Fujitsu A17 5 Eco Operating Manual

							Operation
Operation
Switching the device on and off

 

1 = Buttons for the OSD menu (On-Screen
Display)
2 = Power supply indicator
3 = ON/OFF switch
Press the buttons upwards from below.
The colour of the LED indicator changes as follows:
LED indicator Status
Blue
Monitor and computer are switched on (normal mode).
Not lit
The monitor is switched off (or is in power saving mode - power
consumption in standby and off mode≤1W).
►Switch the device on using the ON/OFF switch.
Only switch on the computer after you have switched on the monitor.
A26361-K1338-Z220-1-7619, edition 1 13
 
						

							Operation
Notes on power management
If the computer is equipped with power management(power-saving mode), then this function
can be fully supported by the monitor. The monitor does not distinguish between the individual
energy-saving modes used by the computer (standby mode, suspend mode and OFF mode), as
it is capable of immediately switching into the mode with the highest energy-saving effect.
Level
OperationPower saving mode
Normal
Power supply indicator Blue light
Orange light
Monitor Max. brightness Dark
Power consumption
(typical)
						

							Operation
Changing the monitor settings
When putting the monitor into operation for thefirst time, the screen display should
be optimally adapted to the display adapter used.
Changing the monitor settingswith the buttons
of the control panel
The buttons of the control panel have two functions. With the OSD menu not
activated, you can make the following settings directly:
1 = Buttons for the OSD menu (On
Screen Display)
2 = Power indicator3 = ON/OFF switch
Performing auto-adjustment of the monitor
►Press theEXIT / AUTObuttonfor about 1 second.
TheAuto Processingmessage appears
Picture quality and position are set to optimum values for your system.
Brightness adjustment
►Press the BACK /button to adjust the brightness.
This setting changes the backlight brightness.
Activating/deactivating muting
►Press the FORWARD /button to toggle sound off or on.
A message will be displayed confirming that the action has been performed.
A26361-K1338-Z220-1-7619, edition 1 15
 
						

							Operation
Locking the OSD menu
The OSD menu can be locked to prevent accidental or unauthorised changes to the monitor settings.
►Press and hold the
SELECT/MENUbutton for a few seconds while you switch
on the monitor with the ON/OFF switch.
TheAction was executedmessage appears.
Please proceed in the same manner to release the locked OSD menu again.
Locking the ON/OFF button
The ON/OFF switch can be locked to prevent accidental or unauthorised
changes to the monitor settings.
►Press and hold the Forwards /
button and the Back /button at
the same time for a few seconds.
TheAction was executedmessage appears.
Please proceed in the same manner to release the locked ON/OFF switch again.
Changing the monitor settings using the OSD menu
With the buttons on the control panel, you can call up and use the integrated
OSD (On-Screen Display) menu.
The OSD menu is available in various languages. The English menu names are
used in the following description (default setting). You can select another language
using the OSDLanguagefunction in theOSD Setupmenu.
16 A26361-K1338-Z220-1-7619, edition 1
 
						

							Operation
►Press theSELECT/MENUbutton to
activate the OSD menu.
The main menu appears, with icons
for the setting functions.
Thefirst icon, (Brightness/Contrast), is
highlighted and the associated functions are
visible in the right-hand menufield.
►Press the Forwards /button or the
Back /button to highlight another
icon (e.g.Image adjust).
►Press the
SELECT/MENUbutton to
select the highlighted icon.
TheImage adjustsetup window will
be displayed.
►Press the Forwards /
button or the
Back /button to highlight another function.
►Press the
SELECT/MENUbutton to
select the highlighted function.
►Press the Forwards /
button or the
Back /button to highlight another function.
►Press the
EXIT / AUTObutton to
exit the function.
►Press the Forwards /
button or the
Back /button to highlight another
function or press theEXIT / AUTObutton
to return to the main menu.
All changes are stored automatically.
If you wish to change other settings, select the corresponding function from the OSD
main menu. All possible adjustments of the main menu are described below.
A26361-K1338-Z220-1-7619, edition 1 17
 
						

							Operation
OSD menu functions
The OSD menu for analogue monitor operation is described below. During
digital operation some functions are not available, they are not needed because
of the digital transmission technology being used.
Adjusting the brightness and contrast
Call up theBrightness/Contrastsetting window
Brightness
Set the brightness of the display
With this function you change the brightness of the background lighting.
Contrast
Set the contrast of the display
With this function you modify the contrast of bright colour tones.
Black level
Set the brightness of the display
With this function you modify the contrast of dark colour tones.
Auto level
Adjust the signal level
With this function you can automatically set the contrast.
The function is executed with the
SELECT / MENUbutton.
If the contrast is set too high, bright surfaces can no longer be distinguished from very
bright surfaces. If the contrast is set too low,the maximum brightness will not be achieved.
Adjusting the picture size and position
Call theImage adjustsetting window
Phase
Eliminate picture disturbance
With this function youfine-tune your monitor to eliminate picture disturbance.
Clock
Set synchronisation
With this function you adjust the picture width to eliminate vertical picture
disturbances.
H-Position
Adjust the horizontal position
With this function you move the picture to the left or to the right.
V-Position
Adjust the vertical position
With this function you move the picture up or down.
18 A26361-K1338-Z220-1-7619, edition 1
 
