Epson Projector Emp Tw200h User Manual

29
Using Cinema Color Editor
Adjusting projected images using a computer
ryMake the desired adjustments.
Select the memory area to be used.
The following two types of memory area are 
available, and up to 6 sets of adjustment settings 
can be saved in each. The type of memory area 
that are available will vary depending on the 
Color Adjustment  settings.
Standard
When Color Adjustment has been set with RGB
Advance
When Color Adjustment has been set with 
RGBCMY
Select the memory area to be used for...

30
Problem Solving
Reading the Indicators
The projector is provided with the following two 
indicators which notify you of the operating status of 
the projector.
The following tables show what the indicators mean and 
how to remedy the problems that they indicate.
*If both indicators are switched off, check that the 
power cable is connected correctly and that power is 
being supplied.
When the  (warning) indicator is lit or flashing 
When the   (operation) indicator is lit or flashing 
: Lit      :...

31
Problem Solving
Troubleshooting
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages 
given for each problem.
Problems relating to images
 No images appear
No images appear  See below
Projection does not start, the projection area is 
completely black, the projection area is completely blue, 
etc.Image colours are not right  p.34
The whole image appears purplish or 
greenish, images are black & white, colours 
appear...

32
Problem Solving
 The message Not Suppor ted. is displayed
 The message No Signal. is displayed
Were the projector and 
computer connected while 
their power was already turned 
on?If the connection is made while the power is already turned on, the 
function (Fn) key that switches the computers video signal to external 
output may not work. Turn the power for the computer that is connected 
to the projector off and then back on again.
Is the computer display output 
set to only the computers 
accessory...

33
Problem Solving
Troubleshooting
 Images are fuzzy or out of focus
 Interference or distortion appear in images
 Image is truncated (large) or small
Has the focus been adjusted 
correctly?Adjust the focus. Setup Guide
Is the lens cover still attached?Remove the lens cover.
Is the projector at the correct 
distance?The recommended distance from the projector to the screen is within 
87–1365 cm (2.9–44.8 ft.) for a screen size of 16:9, and 108–1672 cm 
(3.6–54.9 ft.) for a screen size of 4:3. Set up the...

34
Problem Solving
 Image colours are not right
 Images appear dark
Has the Position setting 
been adjusted correctly?Use the Position menu command to make the adjustment.
Setting - Screen - Position p.18
Has the computer been set for 
dual display?If dual display has been activated in the Display Properties of the 
computers Control Panel, the projector will only project about half of 
the image on the computer screen. To display the whole of the image on 
the computer screen, turn off the dual display...

35
Problem Solving
Troubleshooting
 Projection stops automatically
Problems when projection starts
 Power does not turn on
Problems with the remote control
 The remote control does not work
Is sleep mode active?When Sleep Mode has been set to ON, the lamp turns off 
automatically if no signal is input for about 30 minutes, and the 
projector switches to standby mode. Press the   button on the remote 
control or the   button on the projectors control panel to turn the 
projectors power back on. To cancel...

36
Maintenance
This section describes maintenance tasks such as cleaning the projector and replacing consumable parts.
Cleaning
You should clean the projector if it becomes dirty or if the quality of projected images starts to 
deteriorate.
Cleaning the Air Filter
If the airfilter becomes blocked with dust and the message 
The projector is overheating. Clean or replace the air filter 
and lower the room temperature is displayed, clean the air 
filter.
Turn the projector upside-down and use a vacuum...

37
Maintenance
Appendix
Consumable Replacement Periods
Air Filter Replacement Period
If the air filter becomes broken or too dirty to clean
Replace with an optional air filter.
 Appendix: Optional Accessories p.40
Lamp Replacement Period
•The message Replace the lamp. appears on the screen when projection starts.
•The projected images get darker or star t to deteriorate.
•In order to maintain the brightness and quality of the projected images, a lamp 
replacement warning message will be displayed after...

38
Maintenance
Replacing Consumables
Replacing the Air Filter
Replacing the Lamp
Resetting the Lamp Operating Time
Turn off the power, wait 
for the cool-down period 
to finish (takes 
approximately 30 
seconds), then 
disconnect the power 
cable.Remove the air filter 
cover.
Put your finger 
under the latch.
Lift up.
Dispose of used air 
filters properly in 
accordance with 
your local 
regulations.
Remove the lamp cover 
fixing screws.
Securely tighten the 
lamp fixing screws. Insert the new lamp.Turn...