Faroudja Fdp-Dila3 Instructions

							21
RPR/CRGYBPB/CSVDVIH/CS
PC1PC3PC2
AUDIO INREMOTEDC OUT
5V  }1.5A RS-232C OUT RS-232C IN Y/C VIDEOCONTROLVIDEO IN
P
ersonal Computer connector cable (supplied)
Right side of projector
Desktop type (DOS/V, PC-9800 etc.) Video Processor
Desktop type 
(Macintosh)
Notebook Type
Desktop type To  
PC1 To DVI
To  PC2
To monitor 
connector
To  monitor 
connector
Conversion 
adapter for MAC 
(separately available)
To
 monitor 
connector Separated cable 
(separately available)
❈
There are some notebook type computers that do 
not allow the computer’ s LCD to work if an external 
display device is connected. With such computers, 
the LCD display and external display output need to 
be switched.
Connecting to Various Devices

  Connecting to Computers
•Please read thoroughly the manual that comes with the computer devices
• Use the supplied computer connection cable. Also prepare cables for connecting the devices.
• When the PC2 input terminal is used, “PC2 (BNC)” must be selected from the
“Options”  menu. 
• DVI computer can also be pass-through video processor 
						

							22
Notebook type
Connect to Computer Connect to the IN 
terminal of third projector
RS-232C connection cable 
(separately available)
(Cross cable)
Projector
Second projector
RPR/CRGYBPB/CSVH/CS
PC1PC2
A UDIO INREMOTEDC OUT
5V  }1.5A RS-232C OUT RS-232C INCONTROL
BPB/CSVH/CS
PC1PC2
NREMOTERS-232C OUT RS-232C INCONTROL
BPB/CSVH/CS
PC1PC2
INREMOTERS-232C OUT RS-232C INCONTROL
RS-232C connection cable (separately available) 
(Cross cable)
Connection for controlling more than one projector
By using the CONTROL terminal, more than one projector can be controlled simultaneously by one computer.
Connect the OUT terminal of the first projector to the IN terminal of the second projector, then connect the OUT terminal 
of the second projector to the IN terminal of the third projector. Connect these projectors in series.
Connecting to Various Devices


 Control from external device
•It is possible to control the projector with a computer by connecting the computer to the CONTROL RS232C IN terminal of the
projector.
❈ Please request the connection cable from us if needed.
❈  For more information, please go to your authorized dealer. 
						

							23
Power cord (supplied)
2
1
Connecting to Various Devices
1.Connect the supplied power cord to the power input ter-
minal of the projector.
2.Insert the main plug of the supplied power cord into the
wall outlet.
After all devices have been connected, connect the supplied power cord.
Connecting the Power Cord (supplied)
Cautions Against Fire and Electric Shock
● 
Since the power requirement of the projector is high, please insert the power plug directly into a wall outlet.
●  When not using devices, remove the power cords from the wall outlets.
●  Do not use power cords other than those supplied.
●  Do not use a power voltage different from that which is indicated.
●  Do not cut, tear or modify the power cords. Also, do not put a heavy object on, heat, or stretch the power cords, otherwise the y
may be damaged.
●  Do not insert or pull out the plugs with a wet hand.
(eg.) 
						

							24
MENU
V-KEYSTONE PC
LAMP
H-KEYSTONE VOL. EXIT
ENTER
VIDEO
TEMPSTAND BYOPERATE
1-2
2
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
1-2
2
LAMP TEMP STAND BYOPERATE
Light on
  Projector: Indicator part
LAMP TEMP STAND BYOPERATE
Light on
OPERATEOPERATE
Projector: 
Control panel
Remote control 
unit
Projector : Indicator
Basic Operations
Note
•
Messages are displayed in the language set
by  the user in the “Language” menu. The pre-
set language upon purchase  is “English”.  The
user can choose from 8 national languages.
However, the input mode (PC 1, PC 2, PC 3,
Y/C, VIDEO) and button indications (FREEZE,
D .ZOOM, EXIT) are only displayed in English
irrespective of the display language setting.
Basic Operation Procedures
Once the basic settings are done, follow the procedures below:
1.Po wer On
1The STAND BY indicator lights up when the power cord is
connected.
2Press the OPERATE button on the projector (or the OPER-
ATE button on the remote control unit) for one second or
more.
The OPERATE indicator lights up and the projected screen ap-
pears slowly.
2.Selecting the image to be projected

