Faroudja D-Ila1080mf1 Installation And Operational Manual

							
INSTALLERS:	 Please	review	this	manual	carefully	before	contacting	Technical	Support.
PRODUCT OWNERS:	 Please	contact	your	authorised	Meridian/Faroudja	dealer	for	product	or	
installation	questions.
D-ILA 1080MF1
HD	D-ILA	Digital	Video	Projector
PRELIMINARY
Installation and Operation Manual 
						

							
For Customer use : 
Enter	the	serial	number	of	your	unit	–	located	on	the	side	panel	of	the	cabinet	–	below.	
Retain	this	information	for	future	reference.	 
						

							

Safety precautions
IMPORTANT INFORMATION
NOTICE 
This	product	has	a	High	Intensity	Discharge	
(HID)	lamp	that	contains	a	small	amount	of	
mercury.	It	also	contains	lead	in	some	com-
ponents.	Disposal	of	these	materials	may	be	
regulated	in	your	community	due	to	environ-
mental	considerations.	For	disposal	or	recycling	
information	please	contact	your	local	authori-
ties.		
WARNING: TO PREVENT FIRE OR SHOCK 
HAZARDS, DO NOT EXPOSE THIS 
APPLIANCE TO RAIN OR MOISTURE.  
WARNING: THIS APPARATUS MUST BE 
EARTHED.  
CAUTION:	To	reduce	the	risk	of	electric	shock,	
do	not	remove	cover.	Refer	servicing	to	quali-
fied	service	personnel.		
This	projector	is	equipped	with	a	3-pin	earthed	
(grounded)	plug.	If	you	are	unable	to	insert	the	
plug	into	the	outlet,	contact	your	electrician.		
FCC INFORMATION (U.S.A. only) 
CAUTION:	Changes	or	modification	not	ap-
proved	by	Meridian	could	void	the	user’s	
authority	to	operate	the	equipment.	
NOTE:	This	equipment	has	been	tested	and	
found	to	comply	with	the	limits	for	Class	B	
digital	devices,	pursuant	to	Part	15	of	the	FCC	
Rules.	These	limits	are	designed	to	provide	
reasonable	protection	against	harmful	interfer-
ence	in	a	residential	installation.	This	equip-
ment	generates,	uses,	and	can	radiate	radio	
frequency	energy	and,	if	not	installed	and	used	
in	accordance	with	the	instructions,	may	cause	
harmful	interference	to	radio	communications.	
However,	there	is	no	guarantee	that	interfer-
ence	will	not	occur	in	a	particular	installation.	
If	this	equipment	does	cause	harmful	interfer-
ence	to	radio	or	television	reception,	which	
can	be	determined	by	turning	the	equipment	
off	and	on,	the	user	is	encourage	to	try	to	
correct	the	interference	by	one	or	more	of	the	
following	measures:	
•	Reorient	or	relocate	the	receiving	antenna.	
•	Increase	the	separation	between	the	equip-
ment	and	receiver.	
•	Connect	the	equipment	into	an	outlet	on	a	
circuit	different	from	that	to	which	the	receiver	
is	connected.	
•	Consult	the	dealer	or	an	experienced	radio/
TV	technician	for	help.		
MACHINE NOISE INFORMATION 
(Germany only) 
Machine	Noise	Information	Ordinance	3.	
GSGV,	January	18,	1991:	The	sound	pressure	
level	at	the	operator	position	is	equal	or	less	
than	70	dB	(A)	according	to	ISO	7779.		
Avoid burning-in of the D-ILA device 
Do	not	allow	the	same	still	picture	to	be	pro-
jected	for	a	long	time	or	an	abnormally	bright	
video	picture	to	be	projected.	Do	not	project	
video	images	with	high-intensity	or	high	con-
trast	on	a	screen.	The	video	image	could	be	
burnt	into	the	D-ILA	device.	
Use	special	care	when	projecting	video	games	
or	computer	program	images.	There	is	no	
problem	with	ordinary	videocassette	playback	
images.	
Installation location considerations
Do	not	install	the	projector	in	a	location	that	
cannot	support	its	weight	securely.
If	the	installation	mounting	is	not	sturdy	
enough,	the	projector	could	fall	or	overturn,	
possibly	causing	personal	injury.
IMPORTANT SAFEGUARDS 
This	unit	has	been	engineered	and	manufac-
tured	to	ensure	your	personal	safety	under	
normal	operating	conditions.	However,	IM-
PROPER	USE	CAN	RESULT	IN	POTENTIAL	ELEC-
TRICAL	SHOCK	OR	FIRE	HAZARD.	In	order	not	
to	defeat	the	safeguards	incorporated	into	
this	product,	observe	the	following	basic	rules	
for	its	installation,	use	and	service.	Please	read	
these	Important	Safeguards	carefully	before	
use.	 
						

