Epson Projector PowerLite 4650 User Manual

							

If
you want tooutput audiofromtheexternal speakers whentheprojector isturned off,you need to
 select
Communication Onforthe Standby Modesetting andAlways Onforthe AVOutput settingin
 the
projectors Extendedmenu.
 Note:
Theprojectors built-inspeaker systemisdisabled whenyouconnect external speakers.
 1.
Make sureyourcomputer orvideo source isconnected tothe projector withboth audio andvideo
 cables
asnecessary.
 2.
Locate theappropriate cabletoconnect yourexternal speakers, suchasastereo mini-jack-to-pin-
 jack
cable, oranother typeofcable oradapter.
 3.
Connect oneendofthe cable toyour external speakers asnecessary.
 4.
Connect thestereo mini-jack endofthe cable toyour projectors AudioOutport.
 Parent
topic:Projector Connections
 Attaching
andRemoving theCable Cover
 You
canattach thecable cover thatcame withyour projector tohide theattached cablesfromview.
 41  
						

							

1.
Bundle thecables together usingaband orother fastener (notprovided).
 2.
Place thecable cover onthe projector asshown, guiding thecables through thenotch onthe base of
 the
cable cover.
 42   
						

							

3.
Tighten bothcable cover screws.
 To
remove thecover, loosen bothscrews andtake thecover offofthe projector.
 Parent
topic:Setting Upthe Projector
 Attaching
andRemoving theHDMI Cable Clip
 You
caninstall theHDMI cableclipthat came withyour projector toprovide additional supporttothe
 HDMI
cable.
 1.
Plug inthe HDMI cable.
 43  
						

							

2.
Insert theend ofthe cable clipanchor intothecable clipslot near theHDMI portasshown.
 1
 Cable
clipslot
 2
 Cable
clipanchor
 3
 Cable
clip
 3.
Place theopen cable cliparound theHDMI cable, butdont lockitinto place.
 4.
Slide thecable cliponto theanchor andlock theclip onto theHDMI connector asshown.
 To
remove thecable clip,open theclip and disconnect theHDMI cable. Thenpinch thesides ofthe
 cable
clipanchor andcarefully pullitout ofthe cable clipslot.
 Parent
topic:Setting Upthe Projector
 Related
tasks
 Connecting
toaComputer forHDMI Video andAudio
 Connecting
toan HDMI Video Source
 Installing
Batteriesinthe Remote Control
 The
remote controlusesthetwo AAbatteries thatcame withtheprojector.
 44  
						

							

Caution:
Useonly thetype ofbatteries specified inthis manual. Donot install batteries ofdifferent types,
 or
mix new andoldbatteries.
 1.
Open thebattery cover.
 2.
Insert thebatteries withthe+and –ends facing asshown.
 45   
						

							

3.
Close thebattery coverandpress itdown untilitclicks intoplace.
 Warning:
Disposeofused batteries according tolocal regulations. Donot expose batteries toheat
 or
flame. Keepbatteries outofthe reach ofchildren; theyarechoking hazards andarevery
 dangerous
ifswallowed.
 Parent
topic:Setting Upthe Projector
 46  
						

							

Using
theProjector onaNetwork
 Follow
theinstructions inthese sections toset upyour projector foruse onanetwork.
 Wired
Network Projection
 Wireless
NetworkProjection
 Setting
UpProjector NetworkE-MailAlerts
 Setting
UpMonitoring UsingSNMP
 Controlling
aNetworked ProjectorUsingaWeb Browser
 Crestron
RoomView Support
 Wired
Network Projection
 You
cansend images toyour projector throughawired network. Todothis, youconnect theprojector to
 your
network, andthen setupyour projector andcomputer fornetwork projection.
 After
connecting andsetting upthe projector asdescribed here,install thenetwork software fromthe
 Epson
Projector SoftwareCD-ROM onyour computer. Usethefollowing softwareanddocumentation to
 set
up, control, andmonitor network projection:
 •
EasyMP Network Projection softwaresetsupyour computer fornetwork projection. Seethe
 EasyMP
NetworkProjection OperationGuideforinstructions.
 •
EasyMP Monitorsoftware (Windows only)letsyou monitor andcontrol yourprojector throughthe
 network.
Youcandownload thelatest software anddocumentation fromtheEpson website. Goto
 www.epson.com/support
(U.S.)orwww.epson.ca/support (Canada)andselect yourprojector.
 •
EasyMP Network Updatersoftware(Windows only)allows youtoupdate firmware foraprojector
 over
awired LAN.SeetheEasyMP NetworkUpdaterOperation Guideforinstructions. Youcan
 download
thelatest software anddocumentation fromtheEpson website. Goto
 www.epson.com/support
(U.S.)orwww.epson.ca/support (Canada)andselect yourprojector.
 Note:
Ifyour projector isconnected viaaLAN cable toanetwork thatincludes awireless accesspoint,
 you
canconnect tothe projector wirelessly throughtheaccess pointusing theEasyMP Network
 Projection
software.
 Connecting
toaWired Network
 Selecting
WiredNetwork Settings
 Parent
topic:UsingtheProjector onaNetwork
 47 
						

							

Connecting
toaWired Network
 To
connect theprojector toawired localareanetwork (LAN),usea100Base-TX or10Base-T network
 cable.
Toensure properdatatransmission, useaCategory 5eshielded cableorbetter.
 1.
Connect oneendofthe network cabletoyour network hub,switch, orrouter.
 2.
Connect theother endofthe cable tothe projectors LANport.
 Note:
Thelocation ofthe LAN portmay differ depending onthe projector model.
 Parent
topic:WiredNetwork Projection
 Selecting
WiredNetwork Settings
 Before
youcanproject fromcomputers onyour network, youmust select thenetwork settingsforthe
 projector
usingitsmenu system.
 Note:
Makesureyoualready connected theprojector toyour wired network usingtheLAN port.
 1.
Turn onthe projector.
 2.
Press theMenu button.
 48  
						

							

3.
Select theNetwork menuandpress Enter.
 4.
Select Network Configuration andpress Enter.
 5.
Select theBasic menuandpress Enter.
 6.
Select thefollowing basicoptions asnecessary:
 •
Projector Nameletsyou enter aname upto16 alphanumeric characterslongtoidentify the
 projector
overthenetwork.
 49 
						

							

•
PJLink Password letsyou enter apassword upto32 alphanumeric characterslongforusing the
 PJLink
protocol forprojector control.
 •
Web Control Password letsyou enter apassword upto8alphanumeric characterslongfor
 accessing
theprojector overtheweb.
 •
Projector Keywordletsyou turn onasecurity password toprevent accesstothe projector by
 anyone
notinthe room withit.You must enter adisplayed, randomized keywordfromacomputer
 using
theEasyMP NetworkProjection softwaretoaccess theprojector.
 Note:
Usethedisplayed keyboardtoenter thename, passwords andkeyword. Pressthearrow
 buttons
onthe remote controltohighlight characters andpress Enter toselect them.
 7.
Select theWired LANmenu andpress Enter.
 8.
Ifnecessary, selectIPSettings andpress Enter.
 9.
Select yourIPSettings asnecessary:
 •
Ifyour network assignsaddresses automatically, turnonthe DHCP setting.
 •
Ifyou must setaddresses manually,turnoffDHCP andenter theprojectors IPAddress ,Subnet
 Mask
,and Gateway Addressasneeded.
 Note:
Tohighlight thenumbers youwant fromthedisplayed keyboard, pressthearrow buttons on
 the
remote control. Toselect ahighlighted number,pressEnter.
 50