 When you select an image device to be connected to the
VIDEO IN (VIDEO or Y/C) terminal: press VIDEO.
Each time you press either button, the selected input changes as
f ollows.
Notes
• Upon projection, the image may flicker for a few seconds, but
this is not a malfunction.
• When the lamp is turned on, it will slowly become brighter. It
will take more than a minute for the brightness to stabilize.
VIDEO : Image from the input VIDEO ter-
minal on the right hand side of pro-
jector will be projected.
Y/C : Image from the input Y/C terminal on the right hand side of the pro-
jector will be projected.
If projector set up is not yet complete, please read ‘Adjustments and Settings Using Menus’  on page 31  and perform the necessary
settings.
VIDEO
VIDEO
Projector: 
Control panel Remote Control 
Unit 
						

							25
PC 1
PC 2
PC 3
Y/C
VIDEO
A udio-Vol 12
Digital Zoom x12
Vert.Keystone
0
Horiz.Keystone
0
3.
4.
Tele side
Wide side Near side
F ar side
Basic Operations

  Display using the direct buttons
The direct buttons enable direct switching and
operation without having to go through the
menu.
Input mode can be selected by
pressing the PC button or the
VIDEO button.
When the DIGITAL ZOOM, VOLUME, V-KEYSTONE
or H-KEYSTONE button is pressed, a level bar of
the function is displayed.VIDEO
Screen display
PC
PC
Projector: 
Control Panel Remote Control 
Unit
PC1 PC2 PC3
PC1
Screen display
When “Line display”
 (☞  page 38)
is set to “5 sec” : After changing an
input , the new selection will ap-
pear on the screen for about 5 sec-
onds.

When selecting a computer or other devices connected
to PC1, PC2 or PC3 : Press PC
Upon pressing the button, the input mode changes  as follows.
PC1 : Projects image from PC1 input terminalon the right hand side of the projector.
PC2 : Projects image from PC2 input terminal on the right hand side of the projector
PC3 : Projects image from PC3 input terminal
on the right hand side of the projector.
When “Line display” ( ☞ page 39)
is set to “5 sec”: after changing an
input, the new selection will appear
on the screen for about 5 seconds.
Notes

• When no image is input to the selected input terminal, the mes-
sage “No Input”  is displayed on the screen.  ( ☞  page 4
8)

• When the PC2 input terminal is used, “PC2(BNC)” must be se-
lected from the “Options”  item in the main menu.  (
 

☞ page 3
8)
3. Adjusting the Zoom Ring (the screen size)

  To  enlarge the screen size:  Turn the zoom ring towards the ‘Wide’
side.

 To reduce the screen size: Turn the zoom ring towards ‘Tele’ side.
4. Adjusting the Focus Ring(Focus) 

 To focus on nearer points: Turn the focus ring towards the ‘Near’
side.

 To focus on farther points: Turn the focus ring towards the ‘Far’
side.
.
Remove top cover to access
Remove top cover to access 
						

							26
MENU
V-KEYSTONE PC
LAMP
H-KEYSTONE VOL. EXIT
ENTER
VIDEO
TEMPSTAND BYOPERATE
5
OPERATE
OPERATE
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
5
V OL.VOLUME
Projector: 
Control panel Remote Control 
Unit
LAMP TEMP STAND BYOPERATE
Tu r n
 on
Tu r n  off
OPERATEOPERATE
Projector: 
Control Panel Remote Control 
Unit
Projector: Indicator part
Basic Operations
5.Adjusting the Sound Volume


 To  increase the volume: press VOLUMEª  (0  ➞  50)

  To  lower the volume     : press VOLUME
·  (50  ➞ 0)
When “Menu display”  ( ☞  page 38)
is set to “15sec”, after pressing the
V OLUME button, the sound vol-
ume display will appear on the
screen for about 15 seconds.
(Press EXIT button to immediately
remove the Audio-vol display.)
Note
• When the sound volume is displayed on the screen, pressing
the PRESET button will reset the set value to “0”.
Po wer Off
1.Press the OPERATE button on the projector (or the OP-
ERATE button on the remote control unit ) for  1 second
or more.
The OPERATE indicator will disappear, the STAND BY indicator starts
to blink , and the projector goes into the cool-down mode.
●The STAND BY indicator will continue blinking for approximately 90
seconds as the temperature of the light source lamp cools (Cool
Down Mode)
Note
•The OPERATE button will not work for approximately 1 minute
from when the light-source lamp is turned on. Please use the
button after approximately 1 minute.
Caution
• Please do not pull out the plug from the power source when
the STAND BY indicator is blinking. It will shorten the life of
the lamp and cause malfunction.
Audio-VolScreen display
Audio-Vol 12 
						