							

•	 All	the	safety	and	operating	instructions	should	
be	read	before	the	product	is	operated.	
•	 The	safety	and	operating	instructions	should	be	
retained	for	future	reference.	
•	 All	warnings	on	the	product	and	in	the	operat-
ing	instructions	should	be	adhered	to.	
•	 All	operating	instructions	should	be	followed.	
•	 Place	the	projector	near	a	wall	outlet	where	the	
plug	can	be	easily	unplugged.	
•	 Unplug	this	product	from	the	wall	outlet	before	
cleaning.	Do	not	use	liquid	cleaners	or	aerosol	
cleaners.	Use	a	damp	cloth	for	cleaning.	
•	 Do	not	use	attachments	not	recommended	by	
the	product	manufacturer,	as	they	may	be	haz-
ardous.	
•	 Do	not	use	this	product	near	water.	Do	not	use	
immediately	after	moving	from	a	low	tempera-
ture	to	high	temperature,	as	this	causes	conden-
sation,	which	may	result	in	fire,	electric	shock,	
or	other	hazards.	
•	 Do	not	place	this	product	on	an	unstable	cart,	
stand,	or	table.	The	product	may	fall,	causing	
serious	injury	to	a	child	or	adult,	and	serious	
damage	to	the	product.	The	product	should	
be	mounted	according	to	the	manufacturer’s	
instructions,	and	should	use	a	mount	recom-
mended	by	the	manufacturer.	
•	When	the	product	is	used	on	a	
cart,	care	should	be	taken	to	avoid	
quick	stops,	excessive	force,	and	
uneven	surfaces	which	may	cause	
the	product	and	cart	to	overturn,	
damaging	equipment	or	causing	
possible	injury	to	the	operator.	
•	 Slots	and	openings	in	the	cabinet	are	provided	
for	ventilation.	These	ensure	reliable	operation	
of	the	product	and	protect	it	from	overheat-
ing,	and	must	not	be	blocked	or	covered.	(The	
openings	should	never	be	blocked	by	placing	
the	product	on	a	bed,	sofa,	rug,	or	similar	sur-
face.	The	unit	should	not	be	placed	in	a	built-in	
installation	such	as	a	bookcase	or	rack	unless	
proper	ventilation	is	provided	and	the	manufac-
turer’s	instructions	have	been	adhered	to.)	For	
proper	ventilation,	separate	the	product	from	
other	equipment	which	may	prevent	ventilation	
by	a	distance	of	at	least	1ft	(30	cm).	
•	 This	product	should	be	operated	only	with	the	
type	of	power	source	indicated	on	the	label.	If	
you	are	not	sure	of	the	type	of	power	supply	to	
your	home,	consult	your	product	dealer	or	local	
power	company.	
•	 This	product	is	equipped	with	a	three-pin	plug.	
This	plug	will	fit	only	into	an	earthed	(grounded)	
power	outlet.	If	you	are	unable	to	insert	the	
plug	into	the	outlet,	contact	your	electrician	
to	install	the	proper	outlet.	Do	not	defeat	the	
safety	purpose	of	the	grounded	plug.	
•	 Power-supply	cords	should	be	routed	so	that	
they	are	not	likely	to	be	walked	on	or	pinched	
by	items	placed	upon	or	against	them.	Pay	
particular	attention	to	cords	at	doors,	plugs,	
receptacles,	and	the	point	where	they	exit	from	
the	product.	
•	 For	added	protection	of	this	product	during	a	
