Faroudja Fdp-Dila2 Installation And Operations Manual

							31
Basic Operations 
■Projector’s buttons
■Remote control unitThe following describes the basic procedure for normal use 
of the projector.
1. Turning on the Power
1Turn on the MAIN POWER switch.
ON [ ❙
❙❙ ❙ ]:The main power turns on and the STAND BY 
indicator comes on.
2Press the OPERATE button for one 
second or more.
•The OPERATE indicator lights and the projected 
screen slowly appears.
Notes
•After the power is turned on, the image may be jumbled for 
a few seconds, but this is not a malfunction.
•After the indicator comes on, it can take a minute or so for 
the lamp to warm up and operate consistently.
■Turning off the Power
1Press the OPERATE button for one 
second or more.
•The STAND BY indicator changes to blinking, and the 
projector goes into cool-down mode. The cool-down 
mode will continue for approximately 120 seconds.
Note
•The OPERATE button will not work for approximately 1 
minute from when the light-source lamp is turned on. Use 
the button after approximately 1 minute.
2Turn off the MAIN POWER switch after 
the STAND BY indicator changes to 
steady on.
OFF [‡
‡‡ ‡]:The MAIN POWER switch turns off and the 
STAND BY indicator goes off.
CAUTION
•Do not turn off the MAIN POWER switch during cool-down 
mode (the STAND BY indicator blinking). Turn it off after 
the STAND BY indicator becomes on (stand-by mode).
LAMP
T
EMP
HIDE
PC
VIDEO
MENU KE
YST
O
NE
PRESET
EXI
TENTE
R OPERATEDOW
NU
P
LAMP TEMPSTAND BY
HIDE
PC
VIDEO
MENU KEYSTONE
PRESET
EXIT ENTEROPERATESTAND BY indicator
OPERATE indicator
OPERATE button
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
S
OPERATE button
STAND BY
OPERATE
Projector’s indicator
OPERATESTAND BY
OPERATE
Remote control unitProjector
or
OPERATESTAND BY
OPERATE
Remote control unit
Projector (Blinking)
STAND BY
OPERATE
Projector 
						

							32
Basic Operations
■Projector’s buttons
■Remote control unit
■Language display
The display languages of the menus, direct buttons 
(DIGITAL ZOOM, KEYSTONE, etc) and messages is set to 
“ENGLISH” when the projector is bought. The display 
language can be selected from the following 6 languages: 
“(Japanese)”, “English (English)”, “Deutsch
(German)”, “Español (Spanish)”, “Italiano (Italian)” and 
“Français (French)”. (Refer to page 46.) However, some 
words (VIDEO, NTSC, Quick Alignment, etc) are only 
displayed in English.
2. Select the Input source to be Projected
Press the VIDEO button or the PC button to switch the input.
•Each time you press either button, the selected input 
changes as follows. The selected name appears on the top 
right of the image on the screen for five seconds. (Called 
line display.)
When selecting an image device connected to the 
AV IN (VIDEO, Y/C or COMP) terminal:
Projector
Press VIDEO.
The input mode changes as follows every time the button is 
pressed.
VIDEO ↔ Y/C ↔ COMP
Remote control unit
Press the “VIDEO”, “Y/C” or “COMP” button.
VIDEO: The image from the VIDEO input terminal on the 
side of the unit is projected. 
Y/C: The image from the Y/C input terminal on the side of 
the unit is projected.
COMP: The image from the COMP (Y, R
B/B-Y, PR/R-Y)
input terminal on the side of the unit is projected.
*When there is no signal from the selected input terminal 
(No signal), “No Input” is displayed.
When selecting a device such as a computer 
which is connected to the PC1, PC2 or DVI 
terminal:
Projector
Press PC.
The input mode changes as follows every time the button is 
pressed.
PC1↔ PC2 ↔ DVI
Remote control unit
Press the “PC1”, “PC2” or “DVI” button.
PC1: The image from the PC1 input terminal on the side of 
the unit is projected.
PC2: The image from the PC2 input terminal on the side of 
the unit is projected.
DVI: The image from the DVI input terminal on the side of 
the unit is projected.
