Fujitsu B23t 6 Led Operating Manual

							Important notes
Important notes
Importantnotes NotesIn this chapter you willfind information regarding safety which it is essential to
take note of when working with your device.
Safety instructions
This device complies with the relevant safety regulations for data processing equipment,
including electronic office machines for use in an office environment. If you have
any questions about whether the device can be used in the intended environment,
please contact your sales office or our Service Desk.
• The display surface ofthe device is sensitive to pressureand scratches. You should therefore
be careful with the display surface in order to avoid lasting damage (scratches).
• If the device is brought into the installation site from a cold environment, condensation
can form. Before operating the device, wait until it is absolutely dry and has reached
approximately the same temperature as the installation site.
• When installing and operating the device, please observe the notes on environmental
conditions in Chapter
Technicalspecification,Page32as well as the instructions in
ChapterSettingupanergonomicvideoworkstation,Page11.
• To ensure sufficient ventilation, the air inlet and outlet openings of the device must be kept clear.
• The device automatically sets itself to the correct voltage within the range from 100 V to 240 V.
Make sure that the local mains voltage is neither higher nor lower than this range.
• Ensure that the power socket on the device and the mains outlet are freely accessible.
• The ON/OFF switch does not disconnect the monitor from the mains voltage. To disconnect
fully from themains supply, disconnect the power plug from the socket.
• The device is equipped with a power cable that complies with safety standards.
• Use the supplied power cable only.
• Lay the cables in such a way that they do not create a hazard (danger of tripping)
and cannot be damaged. When connectingthe device, observe the relevant
notes in chapter
Connectingthedevice,Page16.
• No data transfer cables should be connected or disconnected during a thunderstorm.
• Make sure that no objects (e.g. jewellery chains, paper clips, etc.) or liquids get
inside the device (danger of electric shock, short circuit).
• The device is not waterproof! Never immerse the device in water and protect
it from spray water (rain, sea water).
• In an emergency (e.g. damaged casing, operation controls or cables, penetration
of liquids or foreign matter), switch off the device, disconnect the power plug
and contact your sales outlet or our Service Desk.
• Repairs to the device must only be performed by qualified technicians. Unauthorised opening
and incorrect repair may greatly endanger the user (electric shock,fire risk).
• Only use the screen resolution settings and refresh rates specified in Chapter

Technicalspecification,Page32. Otherwise you may damage the device. If you
are in any doubt, contact your sales outlet or our Help Desk.
•Useascreen saver with moving images and activate the power management for
your monitor to prevent still images from burning in.
• If you operate the device with the swivel arm or wall bracket, it must not be turned by 180°.
Fujitsu Technology Solutions 7
 
						

							Important notes
• The device must only be operated in landscape mode (0°) and portrait mode (90°). The
control buttons are located in the middle of the bottom of the monitor in landscape mode
(0°) and at the left-hand side of the monitor in portrait mode (90°).
• Store this manual close to the device. If you pass the device on to third
parties, you should pass this manual on with it.
• We recommend that you place your device on a durable, non-slip surface. In view
of the many differentfinishes and varnishes used on furniture, it is possible that the
feet of the device may mark the surface they stand on.
• To ensure sufficient ventilation, the air supply and air outlet openings of
the monitor must never be blocked.
Power cable
Use the supplied power cable only.
Use the following guidelines if it is necessary to replace the original cable set.
• The female/male receptacles of the cord set must meet IEC60320/CEE-22 requirements.
• The cable has to be HAR-certified or VDE-certified. The mark HAR or
VDE will appear on the outer sheath.
• For devices which are mounted on a desk or table, type SVT or SJT cable sets may be
used. For devices which sit on thefloor, only SJT type cable sets may be used.
• The cable set must be selected according to the rated current for your device.
• If necessary, replace the original power cable with a regular grounded 3-core mains lead.
Transporting the deviceDevice , Tr ans por ta ti on
RetransportationTransport all parts separately in their original packaging or in a packaging which
protects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
If the device is brought from a cold environment into the room where it will be used,
condensation may occur. Before operating the device, wait until it is absolutely dry
and has reached approximately the same temperature as the installation site.
Cleaning the device
Switch off the device and unplug the power plug.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode plastic.
Ensure that no liquid enters the device.
The display surface of the device is sensitive to pressure and scratches. Clean
it only using a soft, slightly moistened cloth.
The surface of the casing can be cleaned with a dry cloth. If particularly dirty, use a cloth that
has been moistened in mild domestic detergent and then carefully wrung out.
8 Fujitsu Technology Solutions
 
						

							Important notes
CE marking
The shipped version of this device complies with the requirements of EEC
directives 2004/108/EC Electromagnetic compatibility and 2006/95/EC
Low voltage directive.
Disposal and recycling
This device has been manufactured as far as possible from materials which can be recycled or
disposed of in such a way that the environment is not damaged. The device may be taken back after
use to be reused or recycled, provided that it is returned in a condition that befits its intended use.
Any components not reclaimed will be disposed of in an environmentally acceptable manner.
The device must be disposed of in accordance with the local regulations for disposal of special waste.
If you have any questions on disposal, please contact your local sales office or our
Service Desk, or contact one of the following directly:
GermanyBelgium
Switzerland
Fujitsu Technology Solutions
GmbH
Remarketing and Recycling
D-33106 Paderborn
Tel.: +49 5251 / 81 80 10
Fax: +49 5251 / 81 80 15

http://ts.fujitsu.com/wvm
RECUPEL
Boulevard Reyers, 80
B-1030 Brussels
Tel.: +32 2 / 706 86 16
Fax: +32 2 / 706 86 13
E-Mail: [email protected]

http://www.recupel.be
SWICO
Schweizerischer
Wirtschaftsverband der
Informations-, Kommunikations-
und Organisationstechnik
AlistoftheSWICO
acceptance places can be
found at:
http://www.swico.ch
Asia
USA
Taiwan:
Environmental Protection
Administration
Executive Yuan R.O.C.