lightning	storm,	or	when	it	is	left	unattended	
and	unused	for	long	periods	of	time,	unplug	it	
from	the	wall	outlet	and	disconnect	the	cable	
system.	This	will	prevent	damage	to	the	product	
due	to	lightning	and/or	power	line	surges.	
•	 Do	not	overload	 wall	outlets,	 extension	 cords,	or	
power	outlet	receptacles	on	other	equipment	as	
this	can	result	in	a	risk	of	fire	or	electric	shock.	
•	 Never	push	objects	of	any	kind	into	this	product	
through	openings	as	they	may	touch	danger-
ous	voltage	points	or	short	out	parts	that	could	
result	in	a	fire	or	electric	shock.	Never	spill	liquid	
of	any	kind	on	the	product.	
•	 Do	not	attempt	to	service	this	product	yourself	
as	opening	or	removing	covers	may	expose	you	
to	dangerous	voltages	and	other	hazards.	Refer	
all	service	to	qualified	service	personnel.	
•	 Unplug	this	product	from	the	wall	outlet	and	
refer	service	to	qualified	service	personnel	under	
the	following	conditions:	a)	When	the	power	
supply	cord	or	plug	is	damaged.	b)	If	liquid	
has	been	spilled,	or	objects	have	fallen	on	the	
product.	c)	If	the	product	has	been	exposed	to	
rain	or	water.	d)	If	the	product	does	not	operate	
normally	by	following	the	operating	instruc-
tions.	Adjust	only	those	controls	that	are	cov-
ered	by	this	Operation	Manual,	as	an	improper	
adjustment	of	controls	may	result	in	damage	
and	will	often	require	extensive	work	by	a	quali-
fied	technician	to	restore	the	product	to	normal	
operation.	e)	If	the	product	has	been	dropped	
or	damaged	in	any	way.	f)	When	the	product	
exhibits	a	distinct	change	in	performance	-	this	
indicates	a	need	for	service.	
•	 When	replacement	parts	are	required,	be	sure	
the	service	technician	has	used	replacement	
parts	specified	by	the	manufacturer	or	with	the	
same	characteristics	as	the	original	part.	Unau-
thorized	substitutions	may	result	in	fire,	electric	
shock,	or	other	hazards.	
•	 Upon	 completion	 of	any	 service	 or	repairs	 to	this	
product,	ask	the	service	technician	to	perform	
safety	checks	to	determine	that	the	product	is	in	
proper	operating	condition.	
•	 The	product	should	be	placed	more	than	one	
foot	away	from	heat	sources	such	as	radia-
tors,	heat	registers,	stoves,	and	other	products	
(including	amplifiers)	that	produce	heat.	
•	 When	connecting	other	products	such	as	VCR’s,	
and	personal	computers,	you	should	turn	off	
the	power	of	this	product	for	protection	against	
electric	shock.	
•	 Do	not	place	combustibles	behind	the	cooling	
fan.	For	example,	cloth,	paper,	matches,	aerosol	
cans	or	gas	lighters	that	present	special	hazards	
when	over	heated.	
•	 Do	not	look	into	the	projection	lens	while	the	
illumination	lamp	is	turned	on.	Exposure	of	your	
eyes	to	the	strong	light	can	result	in	impaired	
eyesight.	
•	 Do	not	look	into	the	inside	of	this	unit	through	 
						

