Epson Projector Emp S1 User Manual

							10
EMP-S1 User’s Guide
InstallationInstallation methodSet up the projector so that it is at right angles to a screen.
Projection distance and screen size
The values should be used as a guide for setting the projector.
c
Be sure to read the Safety Instructions / World-Wide Warranty 
Terms guide before installation.
p
When setting up the projector against a wall, leave a space of at 
least 20cm between the projector and the wall.
Projection distance:
87-1109cm
20cm (7.9in.) or more
4:3 Screen size (cm/ft.)
 A cm (ft.)
 B cm (in.)
30 (61 × 46 / 24.0 × 18.1) 87−108 (2.9 − 3.5) 4 (2)
40 (81 × 61 / 31.9 × 24.0) 117−145 (3.8 − 4.8) 6 (2)
60 (120 × 90 / 47.2 × 35.4) 177−219 (5.8 − 7.2) 9 (3)
80 (160 × 120 / 63.0 × 47.2) 237−293 (7.8 − 9.6) 12 (5)
100 (200 × 150 / 78.7 × 59.1) 297−367 (9.7 − 121) 14 (6)
200 (410 × 300 / 161.4 × 118.1) 596−738 (19.6 − 24.2) 29 (11)
300 (610 × 460 / 240.2 × 181.1) 895−1109 (29.4 − 36.4) 43 (17)
90°Centre of 
lens
Screen
Projection distanceDistance from 
centre of lens to 
bottom edge of 
screen 
						

							11
EMP-S1 User’s Guide Before Using the Projector > Installation
Other installation methodsfRear projection
(Using a translucent screen)
fCeiling projectionfCeiling/Rear projection
(Using a translucent screen)
* The optional ceiling mount is required when installing the projector from 
a ceiling. Please contact your dealer if you wish to use this method, as 
special equipment is required for installation. sOptional Accessories 
P.60p
When using rear projection, or projecting from a ceiling, select 
the appropriate mode in the Setting 
→
 Screen 
→
 
Projection configuration menu. sSetting menu P.38 
						

							12
EMP-S1 User’s Guide
Connecting to a ComputerCompatible computersCondition 1: Check that the computer has an image output port, such 
as an RGB port, monitor port or CRT port.
Some computers with an in-built monitor and some laptop 
computers may not be compatible. Please refer to your 
computer manual for further details.
Condition 2: The display frequency and resolution of the computer 
must correspond to that of the projector. sSupported 
Display Resolutions P.66
fLaptop connection
Setup examples
Press and hold the [Fn] key, followed by the appropriate function number 
key.
Refer to your computer’s documentation for further details.
 It may take a few moments until the computer image is projected.
 Depending on your version of Windows, a dialog box may appear to 
alert you that new display hardware has been found. Follow the on-
screen instructions to proceed. If you have any problems, please contact 
the nearest address provided in theInternational Warranty Conditions 
section in the Safety Instructions / World-Wide Warranty Terms guide.
 Depending on the PC, the monitor may go blank when using the external 
video output on the computer.
c
When connecting, be sure to:
• Turn off the power for both the projector and the computer.
Damage may result if you try to make a connection when the 
power is switched on.
 Check the connector types.
Damage may result if you attempt to insert a connector into the 
incorrect port.
p
 You may need to purchase a separate adapter depending on the 
shape of the computers port. Refer to the documentation 
provided with the computer for further details.
 If the computer and projector are too far away from each other 
for the provided computer cable to reach, use the optional 
VGA-HD15 PC cable. sOptional Accessories P.60
p
When using a laptop or a PC with an in-built monitor, select 
external video output on the computer.
NEC
[Fn]+[F3]
Panasonic
To s h i b a [ F n ] + [ F 5 ]
IBM
[Fn]+[F7]
SONY
Fujitsu [Fn]+[F10]
MacintoshAfter start up enable Mirroring in the 
Monitors Control Panel. 
						

							13
EMP-S1 User’s Guide Before Using the Projector > Connecting to a Computer
Projecting images from a computerDifferent cables are used depending on whether the monitor port of 
your computer is a Mini D-Sub 15Pin, 5BNC
g or 13w3 port.
fWhen using a Mini D-Sub 15 pin connector
fWhen using a 5BNC portfWhen using a 13w3 port
To monitor port
To Computer / 
Component Video port Computer cable (accessory)To monitor port
VGA-HD15 / BNC PC cable (optional) To Computer / 
Component Video port
p
 Select Computer in the Image 
→
 Input signal 
configuration menu. sImage menu P.35
 Do not bind the power cable and computer cables together. 
Interference or operational problems may result.
 A particular type of cable may be required for some 
workstations. Please check with the maker of your workstation.
To monitor port
13w3 cable (commerically available)
To Computer / 
Component Video port 
						

							14
EMP-S1 User’s Guide Before Using the Projector > Connecting to a Computer
Playing sound from a computerYou can play sound from a computer through the projectors in-built 
speaker.fVolume adjustment
Press [a] or [b] on the remote control.
You can also adjust the volume from the configuration menu.
[Menu] button → Setting → Volume sSetting menu P.38
Connecting to an external monitorThe image being input into the projector can be displayed on a 
computer monitor.
p
When using computer and video equipment alternately, swap the 
cable or use an audio switch.
To audio out port
stereo mini jack - 2RCA cable 
(commercially available)RCA jack
To Audio port
stereo 
mini jack
p
 Video images cannot be output to an external monitor.
 Setting gauges (for keystone correction, etc.) and  
configuration menus will not be displayed on an external 
monitor.
monitor cable
To Monitor Out port 
						

