Fujitsu P27t 6 Ips Operating Manual

							Operation
Operation
Switching the device on and off
123
12
1=SwitchOn/Off
2 = Power supply indicator3 = 0 W switch
The colour of the LED indicator changes as follows:
LED indicator Status
blue
Monitor and computer are switched on (normal mode).
green
Monitor and computer are switched on (ECO mode).
orange
Monitor is not receiving a video signal or is in BASIC power saving
mode.
does not light up
Monitor is switched off (or is in 0W power-saving mode).
The 0 position of the 0 W switch (3) on the rear activates ECO power saving mode (0 W
operating mode), the I position switches to the BASIC power saving mode 
						

							Operation
Notes on power management
If your computer is equipped with power management (power saving mode), the monitor can
fully support this function. The monitor thereby distinguishes between the individual power
saving modes of the computer (standby mode, suspend mode and OFF mode).
Stage Operation Power-saving mode (0 W switch)
Normal
ECO ECO (0) BASIC (|)
Power supply
indicatorLights up blue Lit green is unlit illuminated orange
Display Max. brightness typ. 200
cd/m2unlitorange
Typical power
consumption
(without USB and
audio)126 W < 85 W reduced to 0 W
(only for VGA, DVI)reducedto
						

							Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor settings with the buttons
of the control panel
The buttons of the control panel have two functions. If the OSD menu is
activated, a description of the current function of the buttons is displayed
directly above the buttons at the edge of the screen. If the OSD menu is not
activated, you can make the following settings directly:
123
1 = Buttons for the OSD menu (On
Screen Display)
2 = ON/OFF switch3 = Power supply indicator
Select OSD language
If one ofthe buttons is being pressed for thefirst time for the OSD menu, the
selection screen for the language is displayed:
►Press the
ECO/or theINPUT/button to select the required language.
►Press the
MENU/button to confirm your entries or theAUTO/button to cancel the process.
After selecting the OSD language for thefirst time, you can change
it at any time in the OSD.
Performing auto-adjustment of the monitor
►Press theAUTO/button for about 1 second.
TheAuto Processingmessage appears
Picture quality and position are set to optimum values for your system.
Fujitsu Technology Solutions 19
 
						

							Operation
Selecting input signal (D-SUB/DVI-D/HDMI)
►Press theINPUT/buttontocalluptheInput selectsettings window.
►Press the
ECO/or theINPUT/button to select the desired
monitor connection (VGA, DVI or DP).
►Press the
MENU/buttontoconfirm your selection or theAUTO/button to cancel the process.
This setting window can also be called up when the OSD menu is locked.
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the
MENU/button for a few seconds while you switch
on the monitor using the ON/OFF switch.
The messageOSD locked / unlockedis displayed.
Please proceed in the same manner to release the locked OSD menu again.
Activate/deactivate ECO operating mode
The power consumption of the device can be decreased by reducing
the brightness of the picture.
►Press the
ECO/button to switch the ECO operating mode on or off.
The messageECO Mode einorECO Mode offappears.
If the ECOoperating mode is activated, the following OSD settings are changed:
Mode
Office
Colour
6,500 K
Brightness
reduced
After the ECO operating mode is switched off, the brightness previously set by the user is restored.
20 Fujitsu Technology Solutions
 
						

							Operation
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press and hold the
ECO/andINPUT/buttons at the same time for a few seconds.
The messagePower button locked / unlockedis displayed.
Proceed in the same way to release the locked ON/OFF switch again.
Fujitsu Technology Solutions 21
 
						

							Operation
Changing the monitor settings using the OSD menu
With the buttons on the control panel, you can call up and use the integrated
OSD (On-Screen Display) menu.
The English menu names are used in the following description (default setting).
►Press theMENU/button to activate the OSD menu.
The main menu appears, with icons for the setting functions.
Thefirst symbol, (Brightness/Contrast), is highlighted and the associated functions
are visible in the right-hand menufield.
►Press the
ECO/or theINPUT/button to highlight another icon (e.g.Image adjust).
►Press the
MENU/button to select the highlighted icon.
TheImage adjustsettings window is displayed.
►Press the
AUTO/button to exit the main menu.
22 Fujitsu Technology Solutions
 