							

vents	(ventilation	holes),	etc.	Do	not	look	at	the	
illumination	lamp	directly	by	opening	the	cabi-
net	while	the	illumination	lamp	is	turned	on.	
The	illumination	lamp	also	emits	ultraviolet	rays	
and	the	light	is	so	powerful	that	your	eyesight	
can	be	impaired.	
•	 Do	not	drop,	hit,	or	damage	the	light-source	
(lamp	unit)	in	any	way.	It	may	cause	the	lamp	
to	break	and	lead	to	injuries.	Do	not	use	a	
damaged	lamp.	If	the	lamp	is	broken,	ask	your	
dealer	to	repair	it.	Fragments	from	a	broken	
lamp	may	cause	injuries.	
•	 The	lamp	used	in	this	projector	is	a	high	pres-
sure	mercury	lamp.	Be	careful	when	disposing	
of	the	lamp.	In	case	of	doubt	on	how	to	do	this,	
please	consult	your	dealer.	
•	 Do	not	ceiling-mount	the	projector	to	a	place	
which	tends	to	vibrate;	otherwise,	the	mounting	
fixture	of	the	projector	could	be	broken	by	the	
vibration,	possibly	causing	it	to	fall	or	overturn,	
which	could	lead	to	personal	injury.	
Use	only	the	accessory	cord	designed	for	this	
product	to	prevent	shock.	The	power	sup-
ply	voltage	rating	of	this	product	is	AC120	
V,	AC100	V	–	AC240	V,	and	the	power	cord	
attached	conforms	to	the	appropriate	power	
supply	voltage.	Use	only	the	power	cord	des-
ignated	by	your	dealer	to	ensure	Safety	and	
EMC.	When	used	on	an	alternative	power	
supply	voltage,	the	power	cable	may	need	to	
be	changed.	Ensure	that	the	power	cable	used	
for	the	projector	is	the	correct	type	for	the	AC	
outlet	in	your	country.	If	necessary,	consult	
your	product	dealer.	
For United KingdomFor European countries 
Powercable
Power supply voltage:AC 120 V
DO	NOT	allow	any	unqualified	person	to	install	
the	unit.	Be	sure	to	ask	your	dealer	to	install	
the	unit	(e.g.	attaching	it	to	the	ceiling)	since	
special	technical	knowledge	and	skills	are	re-
quired	for	installation.	If	an	unqualified	person	
performs	installation,	it	may	result	in	personal	
injury	or	electric	shock.	
WARNING: 
Do	not	cut	off	the	main	plug	from	this	equip-
ment.	If	the	plug	fitted	is	not	suitable	for	the	
power	points	in	your	home	or	the	cable	is	too	
short	to	reach	a	power	point,	then	obtain	an	
appropriate	safety	approved	extension	lead	or	
adapter	or	consult	your	dealer.	If	nonetheless	
the	mains	plug	is	cut	off,	remove	the	fuse	and	
dispose	of	the	plug	immediately,	to	avoid	a	
possible	shock	hazard	by	inadvertent	connec-
tion	to	the	main	supply.	If	a	new	mains	plug	
has	to	be	fitted,	then	follow	the	instructions	
given	below:	
WARNING: THIS	APPARATUS	MUST	BE	
EARTHED.	
IMPORTANT:	The	wires	in	the	mains	lead	on	
this	product	are	coloured	in	accordance	with	
the	following	code:	
Green/yellow:	 Earth.	
Blue	:	 Neutral.	
Brown	:	 Live.
As	these	colours	may	not	correspond	with	
coloured	markings	identifying	the	terminals	in	
your	plug,	proceed	as	follows:	
•	 The	wire	which	is	coloured	green-and-yellow	
must	be	connected	to	the	terminal	which	is	
marked	with	the	Earth/Ground	symbol,	the	
letter	E	or	the	safety	earth	or	coloured	green	or	
green-and-yellow.	
•	 The	wire	which	is	coloured	blue	must	be	con-
nected	to	the	terminal	which	is	marked	with	the	
letter	N	or	coloured	black.	
•	 The	wire	which	is	coloured	brown	must	be	con-
nected	to	the	terminal	which	is	marked	with	the	
letter	L	or	coloured	red.	
When	replacing	the	fuse,	be	sure	to	use	only	
a	correctly	rated,	approved	type,	and	re-fit	the	
fuse	cover.	
IF	IN	DOUBT,	CONSULT	A	COMPETENT	
ELECTRICIAN.	 
						

							

