Epson Stylus Pro 9880 User Manual

							191
Installing and Using Optional Equipment|191
5. Secure the manual cutter with the four screws you removed in step 2. 
If the cutter has three holes on each side, use the second and third holes 
from the top.
If the cutter has two holes on each side, use the lower hole on each side. 
Be sure to keep the other two screws.
6. When you are not using the cutter blade, slide it all the way to the left so 
it will not damage your printouts.
7. See the manual that came with the Manual Media Cutting System for 
instructions on using the cutter.
Removing the Manual Media Cutting System
Be sure to remove the manual cutter when you transport the printer.
1. Remove the screws securing the cutter to the printer.
2. Remove the cutter from the printer.
3. Replace the screws on the printer so you do not lose them.
 
						

							192
192|Installing and Using Optional Equipment
Using the Auto Take-Up Reel
To install the Auto Take-Up Reel, follow the instructions in the manual that 
came with it.
To use the paper guides packaged with the Auto Take-Up Reel, first remove 
the paper guides and holders that came with the printer, if you installed 
them. Then attach the paper guides packaged with the Auto Take-Up Reel.
The table below describes the status of the Auto Take-Up Reel as indicated 
by the 
Sensor light.
Sensor light statusDescription
On The Auto Take-Up Reel is ready to take in your printout.
Flashing The Auto Take-Up Reel sensor is not aligned; see 
page 199 to adjust the sensor.
Flashing rapidly The Auto Take-Up Reel has an error and stopped 
working; check the installation and see page 199 for 
additional solutions.
Off The Auto Take-Up Reel is turned off.
 
						

							193
Installing and Using Optional Equipment|193
Loading Roll Paper Onto the Take-Up Reel
Before you load roll paper onto the take-up reel core, check the following:
Turn off the Auto Take-Up Reel to avoid injury.
Make sure that the leading edge of the roll paper is straight.
Remove the center shaft from the upper basket hooks and the lower 
shafts from the holes on the bottom of the base, then place the paper 
basket under the printer.
Taking-Up Paper Forward
When you want paper wound onto the take-up reel with the print on the 
outside, set the take-up reel to wind paper forward, as described below.
1. Attach the three paper guides that came with the Auto Take-Up Reel, 
making sure to space them evenly.
2. Make sure that the roll paper is loaded in the printer properly. For 
instructions, see page 55.
3. Press the lbutton to select  (Auto Cut Off).
Warn i n g: Make sure the 
Auto Take-Up Reel is 
installed properly and is 
turned off before loading 
paper. If it is installed 
incorrectly or operates 
unexpectedly, bodily 
injury may occur.
 
						

							194
194|Installing and Using Optional Equipment
4. Press the dbutton to feed the roll paper out of the printer.
5. Set the 
Auto switch on the Auto Take-Up Reel to Off.
6. Tape the leading edge of the roll paper to the take-up reel core in three 
places.
 
						

							195
Installing and Using Optional Equipment|195
7. Press the d button to feed the paper forward and create some slack.
8. Hold the 
Manual switch on the Auto Take-Up Reel in the Forward 
position to take up at least one turn of paper onto the reel. Make sure 
adequate slack remains between the roll paper and the take-up reel.
Taking-up Paper Backward
When you want the paper wound onto the take-up reel with the print on the 
inside, set the take-up reel to wind paper backward, as described below.
1. Attach the three paper guides that came with the Auto Take-Up Reel, 
making sure to space them evenly.
2. Make sure that the roll paper is loaded in the printer properly. For 
instructions, see page 55.
 
						

							196
196|Installing and Using Optional Equipment
3. Press the lbutton to select  (Auto Cut Off).
4. Press the dbutton to feed the roll paper out of the printer.
5. Set the 
Auto switch on the Auto Take-Up Reel to Off.
6. Wind the bottom of the roll paper around the back of the reel as shown 
below, then tape the leading edge of the paper to the reel in three places.
 
						

							197
Installing and Using Optional Equipment|197
7. Press the d button to feed the paper forward and create some slack.
8. Hold the 
Manual switch on the Auto Take-Up Reel in the Backward 
position to take up at least one turn of paper on the take-up reel. Make 
sure adequate slack remains between the roll paper and the take-up reel.
 
						

							198
198|Installing and Using Optional Equipment
Printing Using the Auto Take-Up Reel
Once the Auto Take-Up Reel is installed and paper is attached to it, you can 
use it to take up your prints.
1. Press the lbutton to select  (Auto Cut Off).
2. Set the direction in which you loaded paper on the Auto Take-Up Reel 
using the 
Auto switch.
3. Send a print job to the printer. As the printer prints, the Auto Take-Up 
Reel takes up the roll paper 1/4 to 1/2 turn at a time as it feeds past the 
sensor.
4. When you are ready to remove your prints, turn off the Auto Take-Up 
Reel.
5. Press the l button to select  (Auto Cut On).
If you are printing on very thick paper, leave Auto Cut turned off, then 
feed and cut the paper manually to avoid damaging the cutter (see 
page 61). Continue with step 7.
6. Press and hold the   button for 3 seconds. The roll paper is cut 
automatically.
Warn i n g: Do not touch 
the Auto Take-Up Reel 
while it is operating; doing 
so may result in injury.
Do not look directly at the 
sensor beam across the 
front of the reel; doing so 
may cause permanent 
eye damage.
Turn off the Auto Take-Up 
Reel before removing the 
reel; if the reel operates 
unexpectedly, bodily 
injury may occur.
Caution: Do not place 
your hand or other object 
in the sensor detection 
area across the front of 
the reel. Interrupting the 
sensor beam can cause 
paper to be taken up 
under tension and 
adversely affect printing.
Do not touch the Manual 
switch while printing; 
doing so may damage 
your prints.
For paper wound forward 
(print winds on outside of reel)For paper wound backward 
(print winds on inside of reel)
 
						

							199
Installing and Using Optional Equipment|199
7. To remove your prints, turn the lever to unlock the reel, and then slide it 
left. Support the reel with one hand to keep it from falling.
8. Remove the take-up reel core from the paper stop on both ends of the 
reel.
Adjusting the Auto Take-Up Reel Sensor
If the Sensor light on the Auto Take-Up Reel is flashing, you need to adjust 
the sensor position.
1. Loosen the knob on the light emitter as shown below.
Caution:  Avoid placing 
the sensor in direct 
sunlight and prevent fans 
or air conditioners from 
blowing directly on the roll 
paper; otherwise, the auto 
take-up reel may not 
operate properly.
 
						

							200
200|Installing and Using Optional Equipment
2. Adjust the horizontal angle of the emitter until the Sensor light turns 
on, then tighten the knob to secure the emitter in position.