Fujitsu F02d Manual

19
Introduction
~Wireless LAN (WLAN) exchanges information using 
radio waves, and allows you to freely establish LAN 
connection if you are within an area where radio wave 
reaches. On the other side, if you communicate 
without appropriate security settings, 
communications may be intercepted or hacked by 
malicious parties. It is recommended to make 
necessary security settings on your judgement and 
responsibility.
~Wireless LANDo not use Wireless LAN in a place where magnetized 
by electric...

20
Introduction
~FeliCa reader/writer function of FOMA terminal uses 
weak waves requiring no licenses for radio stations.
~It uses 13.56 MHz frequency band. When using other 
reader/writers in your surroundings, keep FOMA 
terminal away sufficiently from them. Before using 
the FeliCa reader/writer, confirm that there are no 
radio stations using the same frequency band nearby.
~FM transmitter of FOMA terminal uses weak waves 
requiring no licenses for radio stations.
~It uses 77.4 - 85.0MHz...

21
Introduction
Waterproofness/Dustproofness
F-02D provides waterproofness of IPX5*1, IPX8*2 
and dustproofness of IP5X*3 with firmly closing 
the external connection jack cap and installing 
the back cover in a locked state.
*1IPX5 means that a phone keeps functioning after 
applying a jet flow of 12.5 L/min. from every 
direction from a distance of approximately 3 m for at 
least 3 minutes using water nozzle in 6.3 mm inner 
diameter.
*2For F-02D, IPX8 means that a phone keeps 
functioning after F-02D...

22
Introduction
After using the external/HDMI connection jack, 
close the cap as the direction shown in the 
illustration, and make sure that the cap is 
completely closed without slack by pushing the 
tabs in.
~For installing the back cover, see Installing back 
cover of Attaching docomo mini UIM card/
battery pack.
ðP25~Securely lock the back cover and firmly close the 
external connection jack cap. Even a fine 
obstacle (one hair, one grain of sand, tiny fiber, 
etc.) put between contact surfaces...

23
Introduction
~Do not move in water or slam the terminal 
against the surface of water with FOMA terminal 
opened.
~If you put the terminal in tap water or in water of 
swimming pool, be sure to have it within 30 
minutes.
~When you use the terminal in swimming pool, 
obey rules of the facility.
~FOMA terminal does not float on water.~Do not leave water on FOMA terminal. May 
short-circuit the power jacks, or in a cold region, 
water may freeze causing malfunction.
~Do not leave water on the...

24
Introduction
When FOMA terminal is wet, water may flow out after 
wiping it off; drain the water in the following steps.
aWipe off moisture on the FOMA terminal 
surface and back side with dry, clean cloth etc.
bShake FOMA terminal approximately 20 times, 
firmly holding its hinge section, until there is 
no more water splattering.
cPress lightly FOMA terminal against dry, clean 
cloth etc. to wipe off water remaining in the 
microphone, earpiece, speaker, keypad, hinges 
or charging jack, etc.
dWipe...

25
Basic Operation
Before Using
Attaching docomo mini UIM card/battery pack
After turning power OFF, close FOMA terminal 
and hold it in your hand so that you can properly 
attach docomo mini UIM card/battery pack.
✜ Removing back cover
✜ Attaching docomo mini UIM card
Point
KOnly docomo mini UIM card is available for the 
FOMA terminal. If you have a UIM or FOMA card, 
bring it to docomo Shop to replace.
✜ Installing battery pack
✜ Installing back cover
Point
KMake sure the locations of the slots for...

26
Basic Operation
Before Using
Charging
The battery pack does not have a full charge at time of purchase. Use AC adapter for FOMA terminal to 
charge the battery before using FOMA terminal.
aInsert the connector of AC adapter 
horizontally to the accessory desktop 
holder, with the arrows mark side 
upward
bUnfold the power plug and insert it into 
a 100V AC outlet
cClose FOMA terminal and insert it into 
the desktop holder
dCheck that the charging light turns on*After charging is completed, remove FOMA...

27
Basic Operation
Before Using
Power ON - Default setting
Initial setting is an operation when FOMA terminal 
is turned ON for the first time.
af (2 sec. or more)The Initial setting screen appears.
bSet required itemseC [Complete]If you exit without setting Change security 
code and Request permit/deny., Initial setting 
screen reappears when the power is turned 
ON the next time.
cOn a confirmation screen of software 
update function, g eOn the 
confirmation screen of Error info send 
set., 
gThe...

28
Basic Operation
Screen Explanation
Viewing display
New arrival information and current state can be 
checked by the icon appearing on the screen. 
Major icons are as follows.a Status areaStatus icons are displayed. Select an area to 
display the status menu.ðP30
Battery level (Battery icon)
Signal strength (Antenna icon)
 : Self mode ON : In data transfer mode : Connecting to i-mode : Display off lock setting in Auto-key lock is set : Infrared communication in operation : Bluetooth ON : The total...