Fujitsu B19 W 5 Eco Operating Manual

							Operation
Operation
Switching the device on and off
2
1
1 = Power supply indicator 2 = ON/OFF switch
►Switch the device on using the ON/OFF switch.
Press the buttons from the bottom upwards.
Only switch on the computer after you have switched on the monitor.
The colour of the LED indicator changes as follows:
LED indicator Status
blue
Monitorand computer are switched on (normal mode).
green
Monitor and computer are switched on (ECO mode).
orange
Monitor is not receiving a video signal or is in power saving mode.
does not light up
Monitor is switched off
A26361-K1333-Z220-1-7619, edition 1 13
 
						

							Operation
Notes on power management
If your computer is equipped with power management (power-saving mode), the monitor can fully
support this function. Here the monitor does not distinguish between the individual energy-saving
modes of the computer (standby mode, suspend mode and OFF mode), as it is capable of
immediately switching into the modewith the highest energy-saving effect.
Level
OperationEnergy saving mode
Normal
ECO mode
Power supply
indicatorilluminated blue illuminated green illuminated orange
Display max. brightness
typ. 200 cd/m2unlit
Power consumption
(typical)< 28 W < 19 W reduced to≤0.5 W
If your computer detects inactivity (no input) it sends an appropriate signal to the monitor to
reduce the power consumption (energy-savingmode). The power indicator of the monitor changes
colour to indicate the status change. ECO mode is the preset factory default.
Once an input is made at the computer the screen contents are restored.
For detailed information on how energy-saving mode operates, please refer to
the operating manual or technical manual of the computer.
14 A26361-K1333-Z220-1-7619, edition 1
 
						

							Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor settingswith the buttons
of the control panel
The buttons of the control panel have two functions. With the OSD menu not
activated, you can make the following settings directly:
SELECT/ MENUINPUTEXIT / AUTO
123
ECO
1 = Buttons for the OSD menu (On-Screen
Display)
2 = Power supply indicator3 = ON/OFF switch
Performing auto-adjustment of the monitor
►Press theEXIT / AUTObutton for about 1 second.
TheAuto Processingmessage appears
Picture quality and position are set to optimum values for your system.
Selecting input signal (D-SUB/DVI-D)
►Press the Back /INPUTbutton to open theInput selectsetting window.
►Press the Forwards / ECO button or the Back /
INPUTbutton to select the
desired monitor connection (VGA or DVI).
This setting window can also be called when the OSD menu is locked.
A26361-K1333-Z220-1-7619, edition 1 15
 
						

							Operation
Activate/deactivate ECO operating mode
The power consumption of the device can be decreased by reducing
the brightness of the picture.
►Press the Forwards / ECO button to switch the ECO operating mode on or off.
The messageAction was executedappears.
If the ECO operating mode is activated, the following OSD settings are changed:
Colour
temperature6500K
Brightness
reduced
After the ECO operating mode is switched off, the brightness previously set by the user is restored.
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the
SELECT/MENUbutton for a few seconds while you switch
on the monitor with the ON/OFF switch.
TheAction was executedmessage appears.
Please proceed in the samemanner to release the locked OSD menu again.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press the Forwards / ECO button and the Back /
INPUTbutton at the same
time and keep them pressed for a few seconds.
The messageAction was executedappears.
Please proceed in the same manner to release the locked ON/OFF switch again.
Changing the monitor settings using the OSD menu
With the buttons on the control panel, you can call up and use the integrated
OSD (On-Screen Display) menu.
16 A26361-K1333-Z220-1-7619, edition 1
 
						

							Operation
The OSD menu is available in various languages. The English menu names are
used in the following description (default setting). You can select another language
using the OSDLanguagefunction in theOSD Setupmenu.
►Press theSELECT/MENUbutton to
activate the OSD menu.
The main menu appears, with icons
for the setting functions.
Thefirst icon, (Brightness/Contrast), is
highlighted and the associated functions are
visible in the right-hand menufield.
►Press the Forwards / ECO button or
the Back /INPUTbutton to highlight
another icon (e.g.Image adjust).
►Press the
SELECT/MENUbutton to
select the highlighted icon.
TheImage adjustsetup window will
be displayed.
►Press the Forwards / ECO button or
the Back /
INPUTbutton to highlight
another function.
►Press the
SELECT/MENUbutton to
select the highlighted function.
►Press the Forwards / ECO button or
the Back /
INPUTbutton to highlight
another function.
►Press the
EXIT / AUTObutton to
exit the function.
►Press the Forwards / ECO button or the
Back /
INPUTbutton to highlight another
function or press theEXIT / AUTObutton
to return to the main menu.
All changes are stored automatically.
A26361-K1333-Z220-1-7619, edition 1 17
 
						

