Faroudja Fdp-Dila2 Installation And Operations Manual

							41
Menu Operations 
■Quick Reference Guide for PC Menu Mode
*: Factory set value.
Main Menu in PC Menu Mode (While receiving computer-related signals)
Image adj. → (Refer to page 49)
Contrast: Contrast of the picture image being projected can be adjusted. (–30 to +30, 0*)
Brightness: Brightness of the picture image being projected can be adjusted. (–30 to +30, 0*)
Sharpness: Adjust the outline of letters etc. (1 / 2 / 3 / 4 / 5, 3*)
All reset: Resets above items to the factory set values.
Yes / No
Set up
Tracking: The lateral size and display area of picture image can be adjusted. (–128 to +127)
→ (Refer to page 47)
Phase: Flickering or dim picture image can be adjusted. (0 to 31) → (Refer to page 47)
Position: Video screen position and menu position can be adjusted. → (Refer to page 51)
Disp. Posi. / Menu
Resize: The relationship between the number of pixels (resolution) and the screen can be 
selected.→ (Refer to page 53)
“1:1”: Picture image is projected with its original size.
Panel: Picture image is enlarged to the full size.
Aspect*: Picture image is enlarged while maintaining the original aspect ratio.
Clamp: Selectable clamp position. Normally, set to “BP”. ST / BP*
Color temp.
Color temp.:Adjustable color temperature, Low/Middle* /High.
Will be adjusted to correct reddish or blueish image.
RED:Adjusts the red level. (o to 255, the adjustable range varies depending on signals)
GREEN:Adjusts the green level. (o to 255, the adjustable range varies depending on signals)
BLUE:Adjusts the blue level. (o to 255, the adjustable range varies depending on signals)
All-reset:Reset above items to the factory set values.
Yes/No
Options → (Refer to page 54)
Options 1
Menu display: 15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.) 
Line display: 5sec* (Line display such as “PC1” or “PC2” appears on top right of the screen for 5 
seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not 
appear.)
Lamp time display:
ON*:Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
OFF:Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC 
mode.
Keystone: Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +128, 0*)
Lamp control:
Normal*:Used as a normal lamp.
LPC: Lamp brightness is aLutomatically controlled with time.
LOC:
Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within 
the menu.
Page 2: Press ENTER to enter the “Page 2” submenu.
Flip H: OFF* / ON (Select for upside-down hanging on the ceiling.)
Flip V: OFF* / ON (Select for upside-down hanging on the ceiling.) 
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min]: Selectable sleep times. If no-signal condition continues for the 
period of selected time (Unite: Minutes), the projector enters the 
stand-by mode. 15 / 30 / 60 / OFF*
Page 1: Press ENTER to return to the “Page 1” submenu. 
Language Language for on-screen display. → (Refer to page 46)
Japanese / English* / German / Spanish / Italian / French
Information→ (Refer to page 56)
Input: Shows the terminal name selected by the PC button. (PC1 or PC2)
Switcher:
This display currently has no meaning. (“CH.0” is usually displayed to indicate that it is not being used.)
Resolution: Shows the resolution of the input signal being received. (Horizontal × Vertical)
It may not be displayed correctly with some input signals.
Frequency H: Shows the horizontal frequency of the input signal being received. (    kHz)
Frequency V: Shows the vertical frequency of the input signal being received. (    Hz)
Lamp time: Accumulated used hours of the light-source lamp. 
						

							42
Menu Operations
Basic Menu Operation
When the MENU button is pressed, the projector enters Video or PC menu mode by responding to the input signal being 
received.
Video menu mode:
Enters this mode when video-device-related signals are 
input from the following devices.
•Video devices connected to the VIDEO IN (Y/C, VIDEO 
and COMP) terminals.
PC menu mode:
Enters this mode when computer-related signals are input 
from the following devices.
•A computer connected to the PC 1 terminal.
•A computer connected to the PC 2 terminal, which outputs 
analog RGB, V, H/Cs signals.
•A computer connected to the DVI terminal.
1Press the MENU button.
The main menu is displayed on the screen.
2Press the cursor button 5 or ∞
∞∞ ∞ to 
select an item in the main menu.
3Press the cursor button 3
33 3 or the 
ENTER button to enter the submenu.
The submenu corresponding to the item selected in step 
2 is displayed on the screen.
*When you selected “Information” in step 2, no 
submenu is available.
4Press the cursor button 5 or ∞
∞∞ ∞ to 
select an item in the submenu.
When a “Language” has been selected in step 2, press 
to set the language.
5Press the cursor button 2
22 2 or 3
33 3 to set 
or adjust the value.
When an item which has the “ENTER” message has been 
selected in step 4, press the ENTER button to move to the 
next submenu.
•All reset→(Refer to page 49)
•Position→(Refer to page 51)
•Decoder→(Refer to page 45)
•Keystone→(Refer to page 54)
•Page 1→(Refer to page 54)
•Page 2→(Refer to page 54)
To exit the main menu:
•While the main menu is displayed, press the MENU button.
The main menu disappears and the original picture image 
resumes.
To exit the submenu:
•While the submenu is displayed, press the EXIT button.
The menu returns to the previous menu.
•To exit the menu mode directly, press the MENU button.
The submenu disappears and the original video image is 
restored.
MENUMENU
Remote control unit
Projector
Remote control unit Projector
Remote control unit Projector
Remote control unit
Projector
Remote control unit Projector 
						