							27
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
Digital zoom   X1.2
Direction buttons available
DIGITAL ZOOM
Remote Control 
Unit x 2.0
Digital zoom   X1.2Direction buttons availableDigital zoom   X2Direction buttons available
ENTER
Remote Control Unit
Digital zoom   X1.2Direction buttons availableDigital zoom   X2Direction buttons available
DIGITAL
ZOOM
PRESET
Frequently used Convenient Functions
When an image is projected onto the screen, the following operations
can be performed directly without going through the menu operation.
 DIGITAL ZOOM
 HIDE
 FREEZE
 KEYSTONE
 QUICK ALIGN. (quick alignment)
 SCREEN
Basic Operations
Note
•The quality of the zoomed image is reduced
in comparison with the original one.

  “Digital zoom” Display
1 Magnifying power display
x1.0: 1 time  (standard) x2.0: 2 times
x1.2: 1.2 times x2.5: 2.5 times
x1.4: 1.4 times x3.2: 3.2 times
x1.6: 1.6 times x4.0: 4 times
2Level Display
Level shown is based on selected magnification.
 Enlarging the Image
We  can zoom up while not changing the size of the projected screen.
After zooming, the position of the image displayed can be moved.
● This cannot be done using the projector buttons. Please use the re-
mote control unit.
1.Press DIGITAL ZOOM  ª.
“Digital zoom” display appears on the screen and the projector changes
to the Digital Zoom Mode.
•When pressed,the image on the screen will be enlarged in 8 stages.
(including Standard)
To  reduce the size of the image
When the DIGITAL ZOOM ·button is pressed, the
previously enlarged image will be reduced progres-
sively until it returns to the original size.
To  reduce the image to the original size
When the PRESET button  is pressed, the image will
return to its original size and position.
(Please operate  while “Digital zoom” is displayed.)
2.While “Digital zoom” display appears on the screen, you
can move the zoomed image with the cursor buttons on
the remote control.

 To see the upper part of zoom up image:
Press .

 To see the lower part of zoom up image:
Press 
.

 To see the right part of zoom up image:
Press 
.

 To see the left part of zoom up image:
Press 
. 
						

							28
PRESET
MENUEXIT
ENTER
HIDE
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
HIDE
HIDE
Projector: 
Control Panel Remote Control 
Unit
Digital zoom available
Frozen
FREEZE
“FREEZE” icon
FREEZE
Remote Control Unit
Basic Operations
  Turning Off Image and Sound
Video image and sound can be temporarily turned off.
Press the HIDE button once:
Image and sound turn off.
Press the HIDE button again:
Video Image and audio sound come on again.
Note
•
When the projected image input is changed, the HIDE function is
cancelled and image and sound return.
  Displaying a Still Picture
The projected image can be stilled temporarily.
• This operation cannot be operated by the projector buttons. Please use
the remote control unit.
Press the FREEZE button.
Picture stills after the FREEZE button is pressed for a few seconds and a
message is shown in the center of the screen. An icon indicating the
“FREEZE” mode will be displayed on the top right corner of the screen.
To  de-freeze the image
When you press the FREEZE button again, the image de-freezes and
resumes.
Notes
•After de-freezing the still picture, note that the projector will not
play the picture that comes immediately after. (Should you want to
play the picture that comes immediately after that at which the freeze
b utton was pressed, please pause the picture at the play device
etc.)
• MENU, QUICK ALIGN, H and V KEYSTONE and SCREEN button
cannot function when picture is still.
• The “FREEZE” message will disappear after 5 seconds. To forcibly
clear “FREEZE”, please press the EXIT button. 
						

