Epson Stylus Pro 7890 User Manual

							201
Using the Optional Auto Take-Up Reel|201
Winding Prints Forward
1. Tape the leading edge of the paper to the take-up reel core in three 
places.
2. Press the d button to feed the paper forward and create some slack.
3. Set the 
Manual switch on the Auto Take-Up Reel to Forward and hold 
it long enough to take up at least three turns of paper onto the reel. 
Make sure adequate slack remains between the roll paper and the 
take-up reel.
Note: When printing on 
Singleweight Matte Paper 
at least 24 inches wide, 
place the tensioner in the 
slack area to ensure good 
print quality.
 
						

							202
202|Using the Optional Auto Take-Up Reel
Winding Prints Backward
1. Wind the bottom of the roll paper around the back of the reel as shown 
below, then tape the leading edge of the paper to the reel in three places.
2. Press the d button to feed the paper forward and create some slack.
3. Set the 
Manual switch on the Auto Take-Up Reel to Backward to take 
up at least three turns of paper onto the reel. Make sure adequate slack 
remains between the roll paper and the take-up reel.
 
						

							203
Using the Optional Auto Take-Up Reel|203
Printing Using the Auto Take-Up Reel
Once the Auto Take-Up Reel is installed and paper is attached to it, you can 
use it to take up your prints.
1. Set the 
Auto switch to Forward or Backward, depending on how you 
set up the paper.
2. Send a print job to the printer. The Auto Take-Up Reel takes up the roll 
paper 1/4 to 1/2 turn at a time.
3. When you are ready to remove your prints, set the 
Auto switch to Off.
4. Press the   button on the printer to cut the paper.
WARNING: Do not touch 
the Auto Take-Up Reel 
while it is operating; doing 
so may result in injury.
Turn off the Auto Take-Up 
Reel before removing the 
reel; if the reel operates 
unexpectedly, bodily 
injury may occur.
 
						

							204
204|Using the Optional Auto Take-Up Reel
5. To remove your prints, turn the lever to unlock the reel, and then slide it 
left. Support the reel with one hand to keep it from falling.
6. Remove the take-up reel core from the paper stop on both ends of the 
reel.
Reversing the Paper Stops for a 2-inch Paper Reel Core
You can use a 2-inch roll paper core (after the paper is used up) in the auto 
take-up reel. First you need to reverse the paper stops.
1. Remove the paper stop from the drive unit by pinching the clips.
3
2
 
						

							205
Using the Optional Auto Take-Up Reel|205
2. Reverse the paper stop so that the smaller knob is on the outside. Then 
pinch the clip and reinstall the paper stop on the drive unit.
3. Remove the paper stop from the movable unit by pinching the knob.
 
						

							206
206|Using the Optional Auto Take-Up Reel
4. Reverse the paper stop so that the smaller knob is on the outside. Then 
pinch the knob and reinstall the paper stop on the movable unit.
Installing a Take-Up Reel Core
1. Make sure the lock lever is released. Then slide the movable paper stop 
all the way to the left.
 
						

							207
Using the Optional Auto Take-Up Reel|207
2. Slip one end of the take-up reel core over the paper stop on the drive 
unit.
3. Insert the paper stop on the movable unit into the other end of the core.
 
						

							208
208|Using the Optional Auto Take-Up Reel
4. Turn the lever to the front to lock the movable unit.
 
						

							209
209
This Appendix summarizes the functions of the control panel’s lights and 
buttons (below), describes the informational messages and icons you may see 
on the LCD screen (see page 212), and lists the available menu settings (see 
page 213).
Control Panel Buttons and Lights
Buttons
ButtonDescription
PPower Turns the printer on and off
Pause/reset Stops printing temporarily
Restarts printing when printing was paused
In menu mode, returns the printer to READY state
When held for 3 seconds, deletes the print job
rMenuAccesses the printer menus
Selects menus and settings within menu mode
During printing, enters the PRINTER STATUS menu
lPaper Source Selects the paper source ( sheet,  roll/Auto Cut 
On, or  roll/Auto Cut Off)
Goes back to previous menu within menu mode
Appendix C:  
Control Panel
LCD 
screen
Power 
light and 
button
Pause/reset 
light and buttonInk 
light
Left arrow or paper 
source button Paper 
light
Menu button
Paper feed up button
Paper feed down buttonOK button
Paper cut 
button
Ink open button
Black ink change buttonPaper release (ePlaten) 
light and button
 
						

							210
210|Control Panel
dPaper feed Down Feeds the paper forward. Press and hold to feed paper 
faster.
When paper is unlocked, reduces paper suction
Changes setting parameters within menu mode
uPaper feed Up Feeds the paper backward
When paper is unlocked, increases paper suction
Changes setting parameters within menu mode
OK Executes setting changes within the menu system
When held for 3 seconds when  sheet is selected, 
ejects the sheet
When no paper is loaded, displays paper loading 
procedures on the LCD screen
When held for 3 seconds when the printer is drying ink, 
stops the ink drying process and ejects the paper
 Black ink change Switches from Photo Black to Matte Black and 
vice-versa. For more information, see page 157.
 Ink open Opens the selected ink cover
Paper release or 
ePlatenLocks or releases paper in the printer
 Paper cut Cuts roll paper
ButtonDescription