Faroudja Fdp-Dila3 Instructions

							51

 Model name/Article name  FDP-DILA3 THEATER OPTIMIZED PACKAGE

 Emission method D-ILA®* (Reflective Active Matrix Principle)

 Display panel/ size D-ILA /0.7 (1400pixels x 1050pixels) x 3 (Total number of pixels: 4,410,000)

  Projecting lens  x 1.3 zoom lens (2.1: ~2.6:1)  (Manual zooming and focusing)


  Light-source lamp 250W Ultra High Pressure Mercury lamp
[Part No.: BHL5006-S/Rating: 250W]

 Screen size  40 ~ 200 

 Projection distance  Approx. 1.6m ~ 12m

  Color system  NTSC/PAL via external Video Processor

  Resolution 1400 dots x 1050 dots (S-XGA full resolution, during RGB input)
1000 TV lines (Horizontal resolution, aspect ratio 4:3, during video input)

  Scanning frequency Horizontal frequency : 15kHz~120kHz
Vertical frequency : 50Hz~120Hz


  Input terminals VIDEO IN Y/C 1-line, mini DIN 4 pin x 1
Y: 1.0 Vp-p, 75ohm C:0. 286 Vp-p, 75ohm(NTSC), 0.3Vp-p, 75ohm(PAL)
VIDEO 1-line, RCA pin x 1 1.0V(p-p),75ohm,synchronised
PC 1 1-line, D-sub 3-rows 15 pin x 1
PC 2 1-line, BNC x 5
Y, CB,CR : Component (Y, B-Y, R-Y) signal (Color Difference signal)
Y,  PB, PR : DTV-format (Y, P
B, PR) signal
R, G, B : Analog RGB signal
H/Cs, V : Horizontal (H) sync/composite (Cs) sync, Vertical (V) sync signal
PC3 1-line, DVI-D (single-24pin) terminal
A UDIO 1-line, RCApin X 1 (Y/C, VIDEO, PC1, PC2, PC3) 0.5V(rms), high impedance
CONTROL RS-232C : 1-line, D-sub 9pin x1 (External controller)
REMOTE : 1-line, stereo mini-jack x1 (remote control)

  Output terminals DC OUT 5V, 1.5A DC Power Jack

 Power requirements AC 100V ~ 240V AC, 50Hz/ 60Hz

  Power consumption 3.4 A (100V AC) ~ 1.42A (240V AC)

  Operation environment Temperature: 41°F ~ 95°F (+5°C ~ +35°C)
Humidity: 20% ~ 80% (no condensation.)
(Preservation temperature    14°F ~ 140°F  (–10°C ~ +60°C))


 Dimensions (Width x Height x Length) Approx.  16.57”x approx.  6.67”x  approx.  18.8” 

  Mass Approx. 28.0lbs 
 
Specifications
•D-ILA® is the abbreviation for Direct drive Image Light Amplifier.
• Design and Specifications are subject to change without notice.
• D-ILA
® devices are manufactured with a very high-precision technology. Pixel effectiveness is 99.99%. Only 0.01% or less of the
pixels would either not light up or remain permanently lighted up.
•F or easy understanding, pictures and illustrations may be emphasized, composed or have omissions and may be more or less
different from the actual products.
• All brand names and products (IBM, Macintosh) herein are the trademarks or registered trademarks of their respective compa-
nies.
• This product conforms to the ‘Household electric appliances and general-purpose articles harmonics control measure guideline.’ 
						

