Epson Projector Powerlite 1810p User Manual

							Welcome11
Optional Accessories 
To enhance your use of the projector, Epson provides the following 
optional accessories:  
You can purchase screens or other accessories from an Epson 
authorized reseller. To find the nearest reseller, call 800-GO-EPSON 
(800-463-7766). Or you can purchase online at www.epsonstore.com
 
(U.S. sales) or www.epson.ca
 (Canadian sales).
Product Part number
Replacement lamp  V13H010L40
Air filter replacement set (2 filters) V13H134A08
Universal ceiling mount 
False ceiling plate
Security bracket/cabling for gyro lock mounts
Adjustable ceiling channel
Suspension adapter ELPMBUNI
ELPMBFCP
ELPMBSEC
ELPMBACC
ELPMBAPL
Kensington
® security lock  ELPSL01
50-inch portable screen (4:3 aspect ratio)
60-inch portable pop-up screen (4:3 aspect ratio)
80-inch portable pop-up screen (4:3 aspect ratio)
83.6-inch hanging pull-down screen (4:3 aspect ratio)
DUET Portable Projector Screen (4:3/16:9 combination)ELPSC06
ELPSC07
ELPSC08
ELPSC09
ELPSC80
HD-15 to component video cable
S-video cable ELPKC19
ELPSV01
Distribution amplifier ELPDA01
Image presentation camera (ELPDC05) V12H162020 
						

							12Welcome 
						

							13
1
Displaying and Adjusting 
the Image
Whether you’re presenting from a computer or video equipment, 
you need to follow some basic steps to display your image on the 
screen. 
Follow the guidelines in this chapter for: 
■Positioning the projector
■Turning on and off the projector 
■Displaying an image
■Troubleshooting display problems
■Adjusting the image 
						

							14Displaying and Adjusting the Image
Positioning the Projector 
If the projector isn’t already installed in the room you’re using, you’ll 
probably want to place it on a table in front of the screen, as shown. 
This lets you stand in the front of the room, face the audience, and 
remain close enough to the equipment to be able to control it. Try to 
leave as much space as possible between the projector and the screen to 
get a good-size image. 
Use the figure below to help you determine placement. Image size 
increases with distance, but can vary depending on how you position 
the zoom ring and whether you’ve adjusted the image with other 
settings. 
Also keep these considerations in mind: 
■Place the projector on a sturdy, level surface.
■Make sure there is plenty of space for ventilation around and 
under the projector. Do not set the projector on top of anything 
that could block the vents under the projector. 
■Make sure the projector is within 10 feet of a grounded electrical 
outlet or extension cord. 
note
You can mount the projector 
on the ceiling, or place it 
behind a translucent screen 
for rear projection. See 
page 87 for details.
2.7 to 4.6 ft 5.7 to 9.4 ft 29.7 to 48.2 ft Distance from screen
 TBD 
						

							Displaying and Adjusting the Image15
Ideally, you should place the projector directly in front of the center of 
the screen, facing it toward the screen squarely. The base of the lens 
should be at about the level of the bottom of the screen. 
If you place the projector below screen level, you’ll have to tilt it up by 
extending the front adjustable foot. This causes the image to become 
“keystone” shaped, but you can correct the distortion (see page 22). 
For instructions on installing the projector in a permanent location, 
such as a theater or conference room, see page 87.
Turning On and Off the Projector
Turn on any connected computer or video equipment before starting 
the projector so it can automatically detect and display the image 
source. If you turn on the projector first, or have multiple pieces of 
connected equipment, you may have to select the image source 
manually (see page 18). 
note
After positioning the 
projector, you may want to 
connect a Kensington 
MicroSaver
® anti-theft 
device to the lock port on the 
projector. You can purchase 
this from Epson; see 
page 11. 
Screen
Projector 
						

							16Displaying and Adjusting the ImageFollow these steps to turn on the projector: 
1. Open the A/V mute slide (lens cover). 
2. Plug one end of the power cable into the projector, and the other 
end into an electrical outlet.
The 
Power light turns orange. 
note
You can set the projector to 
automatically turn off the 
projector lamp and enter 
“sleep mode” when it has 
not received any signals for 
30 minutes. This conserves 
electricity, cools the 
projector, and extends the 
life of the lamp. If you want 
to start projecting again, 
press the 
P Power button. 
If you are done using the 
projector, unplug the power 
cord. To enable sleep mode, 
see page 60. 
Power light 
						