*When there is no signal from the selected input terminal 
(No signal), “No Input” is displayed.
[Screen display]
*To show the line display (Y/C, VIDEO, COMP, PC1, PC2 or 
DVI) or not is selectable by the menu. Refer to “Setting and 
Adjusting Other Functions (OPTIONS)” on page 54.
Note
•When no image signal is input to the selected input 
terminal, the message “No Input” is displayed on the 
screen. (Refer to page 67.)
LAMP TEMPSTAND BY
HIDE
PC
VIDEO
MENU KEYSTONE
PRESET
EXIT ENTEROPERATE
PC button
VIDEO button
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
SPC button
VIDEO button
ZOOM button
PC1 PC2
Y/C DVIVIDEO COMP
FREEZESCREENSSCREENSPC
VIDEO
Remote control unit Projector
VIDEO
QUICK ALIGNMENTPC 1
PC 2
COMP
DV I
Y/C
VIDEO
Line Display 
						

							33
Basic Operations 
■Projector’s buttons
■Remote control unit3. Adjust the Screen Size (Zooming)
How to adjust the projected screen size differs depending on 
the lens unit (optional) you are using.
GL-M2910G (without zooming function):
The projected screen size cannot be changed.
GL-M2915SG/GL-M2920ZG/GL-M2930SZG (with 
zooming function):
Adjust the projected screen size with the following buttons on 
the remote control unit.
Note
•The function of GL-M2915SG is to adjust the view angle
zooming by 2%. (For fine view angle adjustment)
To  enlarge the projected screen size
Press the ZOOM W (Wide) button.
To reduce the screen size
Press the ZOOM T (Tele) button.
4. Adjust Focus
Adjust focus with the following buttons on the remote control unit.
To focus on farther points:
Press the FOCUS + button.
To focus on nearer points:
Press the FOCUS – button.
5. Setting the Screen Aspect Ratio
Set in accordance with the screen aspect ratio that will be 
used. When a screen aspect ratio of 16:9 is used, a 4:3 
image can be projected within the screen without using the 
zoom function.
When using a 16:9 screen:
Press the “W” button.
When using a 4:3 screen:
Press the “S” button.
*There is no button on the unit.
*This setting can also be performed from the menu. (Refer 
to page 46.)
•When using a screen with a 16:9 aspect ratio
When set to “S” (4:3)
*If a 4:3 image is projected, some 
parts of the top and bottom of the 
image may not be displayed.
When set to “W” (16:9)
*A 4:3 image will be displayed in full 
in the middle of the screen.
LAMP TEMPSTAND BY
HIDE
PC
VIDEO
MENU KEYSTONE
PRESET
EXIT ENTEROPERATE
PRESET button
EXIT button
QUICK
ALIGN.
PC1 PC2
Y/C DVIVIDEO COMP HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
S
PRESET button
EXIT button SCREEN W/S button
FOCUS +/– button
ZOOM T/W button
DIGITAL
ZOOM
WT
Remote control unit
FOCUSRemote control unit
Remote control unit
SCREENW
SSCREENW
S
Note: for proper operation with the
Video Processor and anamorphic 
lens, the projector should stay in 
the 4:3 mode. Aspect ratio control 
is operated with the Video Processor.
Aspect ratio control for HDTV pass
-through  is controlled by the projector.         
						

							34
Basic Operations
■Projector’s buttons
■Remote control unitTurning off Image (HIDE)
Video image can be temporarily turned off. 
Press the HIDE button once:
Video image instantly turn off.
Press the HIDE button again:
Video image come on again.
Note
•When the projected image input is changed, the HIDE 
function is canceled and the image return.
Removing the Trapezoidal Distortion of 
the Image
If the image projected on the screen is distorted in trapezoid 
form, correct it with the KEYSTONE buttons on the projector. 
When the KEYSTONE button is pressed, “Keystone”
appears on the screen together with the level bar and set 
value (–80 to 128). When “15 sec.” is displayed in the menu, 
“Keystone” will appear in approximately 15 seconds.
When you press the KEYSTONE button:
The trapezoid form is corrected as shown in the figure.
When you press the KEYSTONE button:
The top bottom inverted trapezoid form is corrected as 
shown in the figure.