							Dimensions (unit: Inches)
Specifications
6M (Depth 10mm)
An attachment screw should be of a 
length more than 6mm and less than 10mm.D1 Center of lens
18120
67.5
38.2 298300A
52 
						

							53
4
2
9
8
16
876
54321 3
1
11 12 13
6712 10 9
45
3
815
14
24
7
15
23
6
14
22
3
11
19
2
10
18
5
13
21 4
12
20
1
9
17
Specifications
Pin arrangement

  Y/C terminal
Pin number Signal name
1 GND (Y)
2GND (C)
3Y
4C
Pin number Signal name
1N/C
2RD
3TD
4N/C
5 GND
Pin number Signal name
6N/C
7N/C
8N/C
9N/C

 RS-232C IN/OUT terminal

  PC 1 terminal

  PC 3 terminal
Pin number Signal name
1 Red
2Green
3 Blue
4N/C
5N/C
6GND (Red)
7GND (Green)
8 GND (Blue)
Pin number Signal name
9N/C
10 GND (SYNC)
11 GND
12 N/C
13 H.SYNC
14 V.SYNC
15 N/C
Pin number Signal name
1 TMDS data 2 -
2 TMDS data 2 +
3TMDS data 2 /4 shield
4N/C
5N/C
6 DDC clock
7 DDC data
8N/C
9TMDS data 1 -
10 TMDS data 1 +
11 TMDS data 1/3 shield
12 N/C
Pin number Signal name
13 N/C
14 TMDS +5V power supply
15 Earth (+5V)
16 Hot plug detection
17 TMDS data 0 -
18 TMDS data 0+
19 TMDS data 0/5 shield
20 N/C
21 N/C
22 TMDS clock shield
23 TMDS clock +
24 TMDS clock -
TMDS = Transition Minimized Differential Signaling
DDC = Display Data Channel 
						

							Specifications

 RS-232C external control
By connecting a computer to the projector with a RS-232C cross cable (D-sub 9 pins), you can control the projector with the
computer. The commands to control the projector and the response data format against the received commands are explained
here.
For details, please consult the authorized dealer where you purchased your projector.
1. Communication Specifications
The communication specifications are as follows.
Baud rate 9600bps/19200bps
Data length 8 bits
Pa rity None
Stop bit 1 bit
Flow control None
2. Command Format
2-1 Command data format
When sending a control command to the projector, use the following data format.
HeaderIDSPParameterCommandSP
CR[[
Header : Designates the head of data and the data type.
: ‘!’ (21h): Assigns command to the projector
: ‘?’ (3Fh): Query to the projector (Asking command)
ID : ‘1’: The identification number of the projector. (Manufacturer set value ‘1’)
SP : Designates the delimiter for ID, Command, and Parameter. (20h)
CR : Designates the terminal of the data. (0Dh)
* [  ] is not necessary for Asking command.
2-2 Response data format
Upon executing the received control command, the projector sends back the following response data to the computer.
HeaderIDSPParameterNormal Termination  StatusSP
CR[[
Header : Designates the head of data.
: ‘@’ (40h): Fetches data from the projector.
ID : ‘1’: The identification number of the projector. (Manufacturer set value”1”)
SP : Designates the delimiter for ID, Command, and Parameter. (20h)
Normal Termination Status : ‘0’  (30h)
CR : Designates the terminal of the data. (0Dh)
2-3 Parameters used for the data format The following three kinds of parameters are used for control commands and response data.
1)  Numeric value
2)  ON/OFF
3)  Special parameters
Each parameter is as follows:
1) Numeric value
A 2-byte hexadecimal value (sign included) is represented by a set of 4 digit (4 bytes) characters.
Designated range: ‘8000’ to ‘7FFF’.
2) ON/OFF Shows the status (ON/OFF) of the projector, such as POWER and HIDE.
Character Hex. Meaning
‘0’ 30 OFF
‘1’ 31 ON
54 
						

							Specifications
3) Special parametersInput switching parameters
Character Hex. Meaning
‘0’ 30 Y/C
‘1’ 31 VIDEO
‘3’ 33 PC1
‘4’ 34 PC2
‘5’ 35 PC3
Operation mode parameters
Character Hex. Meaning
‘0000’ 30h 30h 30h 30h Stand-by mode
‘0001’ 30h 30h 30h 30h Power-on mode
‘0002’ 30h 30h 30h 30h Cool-down mode
‘0004’ 30h 30h 30h 30h Emergency mode
Function CommandAsking Data type
Power on ELSENumeric ValueON/OFF Special Data
OPERATE U0F X X XX
HIDE U00XXX
Right Left reversalU17XXX
Top Bottom inversionU18XXX
Input switch U1AXX XY/C ...
Operation modeZ03XX Stand-by…
Operation mode: Only Asking command is possible
3. External control command table
55 
						

