Fujitsu B23t 6 Led Operating Manual

							Getting started
►Connect one of the connectors of the data cable to the D-SUB socket or the DVI-D socket or the
DP socket of the monitor and secure the plug connection by tightening the retaining screws.
The monitor automatically detects the input when only one signal source is connected.
►Insert one plug of the audio line in the AUDIO IN socket on the monitor
and make sure it is properly engaged.
►Plug the power cable supplied into the power connector of the monitor.
►Plug the supplied USB cable into the USB IN socket and the other end of
the cable into a USB socket of the computer.
Connect the USB keyboard and USB mouse directly to the PC, as the USB connector
socket of the monitor is switched off in energy-saving mode.
►Secure the cover over the connections.
A lock (Kensington Lock) can be mounted in the security slot to protect the monitor
against theft. A Kensington lock is not supplied with the monitor.
Connecting cables to the computer
Information on the computer connections and interfaces is contained in the
operating manual for your computer.
►Connect the data cable to the (active) monitor port on the computer and secure
the plug-in connection by tightening the safety screws.
►Insert the other plug of the audio cable in the audio output of the computer.
►Plug the power connector of the monitor into a properly grounded mains outlet.
►Plug the power connector of the computer into a properly grounded mains outlet.
If your computer has two monitor ports (onboard screen controller and separate
graphics card), the monitor port for the separate graphics card is active as standard.
Fujitsu Technology Solutions 17
 
						

							Operation
Operation
Switching the device on and off
12
12
1 = Switch On/Off 2 = Power supply indicator
The colour of the LED indicator changes as follows:
LED indicator Status
blue
Monitor and computer are switched on (normal mode).
green
Monitor and computer are switched on (ECO mode).
orange
Monitor is not receiving a video signal or is in power saving mode.
does not light up
Monitor is switched off.
►SwitchthedeviceonagainwiththeON/OFFswitch(1).
18 Fujitsu Technology Solutions
 
						

							Operation
Notes on power management
If your computer is equipped with power management (power-saving mode), the monitor can fully
support this function. Here the monitor does not distinguish between the individual energy-saving
modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of
immediately switching into the modewith the highest energy-saving effect.
Stage OperationPower saving mode
Normal
ECO
Power supply indicator Lights up blue Lit green is orange
Display Max. brightness
typ. 175 cd/m2unlit
Typical power
consumption (without
USB and audio)35 W 23 W reducedto
						

							Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor settings with the buttons
of the control panel
The buttons of the control panel have two functions. If the OSD menu is
activated, a description of the current function of the buttons is displayed
directly above the buttons at the edge of the screen. If the OSD menu is not
activated, you can make the following settings directly:
1234
1 = Buttons for the OSD menu (On
Screen Display)
2 = ON/OFF switch3 = Power supply indicator
4 = Softkeys
20 Fujitsu Technology Solutions
 
						

							Operation
Select OSD language
If one of the buttons is being pressed for thefirst time for the OSD menu, the
selection screen for the language is displayed:
►Press the
ECO/or theINPUT/button to select the required language.
►Press the
MENU/button to confirm your entries or theAUTO/button to cancel the process.
After selecting the OSD language for thefirst time, you can change
it at any time in the OSD.
Performing auto-adjustment of the monitor
►Press theAUTO/button for about 1 second.
TheAuto Processingmessage appears
Picture quality and position are set to optimum values for your system.
Selecting the input signal (D-SUB/DVI-D/DP)
►Press theINPUT/buttontocalluptheInput selectsettings window.
►Press the
ECO/or theINPUT/button to select the desired
monitor connection (VGA, DVI or DP).
►Press the
MENU/buttontoconfirm your selection or theAUTO/button to cancel the process.
This setting window can also be called up when the OSD menu is locked.
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the
MENU/button for a few seconds while you switch
on the monitor using the ON/OFF switch.
The messageOSD locked / unlockedis displayed.
Please proceed in the same manner to release the locked OSD menu again.
Fujitsu Technology Solutions 21
 
						

							Operation
Activate/deactivate ECO operating mode
The power consumption of the device can be decreased by reducing
the brightness of the picture.
►Press the
ECO/button to switch the ECO operating mode on or off.
The messageECO Mode einorECO Mode offappears.
If the ECO operating mode is activated, the following OSD settings are changed:
Colour
6,500 K
Brightness
reduced
After the ECO operating mode is switched off, the brightness previously set by the user is restored.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press and hold the
ECO/andINPUT/buttons at the same time for a few seconds.
The messagePowerbutton locked / unlockedis displayed.
Proceed in the same way to release the locked ON/OFF switch again.
Changing the monitor settings using the OSD menu
With the buttons on the control panel, you can call up and use the integrated
OSD (On-Screen Display) menu.
The English menu names are used in the following description (default setting).
22 Fujitsu Technology Solutions
 
						

							Operation
►Press theMENU/button to activate the OSD menu.
The main menu appears, with icons for the setting functions.
Thefirst symbol, (Brightness/Contrast), is highlighted and the associated functions
are visible in the right-hand menufield.
►Press the
ECO/button or theINPUT/button to highlight another icon (e.g.Image adjust).
►Press the
MENU/button to select the highlighted icon.
TheImage adjustsettings window is displayed.
►Press the
AUTO/button to exit the main menu.
Fujitsu Technology Solutions 23
 
						

							Operation
►Press theECO/button or theINPUT/button to highlight another function.
►Press the
MODE/button or the/button to change the setting.
►Press the
ECO/button or theINPUT/button to highlight another function.
►Press the
MENU/button to save the change or press theAUTO/button
to exit the function without making any changes.
If you want to change other settings, select the corresponding function from the OSD
main menu. All possible adjustments of the main menu are described in the following.
24 Fujitsu Technology Solutions
 
						

							Operation
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
Adjusting the brightness and contrast
Call up theBrightness/Contrastsetting window
Brightness
Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast
Set the contrast of the display
With this function you modify the contrast of bright colour tones.
Black level
Set the brightness ofthe display
With this function you modify the contrast of dark colour tones.
Auto level
Adjust the signal level
With this functionyou can automatically set the contrast.
The function is executed with the
button.
If the contrastis set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.
Adjusting the picture size and position
Call theImage adjustsetting window
Phase
Eliminate picture disturbance
With this function youfine-tune your monitor to eliminate picture disturbance.
Clock
Set synchronisation
With this function you adjust the picture width to eliminate vertical picture
disturbances.
H-Position
Adjust the horizontal position
With this function you move the picture to the left or to the right.
V-Position
Adjust the vertical position
With this function you move the picture up or down.
Expansion
Adjust the picture size
Full screen= selection of full screen mode
Keep aspect= maximum picture size without distortion (only for PC image)
Fujitsu Technology Solutions 25
 
						

							Operation
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Setting colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in K (= Kelvin). You can choose between
sRGB,6500 K,7500 K,9300 K,NativeandCustom Colour.
In the user-defined setting you can change the colour ratios of the basic
colours (red, green, blue) as required.
Adjusting the display of the OSD menu
Calling theOSD Setupadjustment window
Language
Selecting the language for the OSD menu
With this function you select the language for the OSD menu.
The default setting is English.
OSD Timeout
Setting the display duration of the OSD menu
With this function you can select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is
automatically hidden.
OSD Rotation
With this function you switch the OSD menu from portrait mode to landscape
mode and vice versa.
On = The OSD menu is displayed in portrait mode.
Off = The OSD menu is displayed in landscape mode.
26 Fujitsu Technology Solutions