Epson Projector L1505U User Manual

171
12. Select the input signal to display an image.
After performing the steps here, adjust the images for any gaps and differences in color.
Note:
Do not change any of the projector names or IP addresses, or the images will not be adjusted
automatically.
Parent topic: Tiling Images into One Image
Related references
Projector Parts - Front/Top
Related tasks
Configuring Tiling Manually
Configuring Tiling Manually If your projectors are not on a network or you were unsuccessful tiling the images...

172
7. Select
Location Setup and pressEnter.
8. Select the position of each projected image as follows: •Row Order to layout the screens from top to bottom in sequential order, starting with 1at the top
• Column Order to layout the screens from left to right, starting with Aon the left
9. Repeat the previous step with each projector you are setting up before continuing with the next step.
10. Select the input signal to display an image.
After performing the steps here, adjust the images for any gaps and...

173
Blending the Image Edges
You can use the projectors Edge Blending feature to create a seamless image from multiple projectors.
1. Press theMenubutton.
2. Select the Extendedmenu and press Enter.
3. Select the Multi-Projection setting and pressEnter.
4. Select the Edge Blending setting and press Enter.
You see this screen:
5. Turn on the Edge Blending, Guide Display, and Pattern Guidesettings.
Note: If the projected guide is unclear, try changing the Guide Colorssetting.
6. Select the edge you want to...

174
You see a screen like this:
7. Select the Blendingsetting and select On.
8. Select the Blend Start Position setting and adjust the point where edge blending begins.
9. Select the Blend Rangesetting and select the width of the blended area so that the displayed
guides are at the edges of the overlapping area between the two images.
10. Press Escto go back to the previous screen.
11. Select the Blend Curvesetting and select a gradient for the shaded area.
12. When the edges are blended, turn off the...

175
Adjusting the Black Level
When two images overlap, the overlapping area can appear differently from the areas that do not
overlap. You can use the projectors Black Level setting to make the difference less noticeable.
Note:You may not be able to adjust the black levels correctly if the Geometry Correctionsettings are
set too high. The brightness and tone of the overlapping areas may differ from the rest of the image even
after adjusting the black level.
1. Press the Menubutton.
2. Select the...

176
You see this screen:
5. Select the Color Adjustment setting and pressEnter.
You see a screen based on the Top Edge,Bottom Edge, Right Edge, and Left Edgesettings you
selected for the Edge Blending setting.
Note: TheColor Adjustment setting is automatically adjusted when selecting Start Auto
Adjustment in the Screen Matching screen. 

177
6. Select the area you want to adjust and press
Enter.
Note: The area you selected is displayed in orange. Adjust overlapping areas starting with the
brightest areas first. For example, adjust area 2 to match area 1, then adjust area 3 to match area 2.
7. Adjust the brightness and tone of the areas that do not overlap to match the areas that overlap using the displayed adjustment sliders.
8. Repeat the previous two steps as needed until all areas match.
9. If the tone of some areas do not match, you...

178
You see a screen like this displaying the points you can use to set the adjustment range:
14. Use the arrow buttons to adjust the boundary line position and press the Enterbutton.
15. Use the arrow buttons to select an adjustment point and press the Enterbutton.
The selected point turns orange.
16. Use the arrow buttons to move the point.    

179
17. To move another point, press the
Escbutton and repeat the previous two steps.
18. To move another boundary line, press the Escbutton repeatedly until you can select a boundary
line.
19. When you are finished, press the Menubutton.
Note: Changing the Top Edge,Bottom Edge, Right Edge, or Left Edgesettings resets the Black
Level setting to its default value.
Parent topic: Using Multiple Projectors
Related references
Projector Setup Settings - Extended Menu
Matching Tint and Brightness (Screen...

180
• All the projectors are connected to a network and the
Location Setupsetting has been configured.
• Nothing is blocking the built-in camera on the front of each projector.
Note: Auto adjustment is not available for the following lenses: ELPLX01, ELPLR04, ELPLM11,
ELPLM07, ELPLL08, ELPLL07 (Pro L1100U/L1200U/L1300U/L1405U) and ELPLR04, ELPLL08,
ELPLL07 (Pro L1500U/L1505U). After auto adjustment, the movement range for lens shift is reduced.
1. Press the Menubutton.
2. Select the Extendedmenu and...