Epson Projector Emp 7300 User Manual

							Turning the Equipment On and Off
n  n  n  n  n  n
31
Turning the Equipment On and Off
Always turn on the projector and its attached equipment in 
the following order.
1. Video source
2. Audio source (if different than computer or video source)
3. Projector
4. External speaker or PA system
5. Computer
Turning the Projector On and Off
1. Remove the projector lens cap.
2. Press the Power button on the remote control or control 
panel. The green power indicator comes on.
If computer or video equipment is attached, the computer or 
video signal is projected. 
Allow about 30 seconds for full illumination.
¨
Warning: Never look into the lens when the lamp is on. This can 
damage your eyes. It is especially important that children are not 
allowed to look into the lens. 
						

							Using the Projector
  n  n  n  n
32
Reverse the order shown above to turn off the projector and 
other equipment. After you press the Power button to turn 
off the projector, the fan will remain on and the operation 
indicator will flash orange for about one minute as the 
projector cools.
 The indicator stops blinking (and remains lit in orange) when 
the cooling operation is complete.
¨
Note: The projector is designed so that it cannot be turned back 
on while the power indicator is flashing green. Before pressing 
the Power button again, wait until the lamp has cooled and the 
operation indicator is orange.
Sleep Mode
Sleep mode conserves electricity by automatically turning off 
the lamp after the projector has not been used for 30 minutes. 
In sleep mode, the projector’s operation indicator is orange 
and only a minimum amount of the projector’s circuitry 
remains on. This conserves electricity, cools the projector, and 
extends the life of the lamp. When the projector is in sleep 
mode, you can press the Power button to start projecting 
images, or you can unplug the projector’s power cord.
operation indicator 
						

							Focusing and Positioning the Screen Image
n  n  n  n  n  n
33
Focusing and Positioning the Screen 
Image
After an image appears on the screen, check to see if it is in 
focus and whether it fits properly on the screen.
• To adjust the focus of the image, rotate the focus ring, 
which is the outer ring on the projector’s lens. 
• To adjust the size of the image, rotate the inner zoom ring. 
Rotate the zoom ring clockwise to make the image larger, 
and counterclockwise to make it smaller.
zoom ringfocus ring 
						

							Using the Projector
  n  n  n  n
34
If you need to raise or lower the image on the screen, extend 
or retract the two feet at the bottom of the projector as 
follows.
1. Stand behind the projector and support the front of it 
while you lift the foot adjuster lever located above the feet. 
This unlocks the feet so they can move up and down 
freely. Do not let the projector drop.
¨
Caution: Do not hold the projector by the lens as you may 
damage it.
2. While lifting the foot adjuster lever, raise or lower the 
projector until the screen image is positioned correctly.
3. Release the lever to lock the feet in their new position.
4. To fine-tune the height of the projector, turn the feet 
clockwise to raise the height or anti-clockwise to lower it. 
						

							Focusing and Positioning the Screen Image
n  n  n  n  n  n
35
Resize Button 
The Resize button allows you to select the projection screen 
mode for certain types of image input signals from a 
computer.
EMP-7300/7200
With images up to XGA size(1024x768 pixels), you can 
choose from two projection methods. Either display the 
image in the center of the projection area(Window display) or 
display the image full size(Resize display).
You can also choose from two projection methods with 
images greater than XGA size. Either project a portion of the 
image or project the entire image in a compressed format. 
The projector automatically reduces the image size to the 
projectors maximum resolution. The Resize button cannot 
be used with XGA
EMP-5300
With images up to SVGA(800x600 pixels), you can choose 
from two projection methods. Either display the image in the 
center of the projection area(Window display) or display the 
image full size(Resize display).
You can also choose from two projection methods with 
images greater than SVGA size. Either project a portion of the 
image or project the entire image in a compressed format. 
The projector automatically reduces the image size to the 
projectors maximum resolution. The Resize button cannot 
be used with SVGA. 
						