Information for Users on Disposal of 
Old Equipment (EU Only)
Attention:
Thissymbolisonly
validintheEuropean
Union.
[European Union] 
This	symbol	indicates	that	the	electrical	and	
electronic	equipment	should	not	be	disposed	
as	general	household	waste	at	its	end-of-life.	
Instead,	the	product	should	be	handed	over	to	
the	applicable	collection	point	for	the	recy-
cling	of	electrical	and	electronic	equipment	
for	proper	treatment,	recovery	and	recycling	
in	accordance	with	your	national	legislation.	
By	disposing	of	this	product	correctly,	you	will	
help	to	conserve	natural	resources	and	will	
help	prevent	potential	negative	effects	on	the	
environment	and	human	health	which	could	
otherwise	be	caused	by	inappropriate	waste	
handling	of	this	product.	For	more	information	
about	collection	point	and	recycling	of	this	
product,	please	contact	your	local	authority,	
your	household	waste	disposal	service	or	the	
shop	where	you	purchased	the	product.	Penal-
ties	may	be	applicable	for	incorrect	disposal	of	
this	waste,	in	accordance	with	national	legisla-
tion.	
(Business	users)	
If	you	wish	to	dispose	of	this	product,	contact	
your	Meridian	dealer	or	distributor	or	Merid-
ian	Audio	Ltd	to	obtain	information	about	the	
take-back	of	the	product.	
[Other Countries outside the European 
Union] 
If	you	wish	to	dispose	of	this	product,	please	
do	so	in	accordance	with	applicable	national	
legislation	or	other	rules	in	your	country	for	
the	treatment	of	old	electrical	and	electronic	
equipment.	
Caution
Avoid Burning-in of the D-ILA Device 
Do	not	allow	the	same	still	picture	to	be	pro-
jected	for	a	long	time	or	an	abnormally	bright	
video	image	to	be	projected.
Do	not	project	still	images,	etc.	with	a	high	
intensity	or	high	contrast	on	the	screen	for	a	
long	time.	This	video	image	could	be	burnt	
into	this	D-ILA	device.
Pay	special	attention	when	projecting	video	
games	and	computer	program	images.
There	is	no	problem	with	ordinary	videocas-
sette	playback	images.
Viewing Conditions 
Avoid	direct	exposure	of	the	screen	to	direct	
sunlight	and	illumination.	Image	quality	will	be	
maximised	by	reducing	room	illumination.	
Do	not	view	screen	for	prolonged	hours.	Look-
ing	at	the	screen	continually	for	a	prolonged	
time	will	cause	your	eyes	to	get	tired.	Allow	
your	eyes	to	rest	at	intervals.	
Do	not	use	this	unit	if	the	image	flickers,	as	
this	may	cause	your	eyesight	to	deteriorate.	
Operating Environment
Do	not	use	this	unit	in	rooms	with	cigarette	
smoke	or	oily	smoke.	Ingress	of	smoke	may	
cause	the	unit	to	malfunction.	
When	mounting	this	unit	to	the	ceiling,	check	
temperature	around	the	unit.
When	a	heater	is	in	use,	the	ceiling	may	reach	
a	temperature	higher	than	anticipated,	leading	
to	malfunction	of	the	unit.
Maintenance Procedures 
Remove	dirt	from	the	projector	enclosure	with	
a	soft	cloth.	In	case	of	heavy	soiling,	soak	a	
cloth	in	a	neutral	detergent	diluted	with	water,	
wring	dry	and	wipe,	followed	by	wiping	again	
using	a	dry	cloth.	 
						

							

To	avoid	damage	to	the	cabinet,	please	ob-
serve	the	following	precautions:	
•	 Do	not	clean	with	an	abrasive	cloth	or	cleaner
•	 Do	not	use	excessive	force	when	cleaning
•	 Do	not	attempt	to	clean	the	unit	with	paint	
thinner,	benzene	or	other	solvents	that	may	at-
tack	the	enclosure.
•	 Do	not	spray	volatile	chemicals	such	as	insecti-
cide	on	the	unit
•	 Do	not	allow	prolonged	contact	with	rubber	or	
plastic	products	
Dirt	on	the	lens	should	be	removed	using	
commercial	blowers,	lens	cleaning	papers	or	
microfibre	cloths	(designed	for	cleaning	glasses	
and	cameras).	Do	not	use	fluid-type	clean-
ing	agents,	as	this	may	lead	to	peeling	of	the	
surface	coating	film.	The	lens	surface	is	fragile:	
avoid	rubbing	it	hard	or	knocking	it. 
						

							

Contents
SAFETY	PRECAUTIONS		3
Caution  6
Accessories  8
Optional	Accessories	8
Controls and Features  9
Front,	top	&	underside	9
Rear	&	right	side		10
Control	panel		11
Indicators			12
Indicator	display		 13
Remote	control		14
Loading	batteries	into	the	remote	 15
Installing the Projector  16
Considerations	for	installation	16
Mounting	the	projector		16
Minimum	space	requirements	16
Projector	and	screen	Installation	17
Screen	size	and	projection	distance		 18
Lens	Shift	setting	19
Interfacing the projector 20
Connecting	to	devices	20
Connecting	the	power	21
Basic Operation  22
Adjustments and Settings Using Menus  23
Menu	structure		23
Menu	operation	buttons	24
Accessing	the	menus	30
Menu	configuration	25
Replacing the Lamp 27
The	lamp	and	lamp	usage	time	27
Lamp	replacement	procedure	28
Resetting	lamp	time	30
Cleaning and replacing the filter 30 
On-screen Warnings 31
Warning Indicator combinations 32
Troubleshooting 33
Interface Sockets 34
RS-232C External Control 35
Specifications 37
Accessories
The	following	accessories	are	packed	together	
with	this	unit.	Please	confirm	all	items.	If	any	
item	is	missing,	please	contact	your	dealer.	
Instructions	 x1
Power	Cord	x1
Remote	Control	x1
AAA	size	Batteries	for	remote	control	 x3
Optional Accessories
Please	contact	your	authorised	dealer	for	de-
tails:	
Replacement	Lamp	:	BHL5008-S	(Lamp	Unit)	
Replacement	Filter	:	LC32058-002A	(Inner	
Filter)	 
						

