Epson Stylus Pro 9450 User Manual

Paper Handling211
Cutting the roll paper or printing page lines
When your print job is finished, the printer cuts the roll paper 
automatically or prints page lines around the printed data 
according to your settings. You can make these settings using the 
control panel or printer software.
Note:
❏Printer driver settings usually override the control panel settings. 
Use your printer driver settings whenever possible.
❏When the printer cuts the printout, it may take a little time to 
proceed with cutting...

Paper Handling212
4. If necessary, adjust the cutting position by using the Paper 
Feed d button or Paper Feed u button.
5. Cut the paper along the cutter guide using the manual cutter 
unit.
6. After cutting the paper, press the Pause   button. The printer 
becomes online.
Printing page lines
If you want to print continuously on roll paper and then cut the 
pages yourself after you finish printing, use the Print Page Line 
setting.
To make the Print Page Line setting using the control panel, see 
“PAGE...

Paper Handling213
Using the Auto Take-up Reel Unit
When you want to print your data on roll paper and do not want 
to cut it or feed it out onto the floor, you can use this optional Auto 
Take-up Reel Unit to roll up your printout.
See the Auto Take-up Reel Unit User’s Guide for information on 
installing the unit onto your printer.
Note:
❏Auto Take-up Reel Unit is designed for EPSON Stylus 
Pro 9880/9880C/9450 only.
❏When using the Auto Take-up Reel Unit, be sure to set the Auto 
Cut setting to off...

Paper Handling214
❏To use the paper guides packaged with the Auto Take-up Reel Unit, 
first remove the paper guides and holders packaged with the printer, 
as shown below. Then attach the paper guides packaged with the 
Auto Take-up Reel Unit, taking care to space them evenly.
Control box
The control box is located on the drive unit attached to the lower 
right side of the printer.
The roles of switches and meanings of the Sensor light are as 
follows.
Auto SwitchManual Switch
 

Paper Handling215 Sensor light
Switches
Adjusting the sensor
The angle of the sensors has already been adjusted when the unit 
is shipped. But, if the Sensor light on the control box is flashing, 
you need to adjust the sensor so that the light detector is aligned 
with the light emitter. When they are aligned, the Sensor light 
comes on.
c
Caution:
❏Avoid placing the sensor in direct sunlight; otherwise, the 
auto take-up reel unit may not operate properly.
❏Prevent fans or air conditioners from blowing...

Paper Handling216
1. Loosen the knob on the light emitter.
2. Adjust the horizontal angle of the emitter so that the Sensor 
light turns on.
3. Holding the detector in position, retighten the knob.
 

Paper Handling217
Loading roll paper onto the take-up reel core
w
Warning:
❏Turn off the Auto Take-up Reel Unit before loading paper. If 
the take-up reel unit operates unexpectedly, bodily injury 
may occur.
❏Make sure the take-up reel unit is installed properly and 
securely. Bodily injury may occur if it falls.
Before you load roll paper onto the take-up reel core, check the 
following:
❏Make sure that the leading edge of the roll paper is straight.
❏Be sure to remove the center shaft from the upper...

Paper Handling218 Winding paper forward
When you want paper wound onto the take-up reel core with the 
print on the outside, set the take-up reel unit to wind paper 
forward. Follow the steps below.
1. Attach the three paper guides packaged with the Auto 
Take-up Reel Unit, taking care to space them evenly.
2. Make sure that the roll paper is loaded in the printer properly. 
For instructions, see “Loading roll paper” on page 206.
3. Press the Paper Source l button to select Roll Auto Cut Off 
.
4.
Press...

Paper Handling219
5. Set the Auto switch on the control box to Off.
6. Tape the leading edge of the roll paper to the take-up reel core 
in three places.
 

Paper Handling220
7. Press the Paper Feed d button to feed the paper forward and 
create a loop of slack.
8. Move and hold the Manual switch on the Auto Take-up Reel 
Unit to the Forward position, and take up at least one turn of 
paper on the take-up reel core. Make sure that adequate slack 
remains between the roll paper and the take-up reel core.