						

							Operation
Adjusting the volume
Call theAudiosetting window
Vo l u m e
Set the volume for playback with the integrated loudspeakers
Mute
Switch the loudspeakers off or on
Setting the colour temperature and colours
Call theColoursetting window
Select the colour temperature
The warmth of the screen colours is set using the colour temperature. The
colour temperature is measured in Kelvin (K). You can choose between
sRGB,6500 K,7500 K,9300 K,NativeandCustom Colour.
In the user-defined setting you can change the colour ratios of the basic
colours (red, green, blue) as required.
Adjusting the display of the OSD menu
Calling theOSD Setupadjustment window
Language
Selecting the language for the OSD menu
With this function you choose between English (default setting), Spanish,
French, Russian, German, Dutch, Italian or Swedish as the language for
the OSD menu.
OSDH position
Setting the horizontal position of the OSD menu
With this function you can move the OSD menu to the left or to the right.
OSDV position
Setting the vertical position of the OSD menu
With this function you can move the OSD menu up or down.
OSDTimeout
Setting the display duration of the OSD menu
With this function you can select a value from 10 to 120 seconds.
If the set time expires without a setting being made, the OSD menu is
automatically hidden.
A26361-K1338-Z220-1-7619, edition 1 19
 
						

							Operation
Configuring function settings in the Advanced menu
Open theAdvancedsettings window
DDC/CI
Activate/deactivate the DDC/CI function
On= The DDC/CI function is activated (standard setting)
Off= The DDC/CI function is deactivated
Resolution Notifier
Monitor information. The optimum resolution for this monitor is 1280 x 1024
pixels.
When the function is active (On), a message will appear on the monitor after
approx. 30 seconds if a different resolution is set.
Change the resolution to 1280 x 1024 to achieve optimum picture quality.
When the function is deactivated (Off), no messages will appear.
Factory Recall
Activate the factory settings
This function is used to reset all settings to the factory settings. The user is
not prompted to confirm the changes.
Press the
SELECT/MENUbutton to activate the function. TheAuto
Processingmessage will be displayed.
Displaying information
Call theInformationsetting window
With this function the model designation, serial number, resolution, H/V
frequency, input signal and polarity of the synchronisation signal are
displayed.
20 A26361-K1338-Z220-1-7619, edition 1
 
						

							Notes on ergonomic colour adjustment
Notes on ergonomic colour adjustment
If you select colours for the monitor in your application programmes,
take note of the information below.
The primary colours blue and red on a dark background do not produce the minimum
required contrast of 3:1 and are therefore not suitable for continuous text and data entry.
When using several colours for characters and background and giving the primary colours full
modulation, you can obtain very suitable colour combinations (see the following table):
Characters
Background
black white purple bluecyan green
yellow red
black++-
+++-
white+++---
+
purple++-- -- -
blue-
+-
+-
+-
cyan
+--
+-- -
green
+--
+---
yellow+-
++--
+
red-
+--- -
+
+ Colour combination very suitable
- Colour combination not suitable because colour hues are too close together, thin characters
are not identifiable or rigorous focusing is demanded of the human eye.
A26361-K1338-Z220-1-7619, edition 1 21
 
						

							Troubleshooting
Troubleshooting
Should an error occur,first check the following points. If the distortion is still not eliminated,
the monitor should, if possible, be checked on another computer.
If you cannot solve the problem, please contact our Service Desk.
Having this problem? Check the following points:
No screen display
Power indicator does not light up►Check whether the ON/OFF switch on the
monitor is switched on.
►Check whether the power cableon the
monitor is connected correctly.
►Check whether the computer is switched on.
No screen display
Power indicator is lit►Check whether the computer is switched on.
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Press any key on the computer keyboard.
The computer may be in power saving
mode.
►Alter the brightness and/or contrast until you
get a picture.
Message:No Signal
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Check whether the computer is switched on.
Message:
Frequency out of range:
## kHz / ## Hz
Please change the display mode
to 1280 x 1024 with 60 HzThe input signal (horizontal frequency and
refresh rate) at the displayed input does not
correspond to the technical data for the monitor.
►Adjust the video frequency range using the
computer software (see documentation for
the computer or display adapter).
►Set a different screen resolution using the
computer software (see documentation for
the computer or displayadapter).
Picture position not correct
The monitor recognises an undefined mode (see
chapterTechnicaldata,Page25).
►Press the
EXIT / AUTObutton to perform
auto-adjustment of the screen.
Picture is shaking
►Check whether the data cable for the
monitor is correctly attached to the monitor
port on the computer.
►Press the
EXIT / AUTObutton to perform
auto-adjustment of the screen.
Picture is wrongly adjusted►Press theSELECT / MENUbutton to
activate theFactory Recallfunction.
TheAuto Processingmessage appears.
22 A26361-K1338-Z220-1-7619, edition 1