Fujifilm Camera X100t Owners Manual

Connect the camera to the computer using the supplied USB cable and copy pictures as
described below.
Start the computer.
1. 
Turn the camera off.2. 
Use the supplied USB cable to connect the camera and computer.
Be sure the connectors are in the corr ect orientation and fully inserted. Connect
the camera directly to the computer ; do not use a USB hub or keyboard.
3. 
Turn the camera on.4. 
Copy pictures to the computer using MyFinePi x Studio or applications provided with your
operating system.5....

If a memory card containing a large number of images is inserted, there may be a delay
before the software starts and you may be unable to import or save images. Use a
memory card reader to transfer pictures.
Make sure that the computer does not display a message stating that copying is in
progress and that the indicator lamp is out before turning the camera off or
disconnecting the USB cable (if the number of images copied is very large, the indicator
lamp may remain lit after the message has  cleared...

If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without fi rst being copied to a computer.
Connecting the Camera
Printing Selected Pictures
Printing the DPOF Print Order
Printing Pictures via USB
002D0020 0032003500330020 002D  

Connect the USB cable as shown and turn the printer on.1. 
Turn the camera on. [USB] will be displayed in the monitor, followed by the PictBridge
display.2. 
Printing Pictures via USB
002D0020 0032003500340020 002D  

Press the selector left or right to display a picture you wish to print.
To print one copy of th e current picture, proceed directly to Step 3.1. 
Press the selector up or down to choose th e number of copies (up to 99). Repeat steps
1–2 to select additional pictures.2. 
Press  [MENU/OK]  to display a confirmation dialog.3. 
Press [MENU/OK]  to start printing.4. 
If no pictures are selected when the  [MENU/OK] button is pressed, the camera will
print one copy of the current picture.
Printing the Date  of...

To print the print order created with [PRINT ORDER (DPOF)] in the playback menu.
In the PictBridge display, press  [DISP/BACK] to open the PictBridge menu.
1. 
Press the selector up or down to highlight  [PRINT DPOF].2. 
Press [MENU/OK]  to display a confirmation dialog.3. 
Press [MENU/OK]  to start printing.4. 
Printing Pictures via USB
002D0020 0032003500360020 002D  

During Printing
A message is displayed during printing. Press [DISP/BACK] to cancel before all pictures
are printed (depending on the printer, printing may end before the current picture has
printed). If printing is interrupted,  turn the camera off and then on again.
Disconnecting the Camera
Confirm that the above message is not displaye d and turn the camera off. Disconnect the
USB cable.
Pictures can be printed from internal  memory or a memory card that has been
formatted in the camera.
When pictures...

To show pictures to a group, connect the camera to a TV using an HDMI cable (available
separately from third-party suppliers; note that the TV can only be used for playback, not
shooting).
Turn the camera off.
1. 
Connect the cable as shown below.
Insert into Micro HDMI connector
Insert into HDMI connector
Use an HDMI cable no more than 1.5  m (4.9 ft.) long.
Be sure the connectors are fully inserted.
2. 
Tune the television to the HDMI input channe l. See the documentation supplied with the
television...

Shoe-mounted flash units
Power Supplies
Remote Releases
Conversion Lens
Stereo microphones
Other
Website of the country or region of purchase
For more information, visit the website of the country or region of purchase (the new window
will open).
Check the website »
Accessories
002D0020 0032003500390020 002D  

EF-20
EF-42
EF-X20This clip-on flash unit (powered by two AA batteries) has a Guide Number of
20/65 (ISO 100, m/ft.) and supports TTL flash control. The flash head can be
rotated upwards 90° for bounce lighting.
This clip-on flash unit (powered by four AA batteries) has a Guide Number of
42/137 (ISO 100, m/ft.) and supports TTL  flash control and auto power zoom in
the range 24–105  mm (35 mm format equivalent). The flash head can be rotated
90° up, 180° left, or 120° right for bounce lighting.
This...