							Using the Projector
  n  n  n  n
36
Controlling the Projector
Normally you control the projector using the remote control. 
The buttons on the remote control allow you to do the 
following:
• Switch power on and off.
• Auto-set-up of the computer image screen.
• Switch between input images (Computer 1, Computer 2, 
video-computer).
• Access menu for adjustment of image, audio, video, and 
display settings.
• Control resizing.
• Control display freeze.
• Control display blanking.
• Adjust and mute audio output.
• Control custom functions.
• Move the pointer. 
						

							Controlling the Projector
n  n  n  n  n  n
37
Using the Remote Control
When using the remote control, always point it towards the 
remote control receivers located at the front and at the back 
of the projector.
To be able to use the remote control as a cordless mouse 
connect the projector to your computer with all cables came 
with the EMP-7300/7200/5300.
To use the remote control, always point it towards the remote 
control receivers located at the front of the projector.
You can use the remote control up to 10 metres (33 feet) 
from the projector.
¨
Note: The projector may not respond to remote control 
commands in these conditions: ambient light is too bright; a 
certain type of fluorescent light is present; a strong light source 
(such as direct sunlight) shines into the infrared receiver; or 
other equipment emitting infrared energy is present (such as a 
radiant room heater). Remove these conditions to use the remote 
control or control the projector from a computer.
Menu
1
24
5
3
- Volume +
Power Source
Effects
ResizeBlank
Custom
Freeze
Mute
bottom
multi-purpose 
button top
multi-purpose 
button pointer button
Remote control 
						

							Using the Projector
  n  n  n  n
38
In addition to the remote control, you can also control the 
projector by using the buttons on the projector’s operation 
panel located on top of the projector.
This table summarizes the functions on the remote control.   
* When the computer 2/5 BNC switch on the back of the projector is turned to 5 
BNC, the source is switch to 5 BNC.
Button Function
Menu Displays or hides the menu.
Source Switches to Computer 1 , Computer 2*, or Video.
Pointer button Use the pointer button to navigate the menus or use 
the remote as a mouse pointer when the projector is 
connected to the computer with all cables came with 
the EMP-7300/7200/5300.
Effects buttons Use to display special effects in conjunction with the 
projector software.
Top multi-pur- 
pose buttonActs as a right mouse click, registers a menu selection, 
and selects other custom functions.
Bottom multi-pur- 
pose buttonActs as a left mouse click, registers a menu selection, 
and selects other custom functions.
Blank Clears the screen of special effects and switches to a 
black, a blue or user logo display.
Resize Switches the display dot mode and resize mode (for 
VGA, SVGA and SXGA input).
Custom Use to assign functions to the Effects keys using the 
projector software.
Freeze Keeps the current computer or video image on the 
screen.
Mute Cuts off audio.
 – Volume + Adjusts the volume.
Power Starts or stops the projector. 
						

							Controlling the Projector
n  n  n  n  n  n
39
Using the Control Panel
You can use the control panel to control the printer instead of 
the remote control. However, you can program and access the 
custom features only when you are using the remote control. 
Power
Blank Source
Resize
Menu
MuteVolume
Sync.
Sync.
TrackingTracking
Enter button
Operation Panel 
						

							Using the Projector
  n  n  n  n
40
The following table summarizes the functions on the control 
panel.   
* When the computer 2/5 BNC switch on the back of the projector is turned to 5 
BNC, the source is switch to 5 BNC.
Button Function
Power Starts or stops projection.
Source Switches to Computer 1 , Computer 2*, or Video.
Menu Displays or hides the menu.
Up, down arrows 
(Sync+/Sync-)Synchronizes the computer’s graphic signal.
Use these buttons to adjust an overall image that is 
fuzzy or streaked, or to select menu items during 
menu opera tions.
Left, right 
arrows(tracking-/ 
tracking+)Matches the projector’s internal clock to various 
computer graphic signals (tracking adjustment).
Use these buttons to adjust an image with vertical 
fuzzy lines, or to change numeric settings during menu 
opera tions.
Enter key Registers a menu selection.
Resize Switches the display dot mode and resize mode (for 
VGA, SVGA, and SXGA input).
Mute Cuts off audio.
 – Volume + Adjusts the volume.