							43
Menu Operations 
Basic Menu Operation (Cont.)
■Basic Button Functions in the Menu Mode
■Remote control unit■Projector
■Video menu mode
■PC menu mode
Button Function
MENU Enters the main menu or exits the menu mode.
Cursor button 5/∞Selects an item in the menu. Pressing ∞ or 5 will scroll the item in the menu.
Cursor button 2/3Sets or adjusts the value.
PRESET If pressed while the keystone setting submenu is displayed, the value is set to “0”.
EXIT Returns to the previous menu.
ENTER Used to enter the submenu from the main menu.
Used to enter the next submenu if “ENTER” is displayed in the selected item.
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
S
MENU button
ENTER button
Cursor buttons
5/∞ / 2/3 PRESET button
EXIT button
LAMP TEMPSTAND BY
HIDE
PC
VIDEO
MENU KEYSTONE
PRESET
EXIT ENTEROPERATE
MENU 
button
ENTER 
button
Cursor buttons
5/∞ / 2/3 PRESET
button
EXIT
button
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationContrast
Brightness
Color
Tint
Sharpness
All resetImage adj.
Contrast
Brightness
Color
Tint
Sharpness
All reset12
12
12
12
1
ENTER
Video main menuVideo submenu
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value. Press 5/∞ to select an item.3 or
ENTER
EXIT
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationContrast
Brightness
Sharpness
All reset
Image adj.
Contrast
Brightness
Sharpness
All reset12
12
ENTER
12345
PC main menuPC submenu
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value. Press 5/∞ to select an item.3 or
ENTER
EXIT 
						

							44
Menu Operations
Changing the Color System (Video Menu Mode Only)
This function is available only in Video menu mode.
The menu is only displayed when there is a signal for the AV IN (Y/C, VIDEO and COMP) terminal.
Normally, use the color system in AUTO. If operation in AUTO is unstable, such as color not being shown, set to a dedicated 
color system in accordance with the color system of the video signal being input.
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 1” submenu appears on the screen.
3Select “Decoder” with the cursor button 5 or ∞
∞∞ ∞, and press the ENTER button.
The “Decoder” submenu appears on the screen.
Video submenus
4Set the color system with the cursor button 5 or ∞
∞∞ ∞.
AUTO: Normally, set to “AUTO”. (Factory set value) 
The color system of a video signal being input is automatically identified and displayed in [   ]. 
In [  ], B/W (Black & White), NTSC, NTSC4.43, PAL or SECAM will be displayed. (It is not always displayed.)
For example, AUTO [ NTSC ] shows that the NTSC signal is being received.
NTSC: Dedicated to NTSC.
NTSC4.43: Dedicated to NTSC4.43.
PAL: Dedicated to PAL.
SECAM: Dedicated to SECAM.
5Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Set up 1
Position
Gamma
Aspect ratio
Decoder
Page 2
ENTER
ENTER
ENTER
Decoder
AUTO  [  NTSC  ]
NTSC
NTSC4.43
PA L
SECAM Cinema
4:3 Down
Up
16:9
ENTER
EXIT 
						

							45
Menu Operations 
Changing the Language Display
The on-screen language is set to “English” when shipped from the factory. When you want to change to another language, set 
it as follows.
1Press the MENU button.
The main menu appears on the screen.
2Select “Language” with the cursor button 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Language” submenu appears on the screen.
3Set the language with the cursor button 5 or ∞
∞∞ ∞.
4Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Memo
About language display
Some words in the menu and messages such as “Quick Alignment”, “Keystone”, “VIDEO” and “NTSC” are shown only in 
English. 
Changing the Screen aspect ratio/HDTV format (Video Menu 
Mode Only)
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 1” submenu appears on the screen.
3Select “Set up 2” with the cursor button 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 2” submenu appears on the screen.
4Select “Screen” or “HDTV” with the cursor button 5 or ∞
∞∞ ∞.
5Adjust the Screen aspect ratio or HDTV format with the cursor button 2
22 2 or 3
33 3.
To adjust multiple items, repeat 4 and 5.
6Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Adjustment item  Button  Adjustment content
Screen2 or 3Select according to the aspect ratio of the screen used.
4:3 16:9
HDTV2 or 3Set the number of effective scanning lines. Normally, select 1080i.
1080i: 1035i:
Language
English
Deutsch
Español
Italiano
Français
:Japanese
English : English
Deutsch : German
Español : Spanish
Italiano : Italian
Français : French
Note: for proper operation with the Video Processor and anamorphic lens, the projector
 should stay in the 4:3 mode. Aspect ratio control is operated with the projector. 
						