							56
FAROUDJA WARRANTY STATEMENT 
 
Faroudja®, a division of Genesis Microchip Inc.  warranties that its products will substantially 
conform to published specifications, subject to the terms and conditions below. These  warranties 
are limited to the first purchaser of the products (“Purchaser”)for the period listed below from the 
date of sale. 
 
Video Processors:   Two (2) years limited parts and labor 
DVD Drives:    One (1) year limited parts and labor 
Plasmas (HD20 version): Four (4) years limited parts and labor (Image burn-in is not covered) 
Projectors:   
DILA3 and DLPHD20   Two (2) years limited parts and labor (Image burn-in is not covered) 
DILA2     Three (3) years limited parts and labor (Image burn-in is not covered) 
 
These limited warranties are contingent upon proper use and installation and does not apply to 
products damaged as a result of accident, misuse, neglect, alteration, improper installation, 
unusual physical or electrical stress or unauthorized repair. Image burn-in on display devices is 
not covered under warranty. See individual product warranty statement for warranty limitations. 
All warranty claims should be made at the place of purchase. No products may be returned to 
Faroudja without its consent. If requested by Faroudja, Purchaser must provide proof of purchase 
and return defective products to Faroudja with the appropriate Return Material Authorization 
(RMA) completed, a Faroudja RMA number assigned and transportation charges prepaid. 
Warranty may be void if unit is not returned to Faroudja Service in the original shipping carton.
 
 
 
Should a product fail to conform to the warranty above, then Faroudja shall, at Faroudja’s sole 
option, (i) repair the non-conforming product or portion thereof, provided that the product is returned 
to Faroudja within the warranty period in accordance with the return procedures set forth above, or  
(ii) provide Purchaser with replacement for the non-conforming product or portion thereof. The 
preceding sentence states Faroudja’s entire liability and Purchaser’s exclusive remedy with respect 
to breach of the warranty.   
 
 
THE FOREGOING WARRANTIES ARE IN LIEU  OF ALL WARRANTIES EXPRESSED, IMPLIED 
OR STATUTORY, REGARDING THE PRODUCTS, AND ALL IMPLIED WARRANTIES, 
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY 
OR FITNESS FOR A PARTICULAR PURPOSE AND ANY OTHER WARRANTY OBLIGATIONS  ON THE PART OF FAROUDJA OR GENESIS MICROCHIP INC. IN NO EVENT WILL 
FAROUDJA OR GENESIS MICROCHIP INC. BE LIABLE FOR LOSS OF PROFITS OR  GOODWILL, OR DIRECT, INDIRECT, INCIDENTAL, CONSEQUENTIAL OR SPECIAL 
DAMAGES OF ANY KIND, HOWEVER CAUSED, WHETHER BY FAROUDJA’S BREACH OF 
WARRANTY OR BY FAROUDJA’S SOLE OR 
CONCURRENT NEGLIGENCE OR OTHERWISE. 
 
FAROUDJA may change product specifications and warranty policy at any time 
without notice. The Warranty policy outlined above effective September 1, 2003. 
 
Our most current warranty policy can be viewed online at www.faroudja.com/warranty
. 
  Faroudja  
750 Palomar Ave., Sunnyvale, California 94085  Tel: 408-735-1492 Fax: 408-735-8571 
www.faroudja.com 
A division of Genesis Microchip Inc.  
  
						

							FDP-DILA3      
®  THEATER OPTIMIZED PACKAGE
Printed in USA
© 2003 FAROUDJA