a 16:9 size; the centre of the picture is at 
its original size and the edges stretched horizontally to fill the TV 
screen.
“14:9”
Displays a 4:3 picture at a 14:9 size. Sidebars will be displayed on 
both edge of the TV screen.
For HD (High Definition) video signal
“Auto”
Selects the TV screen display mode automatically.
This is the default.
“Full”
Displays a 16:9 picture at its original size.
“Zoom”
Displays a 16:9 picture at its maximum size without changing its 
horizontal and vertical ratio.
“Cinema”
Displays a vertically stretched picture.
“Expand”
Displays a horizontally stretched picture.
For PC input signal
“Normal”
Displays a proportionally stretched picture. Mainly sidebars 
appear on both edges of the TV screen.
“Full”
Displays a picture that is stretched out of proportion to fill the TV 
screen.
“Dot by Dot”
Displays a picture at its original size.
DTVATV
“Sidebar”
“Full”
“14:9”
“Cinema”
“Wide”“Auto”
“Full”
“Zoom”
“Expand”
“Cinema” “Auto”
“Normal” “Full”
“Dot by Dot”
 
						

							16EN
OTHER SETTINGS
Picture Adjustment
You can adjust the picture settings according to your personal 
preference. These settings are automatically stored after exiting the 
picture menu.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “Picture”, then press [OK].
“Picture Mode”
3)Press [K / L] to select “Picture Mode”.
4)Press [0 / 1] to select the setting (“Standard, Dynamic, 
Movie, News, Personal”) you want.
“Brightness, Contrast, Colour, Hue, Sharpness”
3)Press [K / L] to select the item you want, then press [OK].
4)Press [0 / 1] to adjust, then press [OK].“Colour Temperature”
3)Press [K / L] to select “Colour Temperature”.
4)Press [0 / 1] to select the setting (“Cool, Normal, Warm”) 
you want.
5)Press [MENU] to exit.
Note:Press [K / L] to change the items.
Note: When this unit is connected to PC, you can not select 
“Colour”, “Hue” and “Sharpness”.
 If you adjust the settings in other than “Personal” 
mode, “Picture Mode” will be changed to “Personal”.
Setting[0][1]
Brightnessdecrease 
brightnessincrease 
brightness
Contrastdecrease 
contrastincrease 
contrast
Colourdecrease 
colourincrease  
colour
Hueadd red add green
Sharpnessmake soft make clear
DTVATV
BACK
50755004
Picture
Sound
TV
Setup
ParentalPicture Mode
Standard
Brightness
Contrast
Colour
Hue
Sharpness
Colour Temperature Normal
Features
Select Back Picture
50Brightness
75Contrast
50Colour
0Hue
4Sharpness
BACK
50755004
Picture
Sound
TV
Setup
ParentalPicture Mode
Brightness
Contrast
Colour
Hue
Sharpness
Colour Temperature Normal
Features
Select Back Picture
Standard
 
						

							17EN
Advanced Picture Adjustment
You can adjust the detailed picture settings according to your 
personal preference.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “Picture”, then press [OK].
3)Press [K / L] to select “Features”, then press [OK].
 “Features” menu will appear.
“DNR (Digital Noise Reduction)”
You can adjust to reduce the appearance of digitizing error caused 
by the compression.
4)Press [K / L] to select “DNR”.
5)Press [0 / 1] to select the setting (“Low, Mid, High”) you 
want.
“CTI (Colour Transient Intensity)”
You can adjust the picture for colour errors.
4)Press [K / L] to select “CTI”.
5)Press [0 / 1] to select the setting (“Low, Mid, High”) you 
want.“Flesh Tone”
You can set to activate the flesh colours or not.
4)Press [K / L] to select “Flesh Tone”.
5)Press [0 / 1] to select the setting (“On, Off ”) you want.
“Adaptive Luma Control”
You can adjust changes in the luminance of the picture.
4)Press [K / L] to select “Adaptive Luma Control”.
5)Press [0 / 1] to select the setting (“On, Off ”) you want.
“Backlight”
4)Press [K / L] to select “Backlight”, then press [OK].
5)Press [0 / 1] to adjust, then press [OK].
6)Press [MENU] to exit.
DTVATV
BACK
100
Picture
Sound
TV
Setup
ParentalDNR Mid
CTI
Mid
Flesh Tone
On
On
Adaptive Luma Control
Backlight
Features
Select Back
100Backlight
 