							46
Menu Operations
Adjusting Tracking/Phase
Normally, tracking and phase adjustments are automatically carried out when a video signal is input to the projector for the 
first time, or when the QUICK ALIGN. button on the remote control is pressed.
However, you can manually adjust the tracking and phase on the menu.
If a wide stripe appears on the screen, adjust the lateral size of the picture image and the display area (tracking adjustment)
so the stripe disappears.
Also, if text projected on the screen appears flickers or appears dim, adjust phase adjustment so it becomes clear.
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 1” (video mode) or “Set up” submenu appears on the screen.
In video mode: Select set up 2 with the cursor ∞ or 5, and press ENTER button.
The “Set up 2” submenu appears on the screen.
Video submenu PC submenu
3Select “Tracking” or “Phase” with the cursor button 5 or ∞
∞∞ ∞.
4Adjust the tracking or phase with the cursor 2
22 2 or 3
33 3.
Adjust the tracking and phase of the picture image being projected. To adjust the phase, first check for correct tracking 
adjustment.
*To adjust multiple items, repeat 3 and 4.
5Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Note
•A dim image could be caused by insufficient adjustment of brightness and contrast. Before adjusting phase, make sure that 
brightness and contrast are correctly adjusted. To adjust them, refer to “Adjusting Picture Quality” on page 49.
Set up 2
Tracking
Phase
Screen
HDTV
Page 1123
12
ENTER
4:3
1030i16:9
1035i
Set up 1
Position
Gamma
Aspect ratio
Decoder
Page 2
ENTERENTER
ENTERCinema
4:3 DownUp
16:9
Decoder is only displayed when there is a signal for the AV 
IN terminal.
Set up
Tracking
Phase
Position
Resize
Clamp123
12
ENTER
STBP
1:1PanelAspect
Adjustment item Button Adjustment content
Tracking2 or 3The picture image shrinks laterally (right-to-left) or extends laterally (left-to-
right). (–128↔ +127)
Phase2 or 3Set to a position where text appears clear. (0 ↔ 31) 
						

							47
Menu Operations 
Set up for Watching Image Software (Video Menu Mode Only)
This unit has a function which allows you to project movies, which were recorded on film, in the best possible conditions.
(Function to convert 2-3 pull-down interlace scans to progressive scans)
Normally use set to AUTO.
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5 or ∞, and press 3 or the ENTER button.
The “Set up 1” submenu appears on the screen.
3Select “Set up 2” with the cursor button 5 or ∞, and press 3 or the ENTER button.
The “Set up 2” submenu appears on the screen.
4Select “Deinterlace” with the cursor button 5 or ∞.
5Select the Deinterlace function mode with the cursor button 2 or 3.
Video: When watching images recorded with a video camera
Film: When watching images recorded on film
AUTO: The setting is changed automatically
6Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Note
•Operates when the signal is an NTSC or PAL interlace signal. Does not operate for other signals. (The menu is not 
displayed when other signals are inputted.) 
						

							48
Menu Operations
Adjusting Picture Quality
In the “Image adj.” submenu, adjust brightness, contrast, sharpness, etc. to obtain the desired picture quality. Note that the 
adjustment items differ in Video menu mode and PC menu mode. 
1Press the MENU button.
The main menu appears on the screen.
2Select “Image adj.” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Image adj.” submenu appears on the screen.
Video submenu PC submenu
3Select the item to be adjusted with the cursor button 5
55 5 or ∞
∞∞ ∞.
*“Color” and “Tint” are shown in Video submenu only.
4Make adjustment with the cursor 2
22 2 or 3
33 3.
*To adjust multiple items, repeat 3 and 4.
*: Factory set value
■To perform All Reset 
•In the Image adj. submenu, select “All reset” with the cursor button 5 or ∞, and press the ENTER button. Then, the “All
reset” submenu appears on the screen.
•Press the cursor button 2 to select “Yes”, and then press the ENTER button. 
•All items in the “Image adj.” submenu are reset to the factory set values and the menu returns to the previous one.
To exit the “All reset” submenu without performing All reset, select “No” with the cursor button 3 and, press the ENTER 
button.
(To be continued on the next page)
Image adj.
Contrast
Brightness
Color
Tint
Sharpness
All reset12
12
12
12
1
ENTER
Image adj.
Contrast
Brightness
Sharpness
All reset12
12
ENTER
12345
Adjustment item  Button  Adjustment content
Contrast2 or 3Gets lower/higher. (–30↔ 0* ↔ +30)
Brightness2 or 3Gets darker/brighter. (–30 ↔ 0* ↔ +30)
Color2 or 3Gets softer/deeper. (–30↔ 0* ↔ +30)
(Video menu mode only)
Tint2 or 3Gets reddish/greenish. (–30 ↔ 0* ↔ +30)
(Video menu mode only)
Sharpness2 or 3Gets softer/sharper.
• Video menu mode: (–5↔ 0* ↔ +5)
• PC menu mode: (1 ↔ 3* ↔ 5)
Note
•When in the PC menu mode, if the resize function in the PC submenu is set to 
“1:1”, the image quality will not change even if the value is changed.
All reset ENTERResets above items to the factory set values. How to operate is mentioned below 
(next page).
Note: Levels are pre-aligned at Faroudja.
However, some fine-tuning for specific 
installations may be required. 
						