							29
MENU
V-KEYSTONE PC
H-KEYSTONE VOL. EXIT
VIDEO
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
V -KEYSTONEV-KEYSTONE
Projector: 
Control Panel Remote Control 
UnitProjector: 
Control Panel Remote Control 
Unit
V-
KEYSTONEV-KEYSTONE
H-KEYSTONEH-KEYSTONEH-KEYSTONEH-KEYSTONE
Projector: 
Control Panel Remote Control 
UnitProjector: 
Control Panel Remote Control 
Unit

 
“Vert. Keystone” Display
1 Adjusted value
range:  - 100 ~ 0 ~100
2 Level displayed
level displayed is based on the adjustment value.

 “Horiz. Keystone” Display
1 Adjusted value
range:  -40 ~ 0 ~40
2 Level displayed
level displayed is based on the adjustment value.
Basic Operations
  Removing the Trapezoidal Distortion of the Image
Depending on the angle of projection onto the screen, the image may get
distorted in trapezoid form sometimes.
When installing the projector or screen for the first time, or when rein-
stalling in other rooms, etc., the trapezoid distortion (Keystone) has to be
removed by adjustments.
Press V-KEYSTONE /  to adjust in the vertical direction.
A “Vert. Keystone” display appears on the screen, and the projector goes
into the KEYSTONE MODE.
Press button (
/ ) in the direction that corrects the trapezoid form.
Notes
•The range where the trapezoidal distor tion can be rectified is  30˚
vertically and 10˚ horizontally  with respect to the projector screen.
However, when both are rendered together, the range of effective
rectification will be narrower.
• Depending on the signal inputted, the keystone adjustment range
may narrow or parts of the image may disappear. This is not a mal-
function.
• Interference patterns may appear on the screen when adjusting the
ke ystone. This is not a malfunction.
•T o restore the original s et value, press the PRESET button. (Adjusted
v alue: 0)
Press H-KEYSTONE /  to adjust in the horizontal direction
A “Horiz. Keystone” display appears on the screen, and the projector
goes into the KEYSTONE MODE.
Press button (
/ ) in the direction that corrects the trapezoid form.
Vert. Keystone 1
2
–12
Horiz. Keystone1
2
12 
						

							30
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
QUICK ALIGN.
PC VIDEOVOLUME
PRESET HIDE
ENTER
MENU EXIT
FREEZE
OPERATE
V-KEYSTONEH-KEYSTONESCREENDIGITAL
ZOOM
FOCUS
W
S
Image of 4:3
Setting the 
screen size to [4:3]
Setting the 
screen size to [16:9] Image of 16:9
SCREEN
W
S
SCREEN
WS
16 : 9 4 : 3
Note
(Original image) (Aspect ratio) Image of 4:3 Image of 16:9
(Original image) (Aspect ratio)
●
Selecting      or       according to the input signal will change the pr\
ojected 
image as shown in the following tables.
● Screen size can also be chosen from the “Options menu”. ( ☞ page 37)
12
WS
Screen Pos.
Basic Operations
  Using the Quick Alignment function
The quick alignment function automatically adjusts (sets) the screen set-
tings of the image input from the PC 1 or PC 2 input terminal.
●This can only be performed with the remote control.
Press the QUICK ALIGN (Quick Alignment ) button.
During automatic alignment, “QUICK ALIGN...” appears on the screen,
and disappears after alignment is complete.
Notes
•The “Quick Alignment” function only works when computer
signals are input into the input terminal of either PC1 or PC2. It does not work when the signal is input from the VIDEO IN
terminal(VIDEO or Y/C input terminal).
• The Quick Alignment function.
    The adjustments of “Horiz. disp. pos.” and “Vert. disp. pos.”, “Phase”,
“Tracking”, etc. are automatically carried out.
• Using the Quick Alignment function for quick adjustment.
    Please perform this with a bright still-picture. This function may not
wo rk correctly on a dark picture or a motion-picture.
If adjustment with the Quick Alignment function is not satisfactory,
adjust “Horiz. disp. pos.” and “Vert. disp. pos.”, “Phase” and “Track-
ing” individually.
  Selecting the Screen Size
Press the SCREEN button to select the wide screen size (16:9) or the
standard screen size (4:3).

  Screen size display
Displays when  „ is selected. Move the image
position with the cursor button  or .
1 Adjusted value
range:  -30 ~ 0 ~30
2 Level displayed
level displayed is based on the adjustment value. •
When the screen mode is set to 16:9, UXGA signals cannot be pro-
jected. ( ☞ page 38)
1
212
Screen Pos.