Epson Projector Powerlite 1710c User Manual

Fine-Tuning the Projector51
The default setting for the Password Protect function is Off. Follow 
these steps to turn password protection on:
1. Press the 
Freeze button on the remote control for about five 
seconds.
You see this screen:
2. Use the   pointer button to set 
Power On Protect to On. Then 
press 
Enter.
3. Press 
Esc.
4. Select Password and press Enter.
5. When you see a message asking if you want to change the 
password, select 
Yes and press Enter.
6. Hold down the 
Num button on the...

52Fine-Tuning the ProjectorThe countdown for the elapsed time begins as soon as you close 
the Password Protect menu. (You can check the elapsed time in 
this menu next to 
Time elapsed.)
10. To enable your screen logo, select 
User’s Logo Protect and press 
Enter. Select On and press Enter. 
When this feature is on, the logo appears whenever you turn on 
the projector (if the 
Startup Screen is enabled in the Extended 
menu; see page 53). It also appears when you press the A/V Mute 
button (if you...

Fine-Tuning the Projector53
If the password is not correct, you see a message prompting you to 
re-enter the password. If you enter an incorrect password three times 
in succession, you see the message 
The projector’s operation will be 
locked. Request code xxxxx
 and the projector switches to standby 
mode for approximately 5 minutes. Write down the request code. 
Then disconnect the projector’s power cord from the electrical outlet, 
reconnect it, and turn the projector back on. 
When you see the...

54Fine-Tuning the Projector2. Highlight 
User’s Logo and press Enter. 
3. When you see a message asking 
Choose this image as the 
user’s logo?
, select Yes and press Enter. A selection box displays 
over the image. 
4. Use the  pointer button to select the area of the image you 
want to use. Then press 
Enter.
5. When you see the message 
Select this Image?, highlight Yes 
and press 
Enter. 
6. Use the arrow buttons to select a zoom rate (display size) and press 
Enter.
7. When the message 
Save this...

Fine-Tuning the Projector55
2. Select Display and press Enter.
3. Highlight 
Display Background (for when there is no signal) or 
A/V Mute, and press Enter. 
4. Select 
Logo and press Enter.
5. When you’re finished, press Esc to exit.
Disabling the Projector’s Buttons
When you enable the Operation Lock function, you can lock all the 
projector’s buttons, or all buttons except the 
Power button.
1. Press the 
Menu button, highlight the Settings menu, and press 
Enter.
2. Select 
Operation Lock and press...

56Fine-Tuning the Projector
■Display
Use this setting to turn off the display of messages, change the 
background color, enable logo display, or turn off the startup 
screen display.
■User’s Logo
Create a custom startup screen, as described on page 53.
■Projection 
Select Front (to project from the front of a screen and right side 
up), 
Front/Ceiling (when the projector is mounted upside-down 
from the ceiling), 
Rear (to project from behind onto a 
transparent screen), or 
Rear/Ceiling (to project from...

57
1
Maintaining the Projector
Your projector needs little maintenance. All you have to do is keep 
the lens clean and periodically clean the air filter and vent. A clogged 
air filter or vent can block ventilation needed to cool the projector.
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■Cleaning the lens
■Cleaning the projector case
■Cleaning the air filter and vent...

58Maintaining the Projector
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
Use a canister of compressed air to remove dust.
To remove dirt or smears on the lens, use lens-cleaning tissue. If 
necessary, moisten a soft cloth with lens cleaner and gently wipe the 
lens.
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power 
cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free 
cloth.
■To remove stubborn dirt...

Maintaining the Projector59
Cleaning the Air Filter and Vent
Clean the air filter and air intake vent after every 100 hours of use. If 
they are not cleaned periodically, they can become clogged with dust, 
preventing proper ventilation. This can cause overheating and damage 
the projector. 
Follow these steps:
1. Turn off the projector. Wait for the 
Power light to stop flashing, 
then unplug the power cord.
2. Turn the projector upside down.
3. To clean the intake vent and filter, use a small vacuum...

60Maintaining the Projector
Replacing the Lamp and Air Filter
The life span of the projection lamp is about 2000 hours if 
Brightness Control in the Setting menu is set to High (default), and 
3000 hours if 
Brightness Control is set to Low. 
It is time to replace the lamp when: 
■The projected image gets darker or starts to deteriorate.
■The message Replace the lamp appears on the screen when the 
lamp comes on and the lamp warning light   flashes orange. To 
maintain projector brightness and image...