							49
Menu Operations 
.
5Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Memo
In some adjustments, the level bar changes according to the set value. (The setting value is also displayed at the left of the 
level bar.)
Adjusting Color temperature
1Press the MENU button.
The main menu appears on the screen.
2Select “Color temp.” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER 
button.
The “Color temp.” submenu appears on the screen.
3Select “Color temp.” with the cursor button 5
55 5 or ∞
∞∞ ∞.
4Adjust the color temperature with the cursor button 2
22 2 or 3
33 3.
Low: Color temperature decreases (image becoming reddish).
Middle: Results in middle color temperature. (Factory set position).
High: Color temperature increases (image becoming blueish).
5Select “RED” or “GREEN” or “BLUE” with the cursor button 5 or ∞
∞∞ ∞.
6Fine adjust the color temperature with the cursor button 2
22 2 or 3
33 3.
To adjust multiple items, repeat 5 and 6.
■To perform All Reset
•In the Color temp. submenu, select “All reset” with the cursor button 5 or ∞, and press the ENTER button. Then, the “All
reset” submenu appears on the screen.
•Press the cursor button 2 to select “Yes”, and then press the ENTER button. 
•All items in the Color temp. submenu are reset to the factory set values and the menu returns to the previous one.
To exit the “All reset” submenu without performing All reset, select “No” with the cursor button 3 and, press the ENTER 
button
7Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Adjustment item  Button  Adjustment content
RED2 or 3Adjusts the red level. (0 to 255)
GREEN2 or 3Adjusts the green level. (0 to 255)
BLUE2 or 3Adjusts the blue level. (0 to 255)
Ye s
Image adj.
All reset?
No
set by Faroudja.Do not readjust. Note: color temperature has been  
						

							50
Menu Operations
Adjusting the Video Screen/Menu Position
The position of the video screen and the menu on the video screen can be adjusted. You can finely adjust the video screen 
position. The menu will move widely on the video screen.
1Press the MENU button.
The main menu appears on the screen.
2Select “Set up” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press 3
33 3 or the ENTER button.
The “Set up 1” or “Set up” submenu appears on the screen.
Video submenu (“Set up 1” submenu) PC submenu (Set up submenu)
3Select “Position” with the cursor button 5
55 5 or ∞
∞∞ ∞, and press the ENTER button.
The “Position” submenu appears on the screen.
4Press the ENTER button to select “Disp.Posi.” or “Menu”.
Disp.Posi. (Display Position):The video screen position (display position) can be adjusted.
Menu:The menu position can be adjusted.
5Press the cursor button 5
55 5,∞
∞∞ ∞,2
22 2 or 3
33 3 to move the video screen (display) or the 
menu.
*Repeat 4 and 5 to move both video screen (display) and menu positions.
*: Factory set value
6Press the EXIT button to return to the previous menu or press the MENU button to 
exit the menu mode.
Set up 1
Position
Gamma
Aspect ratio
Decoder
Page 2
ENTER
ENTER
ENTER
Cinema
4:3 DownUp
16:9
Decoder is only displayed when there is a 
signal for the AV IN terminal.
Set up
Tracking
Phase
Position
Resize
Clamp123
12
ENTER
STBP
1:1PanelAspect
Adjustment item  Button  Adjustment content
Disp.Posi. - H2 or 3The video screen moves to the left or right. (–30↔ +30)
Disp.Posi. - V5 or ∞The video screen moves up or down. (–30↔ +30)
Menu - H2 or 3The menu moves to the left or right. (Left, center*, right)
Menu - V5 or ∞The menu moves up or down. (Top, center*, bottom)
ENTER
Position
Disp.Posi. Menu
12,12Horizontal position
Vertical position