						

							18EN
PC Settings
You can adjust the PC screen position, clock and phase. Make sure 
your PC is connected.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “Picture”, then press [OK].
3)Press [K / L] to select “PC Settings”, then press [OK].
“Auto Adjustment”
4)Press [K / L] to select “Auto Adjustment”, then press [OK].
 Each setting will be adjusted automatically.
“H.Position, V.Position, Phase, Clock”
4)Press [K / L] to select the item you want, then press [OK].
5)Press [0 / 1] to adjust, then press [OK].
6)Press [MENU] to exit.
Sound Adjustment
You can adjust the sound settings according to your personal 
preferences. These settings are automatically stored after exiting 
the sound menu.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “Sound”, then press [OK].
 “Sound” menu will appear.
“Balance, Bass, Treble”
3)Press [K / L] to select the item you want, then press [OK].
4)Press [0 / 1] to adjust, them press [OK].
“Virtual Surround Sound”
Virtual Surround Sound gives you the stereo phonic virtual space 
through your existing 2-channel stereo system.
3)Press [K / L] to select “Virtual Surround Sound”.
4)Press [0 / 1] to select the setting (“On, Off ”) you want.
“Sound Mode”
3)Press [K / L] to select “Sound Mode”.
4)Press [0 / 1] to select the setting (“Standard, Movie, Music, 
News”) you want.
Note:Press [K / L] to change the items.
Setting[0][1]
H.Positionmove PC 
screen leftmove PC 
screen right
V.Positionmove PC 
screen downmove PC 
screen up
Phase
decrease 
setting valueincrease 
setting valueClock
BACK
605018130
Picture
Sound
Setup
ParentalAuto Adjustment
H.Position
V.Position
Phase
Clock
PC Settings Enter Select Back
60H.Position
50V.Position
18Phase
130Clock
Note:Press [K / L] to change the items.
Setting[0][1]
Balance
decrease increaseBass
Treble
DTVATV
BACK
5050
0Picture
Sound
TV
Setup
Parental
Sound
Balance
Bass
Treble
Virtual Surround Sound
Off
Off Sound Mode Standard
Auto Volume  Control
Assistive Services -
Visually Impaired
Adjust Select Back
0Balance
50Bass
50Treble
 
						

							19EN
“Auto Volume Control”
You can set to keep a constant loudness differential between the 
TV commercials and the programs.
3)Press [K / L] to select “Auto Volume Control”.
4)Press [0 / 1] to select the setting (“On, Off ”) you want.
“Assistive Services”
You can adjust the audio type.
3)Press [K / L] to select “Assistive Services”.
4)Press [0 / 1] to select the setting (“-, Hearing Impaired, 
Visually Impaired”) you want.
5)Press [MENU] to exit.
“Visually Impaired”
Make sure “Visually Impaired” is selected at “Assistive Services” 
setting.
3)Press [K / L] to select “Visually Impaired” then press [OK].
4)Press [K / L] to select “Volume” then press [OK].
5)Press [0 / 1] to adjust, then press [OK].
6)Press [MENU] to exit.
Country Setting
You can select the channels according to the country you select.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
3)Press [K / L] to select “Country”.
4)Press [0 / 1] to select the country you want.
5)Press [MENU] to exit. Visually Impaired: provides additional audio description for 
visually impaired.
Hearing Impaired: provides audio service for hearing impaired.
Note:If you select “Visually Impaired”, you can adjust the 
audio volume for “Visually Impaired”.
DTV
DTV
20Volume
Note:You may not select the country depending on the 
location you purchased.
DTVATV
DTV
BACK
Picture
Sound
TV
Setup
ParentalFrance Country
Audio Language
Audio Language 2nd
Channel
SelectBack TV
English
English
ATV
BACK
Picture
Sound
TV
Setup
ParentalCountry France
Audio Channel
Stereo
Channel
Select Back TV
 
						

