Fujitsu F02d Manual

21
❖Setting for Windows XP
1Click µ»”Ä (Start) àSelect  b‚owÓé¬åÜ (All programs) àž«
·±æ (Accessories) àè	ô (Communication) and click  	ý`M
€¢Ÿ
²”Å (New connection wizard).
2On the   (Start new connection wizard start) 
screen, click   (Next).
3Select  ï»”É¿Ät
€b” (Connect to Internet) and click    
(Next).
4Select  
€›	ˆp·¿Äž¿Ób” (Set up connection manually) and 
click   (Next).
5Select  ¼ àçž¿ÓÞÃÜ›–;`o
€b” (Use dialup modem to...

22
8Enter ┲”Ê (User name) àEnter  ͵ë”Å (Password) àEnter  ͵
ë”Åw¬ÝÖ— (Password confirmation entry) àSelect all items as shown 
below and click   (Next).

KIn ┲”Ê (User name) and  ͵ë”Å 
(Password), enter the user name and password 
specified by your provider or network 
administrator.

KWhen the access point is mopera U or mopera, 
you do not need to enter  ┲”Ê (User 
name),  굑Ӂ (Password) or  굑Ӂ
w¬ÝÖ—  (Password confirmation entry).
9On...

23
13Click É¿Ä딫 (Network) tab àSet each item as shown below àClick 

ƒ (Settings).

KWhen settings of IP and DNS information have 
been requested from the provider, etc. select   
ﻔɿÄÓéįç (TCP/IP) (Internet 
protocol (TCP/IP)), click  ÓéÍŸ (Property) 
and set necessary information.

KSince QoS Í­¿Äµ­´á”å (QoS packet 
scheduler) settings in  \w

24
4Enter ┲”Ê (User name) àEnter  ͵ë”Å (Password) àClick  ¼ 
àç (Dial).

KIn  ┲”Ê (User name) and  ͵ë”Å 
(Password), enter the user name and password 
specified by your provider or network 
administrator.

KWhen using mopera U or mopera, you do not 
need to enter  ┲”Ê (User name) or  ͵
ë”Å (Password).

KWhen  ┲”Ê (User name) was entered or 
굑Ӂ (Password) was saved while settings, 
these entries are no longer necessary.

KClick OK when the...

25
Connecting to a Wi-Fi compatible PC
Even out of public wireless LAN area, you can perform packet communication with 
connecting a Wi-Fi compatible PC to use FOMA terminal as an access point.

K
Switch FOMA terminal to AP mode ON in advance. For AP mode settings, refer to Instruction manual 
(detailed version) (in Japanese only) (PDF file) of the FOMA terminal.
 Under Windows 7
1Click  (Start) à¯ïÄé”çÍÉç (Control panel) àÉ¿Ä딫w	Ý6
q»µ«w
¯Ô (Network status and tasks) in the...

26
AT command
AT commands are commands for setting FOMA terminal functions using a PC. FOMA 
terminals comply with AT commands and support some extended commands and 
proprietary AT commands.
❖AT command input format
AT must be entered before each AT command. Commands must be entered in one-byte alphanumeric 
characters.
 Connecting to mopera U with ATD command
AT commands and their parameters must be entered on a single line. All the characters from the first 
character until the character directly...

27
×List of AT command

KThe followings are AT command that can be used via the FOMA F02D (Modem).
KEntering  Ç may cause \ to appear depending on the font setting for a PC or communication software.
KIf the battery pack is removed from FOMA terminal be fore the terminal power is turned off, the setting 
values may not be recorded.
Upper slot : Command Lower slot : ExampleDescription
A/ Execute the previously executed command again.
When previous response is ERROR, ERROR is returned.
A/
OK
AT Use...

28
ATS4=Set the line feed (LF) character. When result  code is displayed as alphabetic characters, 
appends the character after the carriage return (CR) character.
n=10 (fixed value)
ATS4? : Display current settings
ATS4=10
OK
ATS5=
Set the back space (BS) character. When this  character is detected during command input, 
the last character in the input buffer is deleted.
n=8 (fixed value)
ATS5? : Display current settings
ATS5=8
OK
ATS6=
Set pause time (seconds) until dia ling commences but do not...

29
AT&E*1Set the speed display used when connection is made.
n=0 : Display communicati on speed of wireless zone
n=1 : Display communication speed between a PC and FOMA terminal (default)
AT&E1
OK
AT&F
Reset the current setting to the default.
When this command is executed during communica tion, the terminal is reset after the line 
is disconnected (displaying NO CARRIER).
AT&F
OK (When in offline mode)
AT&S
*1Set control of the data set ready 
(DR) signal to be output to DTE.
n=0 : Always ON (default)...

30
AT+CBST=,1,0*1Set the line to use (Setting of bearer service)
n=116 : 64K data communication (default)yyn=134 : 64K videophone
AT+CBST? : Display current settings yyAT+CBST=? : Display a list of assignable values
AT+CBST=116,1,0
OK
AT+CDIP=
*1Set to notify/not to notify the sub address 
when receiving in packet communication or 64 
data communication. And, subscription stat us of Multi Number can be confirmed.
n=0 : The information of sub addr ess is not displayed. (default)
n=1 : The information...