						

							Operation
►Press theECO/or INPUT /button to highlight another function.
►Press the
MODE/button or the/button to change the setting.
►Press the
ECO/or theINPUT/button to highlight another function.
►Press the
MENU/button to save the change or press theAUTO/button
to exit thefunction without making any changes.
If you want to change other settings, select the corresponding function from the OSD
main menu. All possible adjustments of the main menu are described in the following.
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
Fujitsu Technology Solutions 23
 
						

							Operation
Adjusting the brightness and contrast
Call up theBrightness/Contrastsetting window
Brightness
Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast
Set the contrast of the display
With this function you modify the contrast of bright colour tones.
Black level
Set the brightness of the display
With this function you modify the contrast of dark colour tones.
Auto Brightness
Automatic brightness control
This function is used to automatically control the brightness of the
background lighting using the light sensor.
On= The brightness is adjusted according to the ambient brightness
Off= The brightness is adjusted manually by the user
Auto level
Adjust the signal level
With this function you can automatically set the contrast.
The function is executed with the
button.
If the contrast is set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low,the maximum brightness will not be achieved.
Selecting the application mode
Call up theModesetting window
D mode
Setting forDICOM simulation (the values for colour and ACR are locked:
Colour = 7500K, ACR = off)
Office
Office presets (the settings forcolourandsharpnesscan be adjusted)
Photo
Photo presets (colour,sharpness,saturation,ACR)
Vi d e o
Video presets (colour,sharpness,saturation,ACR)
ACR= Dynamic contrast (on / off)
24 Fujitsu Technology Solutions
 
						

							Operation
Adjusting the picture size and position
Call theImage adjustsetting window
Phase
Eliminate picture disturbance
With this function youfine-tune your monitor to eliminate picture disturbance.
Clock
Set synchronisation
With this function you adjust the picture width to eliminate vertical picture
disturbances.
H-Position
Adjust the horizontal position
With this function you move the picture to the left or to the right.
V-Position
Adjust the vertical position
With this function you move the picture up or down.
Sharpness
Adjust the sharpness of the picture for thePhotoandVi d e omodes.
Saturation
Adjust the saturation for thePhotoandVi d e omodes.
Expansion
Adjust the picture size
Full screen= selection of full screen mode
Keep aspect= maximum picture size without distortion (only for PC image)
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Fujitsu Technology Solutions 25
 
						

							Operation
Setting colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in Kelvin (K). You can choose between
sRGB,6500 K,7500 K,9300 K,AdobeRGB,NativeandCustom Colour.
The optionssRGB,AdobeRGB,NativeandCustom colourare only available in
Officemode setting.
In the user-defined setting you can change the colour ratios of the basic
colours (red, green, blue) as required.
The6500KandsRGBsettings are recommended for general Windows
applications.
TheAdobeRGBsetting is for applications in the enhancedAdobeRGBcolour
space.
The full colour space of the LCD panel can be used in theNativeandCustom
Coloursettings.
Setting functions
Call up theSetupsettings window
Input select
Select the input signal
This function is used to select the input signal (VGA, DVI, DP, HDMI1 or
HDMI2).
This is on condition that the display adapter supports this function.
Language
Set the language for the OSD menu
With this function you select the language for the OSD menu.
The default setting is English.
DDC-CI
Activates/deactivates the DDC-CI function
On= The DDC-CI function is activated (default setting)
Off= The DDC-CI function is deactivated
OSDTimeout
Set the display duration of the OSD menu
With this function you select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is
automatically faded out.
Factory recall
Activate the factory settings
With this function all settings are reset to the factory settings without
prompting for confirmation.
The function is executed with the
button. If you are using a VGA data
cable, anAuto Processingmessage is displayed. The language selection
menu appears.
26 Fujitsu Technology Solutions