http://recycle.epa.gov.tw
Fujitsu America, Inc.
1250E. Arques Avenue
Sunnyvale, CA 94085 U.S.A.
Contact: Henning, Bernd
Phone No.: (408) 329-6737
Fax No.: (408) 746-8299
Information on this subject is also available on the Internet athttp://ts.fujitsu.com/recycling.
Fujitsu Technology Solutions 9
 
						

							Getting started
Getting started
Unpacking and checking the delivery
The display surface of the device is sensitive to pressure and scratches.
Always hold the device by the casing!
The complete device package includes:
• one monitor
• one data cable (DVI)
• one data cable (VGA)
•oneUSBcable
• one audio cable
• one power cable
• one CD with software and documentation
• one Warranty Booklet
• one Quick Start Guide brochure
• one Safety manual
►Unpack all the individual parts.
►Check the contents of the package for anyvisible damage caused during transport.
►Check whether the delivery conforms to the details in the delivery note.
►Should you discover that the delivery does not correspond to the delivery
note, notify your local sales outlet immediately.
Do not discard the original packing material of the devices. You may need the
packaging in the future if you need to transport your device.
10 Fujitsu Technology Solutions
 
						

							Getting started
Settingupthedevice
To ensure sufficient ventilation, the air inlet and outlet openings of
the device must be kept clear.
Setting up an ergonomic video workstation
1
►Do not position the video workstation
opposite a window (1).
1►Position the monitor outside the reach
of a light source (1).
Fujitsu Technology Solutions 11
 
						

							Getting started
1
►Position the keyboard where it is
easiest to reach (1).
1
50 cm
►Position the monitor so that the eye distance
to the screen (1) is around 50 cm.
30
30 65
65 0
60
1
2 2►Position the monitor for optimum viewing
(1). The monitor should under no
circumstances fall outside the permissible
viewing space (2).
Depending on the situation, it may be advisable to use a swivel arm or wall
bracket (VESA FPMPMI), which are available from specialist dealers. For
this purpose the monitor base must be removed beforehand as described
in Chapter
Removingmonitorbase,Page15.
12 Fujitsu Technology Solutions
 
						

							Getting started
Mounting the monitor base
Do not remove the retaining splint before you have secured the base plate on
the monitor and have brought it into operating position.
2
1
3
►Insert the base plate on the foot (1).
►Guide the screw through the opening (2).
►Secure the base plate with the screw (3).
►Place the monitor in operating position.
Fujitsu Technology Solutions 13
 
						

							Getting started
Adjusting height
The height adjustment isfixed in the transport position.
1 2
►To free thefixing, remove the locking
pin on theflange (1).
The height of the monitor can be adjusted
by approximately 120 mm.
►Grasp the monitor with both hands on
the right and left edge of the casing
and move it up or down (2).
Adjusting the inclination
The inclination of the monitor can be adjusted by -5° (forwards) and +35°
(backwards) from its vertical position.
►Hold the monitor with both hands on the left and right sides of the casing
and move it to the desired angle.
14 Fujitsu Technology Solutions
 
						

							Getting started
Removing monitor base
Before you can use a swivel arm or a wall bracket, you must remove the monitor base.
The display surface is susceptible to scratching!
1
1 1
1
►Switch off the monitor and pull the power
plug out of the power socket.
►Lay the monitor on its face on a soft surface.
►Remove the cover and disconnect all cables.
►Remove the screws (1) on the rear
of the monitor.
You can now mount a swivel arm or a wall
bracket in accordance with VESA FPMPMI
using a hole spacing of 100 mm.
For instructions on how to mount the swivel arm or wall bracket, please see
the documentation for the swivel arm or wall bracket.
Fujitsu Technology Solutions 15
 
						

							Getting started
Connecting the device
Please observe the safety information inImportantnotes,Page7.
CE conformance and optimum picture quality are guaranteed only if
you use the data cables supplied.
►Switch off the monitor and the computer.
►Disconnect the power plugfrom the computer.
Connecting cables to the monitor
The monitor ports are protected by a cover.
The data cables supplied have two 15-pin D-SUB connectors or two 24-pin DVI
connectors for connection to the monitor and to the computer.
Information on the computer connections and interfaces is contained in the
operating manual for the computer.
345
6789 12
9
1=Security slot for Kensington Lock
2 = Cover
3=Powerconnector
4 = Display Port (DP) socket
5=DVI-D socket (DVI)6=D-SUBsocket (VGA)
7 = AUDIO-IN socket
8=USBIN(Downstream)
9 = USB OUT (Upstream)
►Remove the cover.
►Select the appropriate data cable for your computer.
16 Fujitsu Technology Solutions