*To cancel correction and restore the original screen, press 
the PRESET button. (Adjusted value:0)
*Press the EXIT button to immediately remove the keystone 
display.
Notes
•The trapezoidal distortion (keystone) can be adjusted from 
the option menu. (Refer to page 54.) 
•The range of the trapezoidal distortion adjustment is 
approximately 20° in the vertical direction. 
•Interference patterns may appear on the screen when 
adjusting the keystone. This is not a malfunction. 
•Depending on the type of signal, some noise may appear in 
the picture when the keystone is adjusted.
This is not a malfunction.
LAMP TEMPSTAND BY
HIDE
PC
VIDEO
MENU KEYSTONE
PRESET
EXIT ENTEROPERATE
KEYSTONE
/buttons
PRESET
button
EXIT
buttonHIDE
button
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
S
KEYSTONE
/buttons
PRESET button
EXIT button HIDE button
HIDEHIDE
Remote control unitProjector
Keystone 123
KEYSTONE
KEYSTONE
KEYSTONEKEYSTONE
Projected image with trapezoidal distortion
Remote control unit Projector 
						

							35
Basic Operations 
■Remote control unitQuick Alignment Function
(QUICK ALIGN.)
The Quick Alignment function automatically adjusts (sets) 
the screen settings of the image input from the PC1, PC2 or 
DVI input terminals. This can only be performed from the 
remote control.
While projecting an image on the screen, press the QUICK 
ALIGN. button on the remote control.
Quick alignment is conducted to obtain best image.
*During the automatic alignment, “Quick Alignment” appears 
on the screen, and then disappears when the alignment is 
completed.
[Screen display]
Notes
•This only works for the signals input from the PC1, PC2 or 
DVI input terminals. It does not work for the signals input 
from the AV IN terminal (VIDEO, Y/C or COMP input 
terminal).
•The quick alignment function is used to automatically adjust 
the “Horizontal and vertical position”, “Phase” and 
“Tracking” of the projected image.
•When using the quick alignment function to automatically 
adjust the image, use a bright, still-picture. It may not 
function correctly on a dark or motion picture. If the results 
obtained with the quick alignment function are not 
satisfactory, manually adjust the “Horizontal and vertical 
position”, “Phase” and “Tracking” of the projected image.
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
SQUICK ALIGN.
button
QUICK
ALIGN.Remote control unit
Quick Alignment 
						

							36
Basic Operations
■Remote control unit
FREEZE message
FREEZE inhibit message
DIGITAL ZOOM inhibit message
Displaying a Still Picture (FREEZE)
While projecting an image, a still picture is obtained at any 
time by using the FREEZE button on the remote control.
When you press the FREEZE button:
“FREEZE” appears on the screen for a few seconds and 
then the still picture is shown on the screen. Refer to the 
FREEZE message shown on the left of this page.
*To forcibly clear “FREEZE”, press the EXIT button.
When you press the FREEZE button again.
The original image resumes.
Notes
•During freezing, the picture sent from the signal source is 
lost.
•If any of the inoperative buttons (“MENU”, “QUICK ALIGN.”,
“KEYSTONE”) are pressed while displaying a still picture, 
“FREEZE” is displayed on the screen.
•This function will not work with some signal sources 
(UXGA, etc). In this case, the FREEZE inhibit message 
appears for a few seconds, as shown on the left. To forcibly 
clear this message, press the EXIT button.
Zooming a Part of the Image 
(DIGITAL ZOOM T/W)
A part of the image being projected can be digitally magnified up 
to four times. When the DIGITAL ZOOM T or W button is 
pressed, “Digital zoom” appears on the screen together with the 
level bar and magnifying power (
×1.0, ×1.2, ×1.4, ×1.6, ×2.0, 
×2.5, ×3.2, ×4.0). When “15 sec.” is displayed in the menu, 
“Digital zoom” will appear in approximately 15 seconds.
•To zoom up or zoom down, press the DIGITAL ZOOM T or 
W button on the remote control.
Moving the zoomed image:
While “Digital zoom” appears on the screen, you can move 
the zoomed image with the cursor (5/∞/2/3) button on the 
remote control.