							20EN
Audio Language Selection
You can select the main language.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
“Audio Language”
3)Press [K / L] to select “Audio Language”.
4)Press [0 / 1] to select the language you want.
“Audio Language 2nd”
3)Press [K / L] to select “Audio Language 2nd”.
4)Press [0 / 1] to select the language you want.
5)Press [MENU] to exit.
“Audio Channel”
3)Press [K / L] to select “Audio Channel”.
4)Press [0 / 1] to select the setting (“Dual1, Dual2, Stereo, 
Mono”) you want.
Auto Scan
You can scan the channels receivable in your area automatically.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
3)Press [K / L] to select “Channel”, then press [OK].
4)Press [K / L] to select “Auto Scan”, then press [OK].
 Scanning will start automatically.
 When the scanning is completed, “Scan Completed” 
message will appear.
If you press [MENU] during the scanning, this operation 
will be stopped and the lowest memorised digital channel 
will be displayed.
 Please note that after tuning, the analogue channels will be 
stored in the order that they are broadcast by your local 
transmitter. This may not be in the same order in which 
you would like them to be stored. If this is the case, you can 
change the order according to your preference. 
(Refer to “Channel Sort” on page 22.)
Note:While watching a programme, you can change the audio 
language easily using [SOUND] when it is available.
Note:While watching a programme, you can change the audio 
mode easily using [SOUND] when it is available.
DTVATV
DTV
BACK
Picture
Sound
TV
Setup
ParentalCountry France
Audio Language
Audio Language 2nd
Channel
Select Back TV
English
English
BACK
Picture
Sound
TV
Setup
ParentalCountryFrance
Audio Language
Audio Language 2nd
Channel
Select Back TV
English
English
ATV
BACK
Picture
Sound
TV
Setup
ParentalCountry France
Audio Channel
Stereo
Channel
Select Back
TV
DTVATV
BACK
60% 1
8
Picture
Sound
TV
Setup
ParentalScanning
Analogue:
Digital:
Auto Scan Cancel
 
						

							21EN
Analogue Manual Scan
You can adjust an analogue channel individually.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
3)Press [K / L] to select “Channel”, then press [OK].
4)Press [K / L] to select “Manual Scan (Analogue)”, then press 
[OK].
5)Press [the Number buttons] to enter the frequency.
 To select 24, enter [0] first, then press [2] and [4].
6)Press [K / L] to select “Scan Up” or “Scan Down”, then press 
[OK].
 Scanning will start automatically.
 When this scanning is completed, “Scan Completed” 
message will appear.
7)Press [MENU] to exit.
Single RF Scan
You can adjust a digital channel individually.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
3)Press [K / L] to select “Channel”, then press [OK].
4)Press [K / L] to select “Single RF Scan”, then press [OK].
5)Press [0 / 1] to select the channel number you want to scan, 
then press [OK].
 Scanning will start automatically.
 When this scanning is completed, “Scan Completed” 
message will appear.
6)Press [MENU] to exit.
Update Scan
You can scan the updated channels automatically.
1)Press [MENU] to display the menu.
2)Press [K / L] to select “TV”, then press [OK].
3)Press [K / L] to select “Channel”, then press [OK].
4)Press [K / L] to select “Update Scan”, then press [OK].
 Scanning will start automatically.
 When this scanning is completed, “Scan Completed” 
message will appear.
5)Press [MENU] to exit.
Channel List
You can easily find a channel you want.
1)Press [OK] while watching a programme.
 “Channel List” will appear.
2)Press [K / L] to select the channel you want to watch.
Press [RED] or [GREEN] to move to the previous or next 
page.
Press [OK] to watch the selected programme if it is 
currently available.
3)Press [BACK] to exit.
ATV
BACK
45.00 Picture
Sound
TV
Setup
Parental
Scanning (Analogue)
Start Frequency (MHz)
Scan Up
Scan Down
Manual Scan (Analogue) Back
DTV
BACK
0%
6021
Picture
Sound
TV
Setup
ParentalScanning (Digital)
Channel
Signal Strength
Single RF Scan BackSearch
ATV
Digital radio service
no icon
DTV
Note:You can edit the channel list. 
(Refer to page 22 to page 23.)
DTVATV
BACK
60% 1
8
Picture
Sound
TV
Setup
ParentalScanning
Analogue:
Digital:
Update Scan Cancel
DTVATV
18 ETV
19 Euro CH
20 Drama Now!
21 WNS
22 BCT
25 Starcast
38 Eurasia StationChannel List
Page up Page down