Epson Stylus Pro 7700 User Manual

161
Maintaining and Transporting the Printer|161
Changing the Date and Time
1. Press r Menu.
2. Press d until 
MAINTENANCE is highlighted, then press r.
3. Press d until you see 
CLOCK SETTING, then press r.
4. Use the d, u, and r buttons to set each item in the date and time, 
displayed in the following format: 
MM/DD/YY HH:MM.
5. Press 
OK to save the setting.
Using Maintenance Mode
Maintenance mode allows you to make special settings and perform 
maintenance procedures that may be needed occasionally....

162
162|Maintaining and Transporting the Printer

To change the units of measurement, press d to highlight LENGTH 
UNITS
, then press r. Press d to switch from METRIC to 
FEET/INCH, then press OK to select it. Press l when done.
To change the temperature units of measurement, press d to 
highlight 
TEMPERATURE UNITS, then press r. Press d to switch 
from 
C (Celsius or centigrade) to F (Fahrenheit), then press OK to 
select it. Press 
l when done.
To change the maximum roll paper tension, press d to...

163
Maintaining and Transporting the Printer|163
3. Press d until CUTTER REPLACEMENT is highlighted, then press r 
again.
4. Press 
OK. The paper cutter moves to the replacement position.
5. To remove the cutter cover, press in the tab and pull it down.
6. Loosen the screw using a cross-head screwdriver.
 

164
164|Maintaining and Transporting the Printer
7. Carefully remove the cutter.
8. Dispose of the cutter in accordance with local regulations.
Installing the New Cutter
Remove the new blade from its package, then follow these steps to install it:
1. Insert the new cutter into the holder. Make sure the cutter pin goes into 
the hole.
WARNING: The blade is 
sharp. Be careful when 
removing it. 
 

165
Maintaining and Transporting the Printer|165
2. Tighten the screw using a cross-head screwdriver.
3. Align the cover, then press it in until it clicks into place.
4. Press 
OK to finish the replacement process. The cutter moves to home 
position.
5. Run the Cutter Adjustment from the Maintenance Menu on the control 
panel.
After you print the pattern, put the two cut pieces together and select 
the pattern with the most precise cut between the two colors. Select the 
pattern number on the control...

166
166|Maintaining and Transporting the Printer
Replacing the Maintenance Tank
The maintenance tank stores ink that gets flushed from the system during 
the initial ink charge and manual and automatic print head cleaning. When 
the tank is almost full, the message 
MAINTENANCE TANK NEARLY FULL 
appears on the LCD display. When the tank is completely full, the printer 
stops working and 
MAINTENANCE TANK FULL appears on the LCD.
You can check how much space remains in the maintenance tank by viewing 
its...

167
Maintaining and Transporting the Printer|167
3. Grasp the handle at the bottom of the tank (on the side of the printer) 
and gently pull out the maintenance tank. Then place it in the plastic 
bag included with the new tank.
4. Insert the new tank.
Caution: Be careful not 
to spill ink from the 
maintenance tank when 
removing it. Hold it upright 
at all times and dispose of 
it carefully. 
 

168
168|Maintaining and Transporting the Printer
Cleaning the Printer
To keep your printer working at its best, clean it if it becomes soiled.
1. If your prints are soiled by ink on the roller, load inexpensive roll paper 
and press d to feed the paper without printing on it. Press d several 
times until the paper is clean. 
2. Turn off the printer and wait until all the lights are off. Then unplug the 
power cord and disconnect the printer from your system.
3. Open the front cover and use canned air or...

169
Maintaining and Transporting the Printer|169
5. If your prints are soiled on the back, wipe the blue area carefully.
6. If powdery dust has accumulated, use a toothpick or similar tool to 
remove it.
7. Remove the paper basket. Then clean away any dust or dirt around the 
leg assembly using a soft brush.
 

170
170|Maintaining and Transporting the Printer
8. If the outer case is dirty, clean it with a soft, clean cloth dampened with 
mild detergent. Keep the ink cartridge compartments closed to prevent 
water from getting inside.
9. To wash the paper basket, remove the shafts, then machine wash with 
mild detergent and air dry.
Transporting or Storing the Printer
If you are moving the printer a short distance (for example, in the same 
building), you can roll it on its stand (see page 172). To ship the...