							Displaying and Adjusting the Image17
3. Press the PPower button on the remote control or on top of the 
projector. 
The projector beeps once and the 
Power light flashes green as the 
projector warms up, then an image begins to appear. When the 
Power light stops flashing and remains green, the projector is 
ready for use. 
4. If you are prompted to enter a password, see page 57.
Using the Direct Power On Function
The Direct Power On function enables faster setup. The projector 
starts up automatically when you plug it in or turn it on with a wall 
switch. You don’t have to press the P
Power button. 
Follow these steps to enable Direct Power On: 
1. Press the 
Menu button on the remote control or projector and 
select the 
Extended menu. 
2. Choose 
Operation and press Enter. 
3. Choose 
Direct Power On and press Enter.
4. Highlight 
On and press Enter. 
5. Press 
Menu to exit. The setting will take effect the next time you 
plug in the projector.
warning
Never look into the lens 
when the lamp is on. This 
can damage your eyes, and is 
especially dangerous for 
children.
note
If a power outage occurs 
when Direct Power On is 
enabled and the projector is 
plugged in, the projector will 
start when the power is 
restored. 
						

							18Displaying and Adjusting the Image
Shutting Down the Projector
This projector incorporates Instant Off technology. To turn it off, you 
can press its P
Power button as described below, unplug it, or turn 
off a power switch that supplies power to the projector. You don’t 
have to wait for the projector to cool off first. 
1. To turn off the projector, press the P
Power button on the 
remote control or projector. 
You see a confirmation message. 
(If you don’t want to turn it off, 
press any other button.)
2. Press the P
Power button again. The 
projection lamp turns off and you can unplug the power cord. 
If you want to turn the projector on again, make sure the orange 
Power light is not flashing, then press the PPower button.
Displaying an Image
You may need to select the image source if you have multiple video 
sources connected to the projector (such as a computer or DVD 
player). Selecting the image source lets you switch between images 
input from different pieces of connected equipment. 
If you don’t see the image you want, press the 
Search button on the 
remote control or the 
Source Search button on the projector until 
you see the image you want to project. 
You can also use the 
Source buttons on the remote control to switch 
between devices connected to the ports identified on each button. The 
PowerLite 1810p does not support EasyMP.
TM 
note
Lamp life results will vary 
depending on mode selected, 
environmental conditions, 
and usage.
Turn off this product when 
not in use to prolong the life 
of the projector.  
						

							Displaying and Adjusting the Image19
Troubleshooting Display Problems
Follow these guidelines if you’re having trouble displaying an image. 
You Can’t Project an Image
If you don’t see the image you are trying to project, try the following: 
■Make sure the cables are connected correctly, as described 
beginning on page 35.
■Make sure the Power light is green and not flashing and the A/V 
mute slide (lens cover) is open. 
■If you’ve connected more than one computer and/or video source, 
you may need to press the 
Source Search button on the 
projector’s control panel or 
Search button on the remote control 
to select the correct source. (Allow a few seconds for the projector 
to sync up after pressing the button.)
■If you’re using a PC notebook, press the function key on your 
keyboard that lets you display on an external monitor. It may be 
labeled 
CRT/LCD or have an icon such as  . You may have to 
hold down the 
Fn key while pressing it. Allow a few seconds for 
the projector to sync up after changing the setting. 
The Projector and Notebook Don’t Display the 
Same Image
If you’re projecting from a notebook, and you can’t see your image on 
the projection screen and on your computer at the same time, follow 
these guidelines.
If you’re using a PC notebook:
■On most systems, there’s a function key that lets you toggle 
between the LCD screen and the projector, or display on both at 
the same time. It may be labeled 
CRT/LCD or have an icon such as 
. You may have to hold down the 
Fn key while pressing it. 
Allow a few seconds for the projector to sync up after changing 
the setting.  
						

							20Displaying and Adjusting the Image
■If the function key doesn’t permit you to display simultaneously 
on both screens, you should check your monitor settings to make 
sure both the LCD screen and the external monitor port are 
enabled. 
From the Control Panel, open the 
Display utility. In the Display 
Properties dialog box, click the 
Settings tab, then click 
Advanced. The method for adjusting the settings varies by 
brand; you may need to click a 
Monitor tab, then make sure the 
external Monitor port is set as your primary display and/or 
enabled. See your computer’s documentation or online help for 
details. 
If you’re using Mac OS X:
You may need to set up your system to display on the projector screen 
as well as the LCD screen. Follow these steps:
1. From the Apple
® menu, select System Preferences, then select 
Displays.
2. Make sure the 
VGA Display or Color LCD dialog box is selected.
3. Click the 
Arrangement (or Arrange) tab.
4. Make sure the 
Mirror Displays checkbox is selected. 
Make sure 
Mirror Displays 
is checked