							Operation
If you wish to change other settings, select the corresponding function from the OSD
main menu. All possible adjustments of the main menu are described below.
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
Adjusting the brightness and contrast
Call up theBrightness/Contrastsetting window
Brightness
Set the brightness of the display
With this function you can change the brightness of the background lighting.
You can see whether the ECO operating mode is active under the bar for
displaying the brightness setting.
Contrast
Set the contrast of the display
With this function you can modify the contrast of pale colours.
Black level
Set the brightness of the display
With this function you modify the contrast of dark colours.
Auto level *
Adjust the signal level
With this function you can automatically set the contrast.
The function is executed with the
SELECT / MENUbutton.
* function not available in DVI mode
If the contrast is set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low, the maximum brightness will not be achieved.
18 A26361-K1333-Z220-1-7619, edition 1
 
						

							Operation
Adjusting the screen size and position
Calling theImage adjustsetting window
H-position *
Adjustment of the picture horizontal position
With this function you can move the picture to the left or to the right.
V-position *
Adjusting the picture vertical position
With this function you can move the picture up or down.
Clock *
Adjusting the synchronisation settings
This function is used to adjust the picture width, to eliminate vertical picture
interference.
Phase *
Eliminating picture interference
With this function youfine-tune your monitor to eliminate picture interference.
Sharpness
Setting the picture sharpness
This function is used to adjust the picture sharpness.
* function not available in DVI mode
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Setting the colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in Kelvin (K). You can choose between
sRGB,6500 K,7500 K,9300 K,NativeandCustom Colour.
In the user-defined setting you can change the colour ratios of the basic
colours (red, green, blue) as required.
A26361-K1333-Z220-1-7619, edition 1 19
 
						

							Operation
Adjusting the display of the OSD menu
Calling theOSD Setupadjustment window
Language
Selecting the language for the OSD menu
With this function you choose between English (default setting), French,
German, Italian and Spanish as the language for the OSD menu.
OSDH position
Setting the horizontal position of the OSD menu
With this function you can move the OSD menu to the left or to the right.
OSDV position
Setting the vertical position of the OSD menu
With this function you can move the OSD menu up or down.
OSDTimeout
Setting the display duration of the OSD menu
With this function you can select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is
automatically hidden.
OSD Rotation
With this function you switch the OSD menu from portrait mode to landscape
mode and vice versa.
Off = The OSD menu is displayed in portrait mode.
On = The OSD menu is displayed in landscape mode.
Setting functions in the Advanced menu
Call up theAdvancedsetting window
Input select
Selecting the input signal
This function allows you to switch the monitor from analogue to digital mode
and vice versa, when two signal sources are connected.
This is on condition that the graphic card supports this function.
DDC-CI
Activation/deactivation of the DDC-CI
On= The DDC-CI function is enabled (standard setting)
Off= The DDC-CI function is disabled
ACR
Enable/disable dynamic contrast
On= The ACR function is enabled
Off= The ACR function is disabled
Factory Recall
Activating the factory settings
With this function all settings are reset to the factory settings without
prompting for confirmation.
Press the
SELECT/MENUbutton to activate the function. TheAuto
Processingmessage is displayed.
20 A26361-K1333-Z220-1-7619, edition 1
 
						

							Operation
Displaying information
Call theInformationsetting window
With this function the model designation, serial number, resolution, H/V
frequency, input signal and polarity of the synchronisation signal are
displayed.
A26361-K1333-Z220-1-7619, edition 1 21
 
						

							Troubleshooting
Troubleshooting
Should an error occur,first check the following points. If the distortion is still not eliminated,
the monitor should, if possible, be checked on another computer.
If you are unable to solve the problem, please inform our help desk.
Having this problem? Check the following points:
No screen display
Power indicator does not light up►Check whether the power cable on the
monitor is connected correctly.
►Check whether the computer isswitched on.
No screen display
Power indicator is lit►Check whether the computer is switched on.
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Press any key on the computer keyboard.
The computer may be in power saving
mode.
►Alter the brightness and/or contrast until you
get a picture.
Message:No Signal
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Check whether the computer is switched on.
Message:
Frequency out of range: ## kHz / ## Hz
Please change the display mode
to 1440 x 900 with 60 HzThe input signal (horizontal frequency and
refresh rate) at the displayed input does not
correspond to the technical data for the monitor.
►Adjust the video frequency range using the
computer software (see documentation for
the computer or display adapter).
►Set a different screen resolution using the
computer software (see documentation for
the computer or display adapter).
Picture position not correct
The monitor recognises an undefined mode (see
chapterTechnicalspecification,Page25).
►Press the
EXIT / AUTObutton to perform
auto-adjustment of the screen.
Picture is shaking
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Press the
EXIT / AUTObutton to perform
auto-adjustment of the screen.
Picture is wrongly adjusted►Press theSELECT / MENUbutton to
activate theFactory Recallfunction.
TheAuto Processingmessage appears.
Picture disturbances (vertical lines)►Press theEXIT / AUTObutton to perform
auto-adjustment of the screen.
22 A26361-K1333-Z220-1-7619, edition 1