Ford Mustang Owners Manual

Action and Description
Message
If you wish to arm the alarm with full guard, leave your vehicle
without pressing the OK button.
Note: Selecting reduced guard does not set the alarm permanently to reduced guard. It
sets it to reduced guard only for the current locking cycle.
Arming the Alarm
To arm the alarm, lock your vehicle.  See
Locks
 (page 40).
Disarming the Alarm
Disarm and silence the alarm by unlocking
the doors and switching your vehicle on or
unlocking the doors with the remote
control.
Note: A...

Any further attempts to perform one of the
above sounds the alarm again.
Full and Reduced Guard
Full Guard
Full guard is the standard setting.
In full guard, the interior sensors are on
when you arm the alarm.
Reduced Guard
In reduced guard, the interior sensors are
off when you arm the alarm.
Selecting Full or Reduced Guard
You can select full or reduced guard using
the information display.  See General
Information (page 67).
Ask on Exit (If Equipped)
You can set the information display to ask
you each...

ADJUSTING THE STEERING
WHEEL
WARNING
Do not adjust the steering wheel
when your vehicle is moving.
Note:
Make sure that you sit in the correct
position.  See Sitting in the Correct
Position (page 91). 1. Unlock the steering column.
2.
Adjust the steering wheel to the desired
position. 3. Lock the steering column. AUDIO CONTROL
You can operate the following functions
with the control:
Volume up.
A
Seek up or next.
B
Volume down.
C
Seek down or previous.
D
Media.
E
MEDIA
Press repeatedly to scroll through...

VOICE CONTROL
End a call.
A
Answer a call.
B
Voice recognition.
C
Mute.
D
See your SYNC information.
CRUISE CONTROL See Cruise Control (page 127). INFORMATION DISPLAY
CONTROL
See 
Information Displays (page 67).
50
Mustang (CZG) Vehicles Built From: 13-07-2015, GR3J 19A321 AKA enGBR, Edition date: 06/2015, First Printing Steering WheelE174584
C
D
B
A E174594 E174595  

WINDSHIELD WIPERS
Note:
Fully defrost the windshield before
switching on the windshield wipers.
Note: Make sure you switch off the
windshield wipers before entering a car
wash.
Note: Clean the windshield and wiper
blades if they begin to leave streaks or
smears. If that does not resolve the issue,
install new wiper blades.
Note: Do not operate the wipers on a dry
windshield. This may scratch the glass,
damage the wiper blades or cause the wiper
motor to burn out. Always use the
windshield washers before...

Highest sensitivity
A
OnB
Lowest sensitivity
C
Use the rotary control to adjust the
sensitivity of the rain sensor. There are six
sensitivity settings. When you set the
control to low sensitivity (the first
position), the wipers turn on when there is
a large amount of moisture on the
windshield. When you set the control to
high sensitivity (the sixth position), the
wipers will turn on when there is a small
amount of moisture on the windshield.
Keep the outside of the windshield clean.
The rain sensor is...

GENERAL INFORMATION
Condensation in Lamp Assemblies
Exterior lamps have vents to
accommodate normal changes in air
pressure.
Condensation can be a natural by-product
of this design. When moist air enters the
lamp assembly through the vents, there is
a possibility that condensation can occur
when the temperature is cold. When
normal condensation occurs, a fine mist
can form on the interior of the lens. The
fine mist eventually clears and exits
through the vents during normal operation.
Clearing time may...

Headlamp Flasher
Pull the lever toward you slightly and
release it to flash the headlamps.
AUTOLAMPS
WARNING
The autolamps switch position may
not activate the headlamps in all low
visibility conditions, such as daytime
fog. Always ensure that your headlamps
are switched to auto or on, as appropriate,
during all low visibility conditions. Failure
to do so may result in a collision. When the lighting control is in the
autolamps position, the headlamps
automatically turn on in low light situations
or when...

INSTRUMENT LIGHTING
DIMMER
Note:
You disable the manual dimmer
when you adjust the setting to Auto
Dimming in the information display.  See
Information Displays (page 67).
Note: If you disconnect the battery or it
becomes discharged, the illuminated
components will switch to the maximum
setting. Press repeatedly or press and hold until
you reach the desired level.
HEADLAMP EXIT DELAY
After you switch the ignition off, you can
switch the headlamps on by pulling the
direction indicator lever toward you....

REAR FOG LAMPS
Press the control to switch the fog lamps
on or off.
You can only switch the rear fog lamps on
when either the front fog lamps or low
beam headlamps are on.
Note:
Only use the rear fog lamps when
visibility is less than 164 feet (50 meters).
Note: Do not use the rear fog lamps when
it is raining or snowing.
Note: If you switch autolamps on, you can
only switch the fog lamps on once
autolamps has turned the headlamps on. HEADLAMP LEVELING
1. Press to release the pop out button. 2. Rotate...