Epson Stylus Pro GS6000 User Manual

21
Setting Up the Printer|21
Installing the Printer on the Stand
1. Have six people lift the printer onto the stand. If you like, you can lift 
the printer using two 1-inch × 84-inch steel pipes (available at hardware 
stores). Insert the pipes into the guides beneath the printer.
WARNING: Six or more 
people are required to lift 
the printer.  Caution: Do not remove 
the packing tape from the 
printer at this point. The 
tape holds the printer 
parts in place as you 
complete installation.
Do not lift...

22
22|Setting Up the Printer
Be careful not to damage the waste ink connector and tube hanging 
beneath the printer as you place it on the stand.
2. Attach the printer to the stand using the four wing screws.
 

23
Setting Up the Printer|23
3. Place the waste ink tank into the bracket on the stand and close the 
spigot valve all the way, as shown.
4. Remove the plastic from the ends of the waste ink tube and sensor cable. 
Then connect the sensor cables and securely attach the waste ink tube to 
the tank.
Be careful not to crimp the waste ink tube as you attach it.
Caution: Make sure you 
close the spigot valve all 
the way to prevent spills.
Waste ink tank
Caution: Make sure you 
remove the plastic from 
the...

24
24|Setting Up the Printer
Installing the Auto Take-Up Reel
1. Make sure you have all the items shown below in the Auto Take-Up 
Reel box:
2. Loosen the four screws securing the mounting plate to the right 
controller bracket, then remove the bracket.
Scroller bar with empty media core
Left mounting 
bracket Right controller 
bracket Cushioning roller
Hex wrench
Ten hex bolts
Loosen screws only
 

25
Setting Up the Printer|25
3. Install the mounting bracket on the right base of the stand and secure it 
with four hex bolts using the hex wrench.
4. Install the right controller bracket on the mounting bracket as shown, 
then tighten the screws.
5. Install the left mounting bracket onto the left base of the stand as 
shown, then secure it with four hex bolts.
Tighten screws
 

26
26|Setting Up the Printer
6. Hold the cushioning roller as shown and slide the left end onto the post 
on the left mounting bracket.
7. Slide the right end of the cushioning roller bracket onto the post on the 
right controller. Rotate the post base to align the holes, then secure the 
bracket using two hex bolts.
8. Place the right end of the scroller bar (the end with the metal collar) 
down between the rollers in the right controller. Then place the other 
end between the white rollers on the left...

27
Setting Up the Printer|27
Removing the Printer Packing Materials
Now you can remove the packing materials from the printer.
1. Remove all the tape and coverings from the printer.
2. Press in on the top of the maintenance covers to open them, then lift 
them off of the printer, and remove the protective coverings.
 

28
28|Setting Up the Printer
3. Place the maintenance cover hinges back in their slots and close the 
covers.
4. Remove any tape securing the back parts of the printer.
 

29
Setting Up the Printer|29
5. Open the front cover. Then remove the tape securing the paper holder 
plates, and the tape and brackets securing the carriage rail.
6. Remove both the bolt and bracket securing the print head. Save the bolt 
and bracket in case you need to ship the printer.
Caution: Remove the 
tape and brackets from 
the carriage rail slowly 
and carefully to avoid 
letting the tape touch any 
other part of the carriage.
Caution: Be sure to 
remove both the bracket 
and the bolt from the...

30
30|Setting Up the Printer
7. Attach the two cable supports to the leg of the stand as shown.
8. Rotate the feet counter-clockwise to raise them, then move the printer to 
the place of use. (Be sure to rotate the feet clockwise to stabilize the 
printer after moving it.)