Epson Projector PowerLite Home Cinema 600 User Manual

Projector Information Display - Info Menu
You can display information about the projector and input sources by viewing the Info menu. However,
you cannot change any settings in the menu.
Note:Available settings depend on the current input source. The lamp usage timer does not register any
hours until you have used the lamp for at least 10 hours.
Information item Description
Lamp Hours Displays the number of hours (H) the lamp has been used in
Normal andECO Power Consumption modes; if the information is...

Information item
Description
Status Displays information about projector problems that may be needed
by a service technician
Serial Number Displays the projectors serial number
Event ID Displays the Event ID number corresponding to a specific projector
problem; see the list of Event ID codes
Event ID Code List
Parent topic: Adjusting the Menu Settings
Related references
Optional Equipment and Replacement Parts
Projector Lamp Specifications
Event ID Code List If theEvent ID option on the Info menu...

Event ID code Cause and solution
0479
A projector system error has occurred. Turn the projector off and then on again.
04FF
0891 Cannot find an access point with the same SSID. Set your computer, access point,
and projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Make sure the wireless
network security settings are correct.
0893 The WEP/TKIP/AES encryption type does not match. Make sure the wireless
network security settings are correct.
0894 Communication with...

Projector Reset Options - Reset Menu
You can reset most of the projector settings to their default values using the Reset Alloption on the
Reset menu.
You cannot reset the following settings using the Reset Alloption:
• Input Signal
• Users Logo
• Language
• Network menu items
• Lamp Hours
• Password
• Zoom
Parent topic: Adjusting the Menu Settings
114 

Maintaining and Transporting the Projector
Follow the instructions in these sections to maintain your projector and transport it from place to place.
Projector Maintenance
Transporting the Projector
Projector Maintenance Your projector needs little maintenance to keep working at its best.
You may need to clean the lens periodically, and clean the air filter and air vents to prevent the projector
from overheating due to blocked ventilation.
The only parts you should replace are the lamp, air filter, and...

• To remove stubborn smudges, moisten a soft, lint-free cloth with lens cleaner and gently wipe the
lens. Do not spray any liquid directly on the lens.
Warning: Do not use a lens cleaner that contains flammable gas. The high heat generated by the
projector lamp may cause a fire.
Caution: Do not use glass cleaner or any harsh materials to clean the lens and do not subject the lens
to any impacts; you may damage it. Do not use canned air, or the gases may leave a residue. Avoid
touching the lens with your...

Related references
Projector Light Status
Cleaning the Air Filter and Vents Clean the projectors air filter or vents if they get dusty, or if you see a message telling you to clean them.
1. Turn off the projector and unplug the power cord.
2. Gently remove the dust using a small vacuum designed for computers or a very soft brush (such asa paintbrush).
Note: You can remove the air filter so you can clean both sides of it. Do not rinse the air filter in
water, or use any detergent or solvent to clean it....

1. Turn off the projector and unplug the power cord.
2. Carefully open the air filter cover.
3. Pull the air filter out of the projector.
118   

Note:
Air filters contain ABS resin and polyurethane foam. Dispose of used air filters according to
local regulations.
4. Place the new air filter in the projector as shown and push gently until it clicks into place.
5. Close the air filter cover.
Parent topic: Air Filter and Vent Maintenance
Related references
Optional Equipment and Replacement Parts
Related tasks
Cleaning the Air Filter and Vents
Projector Lamp Maintenance The projector keeps track of the number of hours the lamp is used and displays...

Replacing the Lamp
Resetting the Lamp Timer
Parent topic:
Projector Maintenance
Related references
Optional Equipment and Replacement Parts
Projector Information Display - Info Menu
Projector Lamp Specifications
Replacing the Lamp Before you replace the lamp, let the projector cool down for at least one hour so the lamp will not be hot.
Warning:Let the lamp fully cool before replacing it to avoid injury.
You can replace the lamp while the projector is mounted to the ceiling, if necessary.
1. Turn off the...