5:Upper part of the image will be
displayed.
∞:Lower part of the image will be
displayed.
2:Left side part of the image will
be displayed.
3:Right side part of the image
will be displayed.
Notes
•This function will not work with some signal sources 
(UXGA, etc). In this case, the DIGITAL ZOOM inhibit 
message appears for a few seconds, as shown on the left. 
To forcibly clear this message, press the EXIT button.
•The quality of the zoomed image reduces in comparison 
with the original one.
•To return to the original size (
×1.0) and original position, 
press the PRESET button while “Digital zoom” is displayed 
on the screen.
DVIVIDEO COMP
QUICK
ALIGN.
PC1 PC2
Y/C HIDE
PRESET
ENTER EXIT
MENU
FREEZESCREEN
OPERATE
DIGITAL
ZOOMZOOM FOCUS
W
W S
T
WT
RM-M160 REMOTE CONTROL UNIT
SCREEN
KEYSTONE
W
S
FREEZE button
PRESET button
EXIT button DIGITAL ZOOM
T/W button
Cursor buttons
5/∞ / 2/3
FREEZE
FREEZE
D.ZOOM
FREEZERemote control unit
Digital zoom 1.2
DIGITAL
ZOOM
WT
Remote control unit 
						

							37
Menu Operations
You can adjust picture quality, set functions, get information on the input video signal, etc. using the menus. From the 
following menu transition diagrams, you can see the overall menus and basic button operation in menu mode. Note that there 
are three menu modes, No signal menu mode, video menu mode and PC menu mode. When the MENU button is pressed, 
the projector enters one of these modes by judging the input signal being received.
■Menu Transition Diagram in No signal Menu Mode
This is displayed if there is no signal from the selected input terminal.
■Quick Reference Guide for No signal Menu Mode
Main Menu in No signal Menu Mode
Set up
Sync level: Low. Std*. High.
Sync timing: 3-5
Options
Flip H: OFF* / ON (Select for upside-down hanging on the ceiling.)
Flip V: OFF* / ON (Select for upside-down hanging on the ceiling.) 
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min]: Selectable sleep times. If no-signal condition continues for the period of selected time 
(Unit: Minutes), the projector enters the stand-by mode. 15 / 30 / 60 / OFF*
Language Language for on-screen display.
Japanese / English* / German / Spanish / Italian / French
Information
Input: Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP, 
PC1, PC2 or DVI)
Switcher: Has no meaning. This display currently has no meaning. (“CH.0” is usually displayed to 
indicate that it is not being used.)
Lamp time: Accumulated used hours of the light-source lamp.
Menu
Set up
Options
Language
InformationEnglish
Deutsch
Español
Italiano
Français
Menu
Set up
Options
Language
InformationInput
Switcher
Lamp time
PC1
CH.0
123 h
Language
Set up
Sync level
Sync timingStd Low High
English
Deutsch
Español
Italiano
Français
Menu
Set up
Options
Language
InformationSync level
Sync timing
Main menu in No signal Menu ModeSubmenus in No signal Menu Mode
Press 5/∞ to select an item.
Press 5/∞ to select an item.
Press 2/3 to set the value.
Press 5/∞ to select an item. 3 or ENTER
EXIT
3 or
ENTER ∞ 5
∞ 5
∞5
EXIT 
						

							38
Menu Operations
■Menu Transition Diagram in Video Menu Mode
Set up 1
Position
Gamma
Aspect ratio
Page 2
ENTER
ENTERCinema
4:3 DownUp
16:9
Lamp control
Normal
LPC
LOC
Keystone 123
12,12
Ye s
Color temp.
All reset?
No
Menu
Image adj.
Set up
Color temp.
Options
Language
Information
Position
Gamma
Aspect ratio
Decoder
Tracking
Deinterlace
Phase
Screen
HDTV
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationMenu display
Line display
Lamp time display
Keystone
Lamp control
Color temp.
Color temp.
RED
GREEN
BLUE
All reset123
123
123
ENTER
Set up 2
Deinterlace
Phase
Screen
HDTV
Page 1
ENTER
124:3
1080i16:9
1035i
Middle HighLow
Film AUTOVideo
Ye s
Image adj.
