Fujitsu P27t 6 Ips Operating Manual

Important notes
Important notes
Importantnotes NotesIn this chapter you willfind information regarding safety which it is essential to
take note of when working with your device.
Safety instructions
This device complies with the relevant safety regulations for data processing equipment,
including electronic office machines for use in an office environment. If you have
any questions about whether the device can be used in the intended environment,
please contact your sales office or our Service Desk.
• The...

Important notes
• The device must only be operated in landscape mode (0°) and portrait mode (90°). The
control buttons are located in the middle of the bottom of the monitor in landscape mode
(0°) and at the left-hand side of the monitor in portrait mode (90°).
• Store this manual close to the device. If you pass the device on to third
parties, you should pass this manual on with it.
• We recommend that you place your device on a durable, non-slip surface. In view
of the many differentfinishes and...

Important notes
CE marking
The shipped version of this device complies with the requirements of EEC
directives 2004/108/EC Electromagnetic compatibility and 2006/95/EC
Low voltage directive.
Power management
The Fujitsu LCD monitor is equipped with power management which, when in 0W power
saving mode, reduces the power consumption to 0W (for VGA and DVI).
Disposal and recycling
This device has been manufactured as far as possible from materials which can be recycled or
disposed of in such a way that the...

Getting started
Getting started
Unpacking and checking the delivery
The display surface of the device is sensitive to pressure and scratches.
Always hold the device by the casing!
The complete device package includes:
• one monitor
• one data cable (DP)
• one data cable (DVI Dual Link)
•oneUSBcable
• one audio cable
• one power cable
• one CD with software and documentation
• one Warranty Booklet
• one Quick Start Guide brochure
• one Safety manual
►Unpack all the individual parts.
►Check the contents of...

Getting started
Setting up an ergonomic video workstation
1
►Do not position the video workstation
opposite a window (1).
1►Position the monitor outside the reach
of a light source (1).
1
►Position the keyboard where it is
easiest to reach (1).
Fujitsu Technology Solutions 11
 

Getting started
1
50 cm
►Position the monitor so that the eye distance
to the screen (1) is around 50 cm.
30
30 65
65 0
60
1
2 2►Position the monitor for optimum viewing
(1). The monitor should under no
circumstances fall outside the permissible
viewing space (2).
Depending on the situation, it may be advisable to use a swivel arm or wall
bracket (VESA FPMPMI), which are available from specialist dealers. For
this purpose the monitor base must be removed beforehand as described
in Chapter...

Getting started
Adjusting height
The height adjustment isfixed in the transport position.
1 2
►To free thefixing, remove the locking
pinontheflange (1).
The height of the monitor can be adjusted
by approximately 120 mm.
►Grasp the monitor with both hands on
the right and left edge of the casing
and move it up or down (2).
Adjusting the inclination
The inclination of the monitor can be adjusted by - 5° (forward) and +25°
(back) from its vertical position.
►Hold the monitor with both hands on the left and...

Getting started
Removing monitor base
Before you can use a swivel arm or a wall bracket, you must remove the monitor base.
The display surface is susceptible to scratching!
1
1 1
1
►Switch off the monitor and pull the power
plug out of the power socket.
►Lay the monitor on its face on a soft surface.
►Remove the cover and disconnect all cables.
►Remove the screws (1) on the rear
of the monitor.
You can now mount a swivel arm or a wall
bracket in accordance with VESA FPMPMI
using a hole spacing of 100...

Getting started
Connecting the device
Please observe the safety information inImportantnotes,Page7.
CE conformance and optimum picture quality are guaranteed only if
you use the data cables supplied.
►Switch off the monitor and the computer.
►Disconnect the power plugfrom the computer.
Connecting cables to the monitor
The monitor ports are protected by a cover.
The supplied data cables have two 15-pin D-SUB connectors or two 24-pin DVI connectors
or two 20-pin DP-connectors for connection to the monitor...

Getting started
►Select the appropriate data cable for your computer.
►Connect one of the connectors of the data cable to the DVI-D socket or the DP socket of
the monitor and secure the DVI-D connection by tightening the safety screws.
If you use a DP or HDMI data cable, you must set the 0 W switch to the basic position.
If you use a VGA or DVI Dual Link data cable, when the PC is switched off you can
move the 0 W switch to the ECO position to enable the 0 W power saving mode.
The monitor automatically...