							15
EMP-S1 User’s Guide Before Using the Projector > Connecting to a Computer
Presentation Remote ControllerYou can use the Presentation Remote Controller as a wireless mouse 
to control the mouse pointer on the computer screen.fCompatible computers
Windows:   Windows 98 / 2000 / Me / XP
(Only compatible with the full versions of Windows. 
Upgraded versions cannot be used.)
Macintosh: Mac OS 9.1 or later
fInstalling the driver (Windows)
Screen contents will differ according to the version of Windows you are 
using. This explanation uses screenshots taken from Windows 98.
Driver installation is not required for the Macintosh.A
Connect the accessory Presentation Remote Receiver 
to the USB port of the computer.The Add New Hardware wizard is displayed.
Under normal circumstances, maintain the default settings and click 
Next to proceed.
B
Click Next.
p
 The Presentation Remote Receiver can only be connected to 
computers with a standard USB interface. 
 Some computer settings may have to be changed in order for 
the mouse function to be used. Refer to your computer’s 
documentation for further details.
Before using the Presentation 
Remote Controller, remove the 
insulation tape.
Infrared receiver
To USB port
Presentation Remote
Receiver (accessory) 
						

							16
EMP-S1 User’s Guide Before Using the Projector > Connecting to a Computer
C
Keeping the defaults, click Next.
D
Click the check box next to Specify a location and 
type C:\WINDOWS. Click Next
E
Click on Next to confirm the message which is 
displayed.
F
Click on Finish.The installation of the driver is complete.
p
 You may need to enter a different location to search for the OS 
files that you are using.
 Click on Browse if you want to change the default search 
location.
p
The driver installation screen is displayed a second time.
(The Presentation Remote Controller driver has two parts; the 
mouse driver and the keyboard driver.) Follow the on screen 
instructions to complete the installation.  
						

							17
EMP-S1 User’s Guide Before Using the Projector > Connecting to a Computer
fPart Names and Functions
Operate the Presentation Remote Controller by aiming it at the Presentation Remote Receiver.
When using the Freeze or A/V Mute functions, aim the presentation remote control towards the remote control infrared receiver of the projector.
fOperating range 
Operable distance: Max. approx. 6m (20ft.) 
(May be shorter depending on conditions.)
Operable angle:      approx. 30° horizontally, 15° vertically
[L Click] buttonActs as a mouse left-click.
[Freeze] button Keeps the current computer or 
video image on the screen.
[Page Up] / [Page Down] buttonsPress these buttons to scroll back and forth 
through pages when projecting a 
PowerPoint presentation.[A/V Mute] buttonMomentarily turns off the audio and video.
remote control infrared transmitterTransmits remote control signals.joystickTo move the mouse pointer, move the 
joystick in any of the following
directions : up, down, left, right, 
diagonally.[R Click] buttonActs as a mouse right-click.
Double click:Push the [L Click] button twice.Drag and drop:To drag, press and hold the [L Click] button and 
move the cursor with the joystick. 
The item will be dropped when [L Click] is released.p
If the mouse button settings have been reversed at the computer, 
the operation of the remote control buttons will also be reversed.
30°
Max 6m 30°
15°
15° 
						

							18
EMP-S1 User’s Guide
Connecting to Video EquipmentProjecting video imagesfFor Composite Video (DVD, VHS, Video games)fFor S-Video (DVD, S-VHS, Video games)
fFor Component Video (DVD, Video games)
c
When connecting, be sure to:
 Turn off the power for both the projector and the video 
equipment.
Damage may result if you try to make a connection when the 
power is switched on.
 Check the connector types.
Damage may result if you attempt to insert a connector into the 
incorrect port.
To video 
out portAV cable (yellow) 
(commercially available)
To Video port
p
After projection starts, change the Input Signal setting in the 
Image menu to either Component Video (YCbCr
g) or 
Component Video (YPbPr
g) to match the signals from the 
video equipment. s P. 3 5
To S-Video out portS-Video cable 
(commercially available)
To S-Video port
From component 
video out portComponent video cable 
(optional)
To Computer/
Component Video port 
						

							19
EMP-S1 User’s Guide Before Using the Projector > Connecting to Video Equipment
fFor RGB Video
Playing sound from video equipmentfVolume adjustment
Press [a] or [b] on the remote control.
You can also adjust the volume with the configuration menu.
[Menu] button → Setting → Volume sSetting menu P.38
p
 After projection starts, change the Input Signal setting in the 
Image menu to Computer. s P.35
 For an RGB connection, a commercially available adapter or 
converter cable may be required.
Computer cable 
(accessory)
To Computer/
Component Video port To RGB out port
p
When using computer and video equipment alternately, swap the 
cable or use an audio switch.
AV cable (red/white)
(commercially available)
To Audio port To audio out port