Faroudja D-Ila1080mf1 Installation And Operational Manual

21
Connecting the Power Cable 
(Supplied) 
Before	plugging	in	the	power	cable/cord,	en-
sure	that	all	devices	have	been	connected.	
1
2
PowerCable
(Supplied)
1 Connect the supplied power cable to 
the power input terminal of this unit 
2 Connect the earth wire to the earth 
terminal available in the building, 
followed by inserting the mains plug 
of the supplied power cable into the 
wall outlet 
Precautions Against Fire and Electric 
Shock 
•	 Since	the	power	consumption	of	this	unit	is	
high,	insert...

22
Basic Operation
After	installation,	the	projector	will	require	
initial	set-up,	adjustment,	alignment	and	con-
figuration	(see	next	page).	Once	this	has	been	
done,	the	unit	can	be	used	simply	by	following	
these	basic	operational	procedures.
T
W
ZOOM
+
-
FOCUS
MENUEXITOPERATEON
OPERATEOFF
HIDE
RS232CRxTx
1
2
3
6
5
4
Indicators
1 Remove the lens cap 
We	recommend	keeping	the	lens	cap	in	place	
when	the	unit	is	not	in	use.
2 Apply Mains Power
On	the	application	of	power,	the	STANDBY	
indicator	on	the...

2
Adjustments and Settings Using Menus
The	menus	displayed	on	the	screen	are	used	to	perform	adjustment	and	setting	for	this	unit.	
Menu Structure
The	menus	of	this	unit	have	the	following	structure.	Characters	on	the	screen	are	displayed	in	Eng-
lish	only.	
NOTE:	Press	the	ENTER	button	to	switch	to	the	test	pattern	image.	There	are	10	types	of	test	pat-
terns.	Press	the	ENTER	or	TEST	button	to	alter	the	test	pattern	to	be	projected.	Press	the	EXIT	but-
ton	to	clear	the	menu	screen.	Press	the	EXIT...

2
Menu Operation Buttons 
T
W
ZOOM
+
-
FOCUS
MENUEXITOPERATEON
OPERATEOFF
HIDE
RS232CRxTx
MenuOperationButtons
Menus	can	be	accessed	via	the	projector	
control	panel	(above)	or	via	the	correspond-
ing	buttons	on	the	remote	–	see	table	below.	
Examples	refer	to	the	menu	screens	on	the	
previous	page.
Button
FunctionRemoteControlUnitProjector
Displays the main menu.
•Presstoclearthemenuscreenwhenthemenuisdisplayed.
Confirms theselected item on the mainmenu....

2
Menu Configuration
1 Image Adjust Menu 
Permits	image	adjustment
Gamma 
Switches	the	gradation	characteristics	of	the	
image.	Select	your	preference	setting	values	
according	to	the	image	to	be	viewed.	
Setting Values: Normal, A, B, Custom 
Default Value: Normal 
•	 Setting	to	‘Custom’	enables	you	to	set	a	specific	
gamma	value	via	a	computer	connected	to	the	
projector	using	Gamma	adjustment	software.	
(Default	picture	quality	is	equivalent	 to	‘Normal’)	
•	 You	can	download	the	Gamma	adjustment...

2
3 Options Menu 
Menu Display 
Adjusts	the	display	duration	of	the	menu	
screen.	
Setting Values: 1sec, On 
Default Value: 1sec
•	 The	menu	screen	display	will	not	disappear	au-
tomatically	when	this	is	set	to	On.	Instead,	press	
the	EXIT	button	to	clear	the	menu	screen.	
Sleep Time 
Sets	the	length	of	time	after	cessation	of	video	
input	before	automatically	switching	the	unit	
to	the	standby	mode
Setting Values (min): 1, 0, 0, Off
Default Value: Off 
RC232C (bps) 
Sets...

2
The	life	of	light-source	lamps	used	for	this	unit	
is	about	2000	hours.	
•	 The	lamp	life	of	2000	hours	is	merely	the	aver-
age	life	span	of	light-source	lamps	and	we	do	
not	provide	any	guarantee	for	this	figure.	The	
lamp	life	may	not	reach	2000	hours	depend-
ing	on	the	operating	conditions.	Deterioration	
progresses	rapidly	when	the	remaining	lamp	
usage	time	is	short.	Get	ready	or	replace	with	
a	new	lamp	unit	when	the	accumulated	usage	
time	exceeds	1900	hours.	Depending	on	the	
operating...

2
Lamp Replacement Procedure 
1 Remove the control panel cover 
•	 See	page	10	for	details	on	removing	the	control	
panel	cover.
2 Loosen the screw and remove the 
lamp cover 
•	 Undo	the	retaining	screw	with	a	‘+’	screwdriver.	
3 Loosen the screws on the lamp unit 
and lift up the handle 
•	 Loosen	the	2	screws	with	a	‘+’	screwdriver.	
4 Pull out the lamp unit 
Control Panel Cover
LampCover
Handle
LampUnit 

2
5 Slide in the new lamp unit until it is 
fully inserted 
Handling the new Lamp Unit 
Do	not	touch	the	glass	surface	of	the	lamp	
directly	with	your	hand	or	stain	it.	Touching	it	
with	a	bare	hand	may	dirty	the	surface,	hence	
shortening	the	lamp	life,	causing	marked	
performance	deterioration,	image	darkening,	
lamp	blowout	and	other	problems.	
6 Tighten the screws of the lamp unit 
and fold down the handle 
•	Fasten	the	2	screws	with	a	‘+’	screwdriver.	
7 Re-attach the lamp cover and fasten...

0
Resetting Lamp Time
After	installing	a	new	lamp	unit,	the	lamp	
time	must	be	reset	before	the	projector	can	be	
used.	Resetting	the	lamp	time	resets	the	inter-
nal	counter	to	zero	hours.	
NOTE:		if	the	previous	lamp	had	accumulated	
over	2,000	hours	of	use,	the	projector	will	not	
operate	until	the	lamp	time	has	been	reset.
1 Reconnect power to the projector
•	 The	main	power	turns	on	and	the	Standby	indi-
cator	on	the	unit	lights	up.	
2 Point the remote control unit at one 
of the sensors on the...