							

A Indicator 
Please	refer	to	‘Indicators’	(Page	12)	for	details.	
B Air Inlets 
(2	in	front	and	1	at	bottom	surface)	
The	air	inlets	absorb	air	to	cool	the	interior	of	
the	unit.	Do	not	block	or	allow	warm	air	to	
blow	into	them.	This	may	cause	the	unit	to	
malfunction.	
C Power Zoom Lens 
1.9x	‘normal’	power	zoom	lens		
(model	DILA1080MF1)
1.4x	‘short-throw’	power	zoom	lens		
(model	DILA1080MF1S)
• Before projection, remove the lens cap. 
D Remote Sensor (Front) 
When	operating	with	the	remote	control,	aim	
it	towards	the	sensor.	(Also	see	page	14)	
• A remote sensor is also located on the rear of 
the unit. 
E Lens Cap 
• Fit the cap on the lens when this unit is not in 
use.
F Lens Shift Cover 
Remove	this	cover	when	using	the	Lens	Shift	
feature	for	shifting	the	projecting	position	in	
the	vertical	direction.	
	
G Foot 
It	is	set	at	the	lowest	position	when	shipped	
from	the	factory.	This	unit	does	not	come	with	
a	function	to	adjust	the	gradient.	
H Filter 
Cleans	air	drawn	in	from	the	air	inlet.	Please	
clean	this	filter	regularly.	(Page	30)	
Controls & Features
Front, top and underside
A
B
F
B
CD
E
G
H
G
Underside 
						

							
10
A Control Panel Cover 
Remove	this	cover	when	operating	this	unit	or	
when	replacing	the	lamp	unit.	
• Unlock the cover, followed by sliding it down-
wards to remove it. 
• Please refer to page 11 for details on the con-
trol panel. 
Handling the Control Panel Cover 
• The gap between the body of the unit and the 
control panel cover is narrow. Be careful not to 
stick your finger into the gap between the body 
of the unit and the control panel cover. 
• After attaching the control panel cover, check 
that the lock is fastened securely. 
B Exhaust Vent 
Warm	air	is	expelled	through	this	vent	to	keep	
the	system	cool.	Do	not	block	the	exhaust	
vents	as	this	may	cause	the	unit	to	overheat	
and	fail.	
C AC Power Input Socket 
This	is	the	AC	power	input	socket.	Connect	
the	supplied	power	cable	to	this	socket.	
D Remote Sensor (Rear) 
When	operating	with	the	remote	control,	aim	
it	towards	the	sensor.	(Page	14)	
• A remote sensor is also located at the front of 
the unit.
E Screen Trigger socket 
This	socket	is	used	for	controlling	a	motorised	
screen.	An	output	at	DC	+12	V/100	mA	(max.)	
is	produced	when	the	power	is	on.	
• Consult a qualified technician for a connection 
with the screen. 
F Service Connector 
This	connector	is	intended	for	servicing	pur-
poses	and	should	not	normally	be	used.	
G RS-232C Serial Port (D-sub 9 Pin) 
The	projector	can	be	controlled	by	serial	com-
mands	from	a	computer	or	home	automation	
control	system	connected	to	this	port.	
• For details, please check with your authorized 
dealer. 
H DVI input (DVI-D 24 Pin) 
This	is	the	input	socket	for	video	signals.	
1080/50p	and	1080/60p	signals	are	supported	
and	HDCP	content	protection	capability	is	
provided.	
Rear & Right Side
DVIRS-232CSCREENTRIGGERSERVICE
A
C
B
E    FGHD
Removingthecontrol
panelcover
Lock
Release