All reset?
No
ENTER
Position
Disp.Posi. Menu
Decoder
AUTO  [  NTSC  ]
NTSC
NTSC4.43
PA L
SECAM
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationEnglish
Deutsch
Español
Italiano
Français
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationInput
Switcher
Source
Lamp time
PC1CH.0
NTSC
123 h
Language
Page 2
Flip H
Flip V
RS-232C [bps] 
Sleep time [min] 
Page 1OFF
OFF
9600
ENTER
ON
ON
19200
153060OFF
English
Deutsch
Español
Italiano
Français
Set up 2
Tracking
Phase
Screen
HDTV
Page 1123
12
ENTER
4:3
1080i16:9
1035i
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationContrast
Brightness
Color
Tint
Sharpness
All resetImage adj.
Contrast
Brightness
Color
Tint
Sharpness
All reset12
12
12
12
1
ENTER
Set up 1
Position
Gamma
Aspect ratio
Decoder
Page 2
ENTERENTER
ENTERCinema
4:3 DownUp
16:9
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationColor temp.
RED
GREEN
BLUE
Call reset
Options
Menu display
Line display
Lamp time display
Keystone
Lamp control
Page 2ON 15sec
5sec
ENTER
ON
OFF
OFF
ENTERENTER
Set up 1
Position
Gamma
Aspect ratio
Page 2
ENTER
ENTERCinema
4:3 DownUp
16:9
Lamp control
Normal
LPC
LOC
Keystone 123
12,12
Ye s
Color temp.
All reset?
No
Menu
Image adj.
Set up
Color temp.
Options
Language
Information
Position
Gamma
Aspect ratio
Decoder
Tracking
Deinterlace
Phase
Screen
HDTV
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationMenu display
Line display
Lamp time display
Keystone
Lamp control
Color temp.
Color temp.
RED
GREEN
BLUE
All reset123
123
123
ENTER
Set up 2
Deinterlace
Phase
Screen
HDTV
Page 1
ENTER
124:3
1080i16:9
1035i
Middle HighLow
Film AUTOVideo
Ye s
Image adj.
All reset?
No
ENTER
Position
Disp.Posi. Menu
Decoder
AUTO  [  NTSC  ]
NTSC
NTSC4.43
PA L
SECAM
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationEnglish
Deutsch
Español
Italiano
Français
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationInput
Switcher
Source
Lamp time
PC1CH.0
NTSC
123 h
Language
Page 2
Flip H
Flip V
RS-232C [bps] 
Sleep time [min] 
Page 1OFF
OFF
9600
ENTER
ON
ON
19200
153060OFF
English
Deutsch
Español
Italiano
Français
Set up 2
Tracking
Phase
Screen
HDTV
Page 1123
12
ENTER
4:3
1080i16:9
1035i
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationContrast
Brightness
Color
Tint
Sharpness
All resetImage adj.
Contrast
Brightness
Color
Tint
Sharpness
All reset12
12
12
12
1
ENTER
Set up 1
Position
Gamma
Aspect ratio
Decoder
Page 2
ENTERENTER
ENTERCinema
4:3 DownUp
16:9
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationColor temp.
RED
GREEN
BLUE
Call reset
Options
Menu display
Line display
Lamp time display
Keystone
Lamp control
Page 2ON 15sec
5sec
ENTER
ON
OFF
OFF
ENTERENTER
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
3 or
ENTER
You can see the information.
Press 5/∞ to select an item.
Main menu in Video Menu Mode
Press 5/∞ to select an item.Press 2/3 to select Yes or No.
Then, press ENTER to execute.
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.Press ENTER to select an item.
Press5/∞ /2/3 to move the video screen/menu position.
EXIT
Press 5/∞ to select an item.
3 or
ENTER
Press5/∞ to select an item.
Press2/3 to set or adjust the value.
ENTER
EXIT
ENTER
3 or
ENTER
EXIT
∞
∞
∞ 5
5
5
∞
∞ 5
Submenus in Video Menu Mode
ENTER
Press 5/∞ to select an item.
E
N
TE
R
ENTER
ENTER EXIT
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
Press5/∞ to select an item.
Press2/3 to set or adjust the value.
EXIT ENTER
3 or
ENTER
EXIT
3 or
ENTER
EXIT
5
∞
Note
•The display languages of the menus are set to “English” when the projector is 
bought. The display language can be selected from the following 6 languages:
“(Japanese)”, “English (English)”, “Deutsch (German)”, “Español (Spanish)”,
“Italiano (Italian)” and “Français (French)”. (Refer to page 46.)
The language settings in the section are explained in “English”.
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
EXIT
EXITENTER
E
N
T
E
R
*The film function is 
displayed when the 
input signal is 
equivalent to NTSC 
or PAL. The tracking 
function is displayed 
for other signals. ENTER
EXIT
5
ENTER
ENTER
Press5/∞ to select an item.
Press2/3 to set or adjust the value. 
						

							39
Menu Operations 
.
■Quick Reference Guide for Video Menu Mode
*: Factory set value.
Main Menu in Video Menu Mode (While receiving video-device-related signals)
Image adj. 
→ (Refer to page 49)
Contrast: Contrast of the video image being projected can be adjusted. (–30 to +30, 0*)
Brightness: Brightness of the video image being projected can be adjusted. (–30 to +30, 0*) 
Color: Color density of the video image being projected can be adjusted. (–30 to +30, 0*)
Tint: Tint of the video image being projected can be adjusted. (–30 to +30, 0*)
Sharpness: Sharpness of the video image being projected can be adjusted. (–5 to +5, 0*)
All reset: Resets above items to the factory set values.
Yes / No
Set up 1
Position:
Video screen position and menu position can be adjusted. 
→ (Refer to page 51)
Disp. Posi. / Menu
Gamma:Image tone can be changed. Down/Cinema*/Up (Suitable for the cinema programes)
→ (Refer to 
page 52)
Aspect ratio
Selectable aspect ratio, 4:3*/16:9. 
→ (Refer to page 52)
Decoder:Selectable color systems, Normally, set to AUTO. 
 (Refer to page 45)
(This item is displayed only when inputting VIDEO or Y/C.)
AUTO*/NTSC/NTSC4.43/PAL/SECAM
Page 2    Press ENTER to enter the “Set up 2” submenu
Tracking: Normally, no adjustment is required. The lateral size and display area of video image can be 
adjusted. (–128 to + 127) 
→ (Refer to page 47)
Deinterlace:Set when watching movies which were recorded on film.
Phase: Flickering or dim picture image can be adjusted. (0 to 31) 
→ (Refer to page 47)
Screen:
Selectable screen’s aspect ratio. 4:3*/16:9 
→ (Refer to page 46)
HDTV:
Selectable HDTV format. Normally, set to 1080i, 1080i*/1035i 
→ (Refer to page 46)
Page 1: Press ENTER to return to “Page 1” submenu.
Color temp.
Color temp.: Adjustable color temperature, Low/Middle*/High.
Will be adjusted to correct reddish or blueish image.
RED:
Adjusts the red level. (0 to 255, the adjustable range varies depending on signals)
GREEN:
Adjusts the green level. (0 to 255, the adjustable range varies depending on signals)
BLUE:
Adjusts the blue level. (0 to 255, the adjustable range varies depending on signals)
All-reset:
Reset above items to the factory set values.
Yes/No
Options
→ (Refer to page 54)
Options 1
Menu display:15sec* (Menu disappears in 15 seconds.) / ON (Menu stays on.) 
Line display: 5sec* (Line display such as “VIDEO”, “Y/C”, “PC1”, or “PC2” appears on top right of the screen for 
5 seconds when the VIDEO or PC button is pressed.) / OFF (Line display does not appear.)
Lamp time display:
ON*: Displays when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
OFF: Does not display when the lamp use time reaches 1000 hours when set in the LPC or LOC mode.
Keystone: Press ENTER to enter the Keystone submenu.
Keystone: Adjust to correct the trapezoidal distortion of the projected image.
(–80 to +120, 0*)
Lamp control:
Normal*:Used as a normal lamp.
LPC: Lamp brightness is automatically controlled with time.
LOC:
Lamp brightness is controlled in 7 levels (-6 to 0) irrespective of the time. This is set within the menu.
Page 2: Press ENTER to enter the “Page 2” submenu.
Flip H.: OFF* / ON (Select for upside-down hanging on the ceiling.)
Flip V: OFF* / ON (Select for upside-down hanging on the ceiling.) 
RS-232C [bps]: Selectable baud rate (transmission speed). 9600 / 19200*
Sleep time [min]: Selectable sleep times. If no-signal condition continues for the period of 
selected time (Unite: Minutes), the projector enters the stand-by mode. 15 / 30 
/ 60 / OFF*
Page 1: Press ENTER to return to the “Page 1” submenu.
Language
Language for on-screen display. 
→ (Refer to page 46)
Japanese / English* / German / Spanish / Italian / French
Information 
→ (Refer to page 56)
Input:
Shows the terminal name selected by the VIDEO or PC button. (Y/C, VIDEO, COMP, PC1, PC2 or DVI)
Switcher: Has no meaning. This display currently has no meaning, (“CH.0” is usually displayed to indicate 
that it is not being used.)
Source: Shows the projected image’s type of video signal.
Lamp time: Accumulated used hours of the light-source lamp. 
						

							40
Menu Operations
■Menu Transition Diagram in PC Menu Mode
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationTracking
Phase
Position
Resize
Clamp
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationMenu display
Line display
Lamp time display
Keystone
Lamp control
Ye s
Image adj.
All reset?
No
ENTER
Position
Disp.Posi. Menu
Ye s
Color temp.
All reset?
No
Color temp.
Color temp.
RED
GREEN
BLUE
All reset Color temp.
RED
GREEN
BLUE
All reset123
123
123
ENTER
Middle HighLow
Menu
Image adj.
Set up
Color temp.
Options
Language
Information
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationEnglish
Deutsch
Español
Italiano
Français
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationInput
Switcher
Resolution
Frequency H 
Frequency V
Lamp time
PC 1CH.0
NTSC
79.9
75
123kHz
Hz
h
Language
English
Deutsch
Español
Italiano
Français
Image adj.
Contrast
Brightness
Sharpness
All reset12
12
ENTER12345
Menu
Image adj.
Set up
Color temp.
Options
Language
InformationContrast
Brightness
Sharpness
All reset
Set up 1
Position
Resize
Options
Menu display
Line display
Lamp time display
Keystone
Lamp control
Page 2ON 15sec
5sec
ENTER
ON
OFF
OFF
ENTERENTER
Page 2
Flip H
Flip V
RS-232C [bps] 
Sleep time [min] 
Page 1OFF
OFF
9600
ENTER
ON
ON
19200
153060OFF
Keystone   0
12,12
Set up 1
Tracking
Phase
Position
Resize
Clamp123
12
ENTER
STBP1:1PanelAspect
ENTER1:1PanelAspect
Lamp control
Normal
LPC
LOC
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
3 or
ENTER Press 5/∞ to select an item.Press 2/3 to select Yes or No.
Then, press ENTER to execute.
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
Press ENTER to select an item.Press 5/∞ / 2/3 to move the
video screen/menu position. EXIT
3 or
ENTER
EXIT
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
ENTER
EXIT
EXIT
ENTER
3 or
ENTER
EXIT
3 or
ENTER
EXIT
∞
∞
∞ 5
5
5
∞5
ENTEREXIT
ENTERENTEREXIT ENTER
∞
5
Main menu in PC Menu ModeSubmenus in PC Menu Mode
Press 2/3 to select Yes or No.
Then, press ENTER to execute.
Press 5/∞ to
select an item.
Press 5/∞ to select an item.
Press 2/3 to set or adjust the value.
Note
•The display languages of the menus are set to “English” when the projector is 
bought. The display language can be selected from the following 6 languages: 
“(Japanese)”, “English (English)”, “Deutsch (German)”, “Español
(Spanish)”, “Italiano (Italian)” and “Français (French)”. (Refer to page 46.)
The language settings in the section are explained in “English”.You can see the information.∞
5