Home > Epson > Projector > Epson Projector Emp 703 User Manual

Epson Projector Emp 703 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Epson Projector Emp 703 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1734 Epson manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							Setting Up the Projector
    n  n  n  n  n  n
    5
    5. To insert the batteries in the remote control device, slide 
    off the battery compartment cover.
    6. Insert the two AA batteries included with the projector. 
    Make sure the polarity of the batteries is correct.
    7. Replace the battery compartment cover.
    When replacing batteries, take the following precautions:
    • Do not recharge the used batteries or expose to fire or 
    water.
    • Replace batteries as soon as they run out. If the batteries 
    leak, wipe away battery fluid with a soft cloth. If fluid gets 
    on your hands, wash them immediately.
    • Remove the batteries if you will not be using the projector 
    for a long period of time. 
    						
    							  n  n  n  n
    6
    Connecting to a Computer
    You can connect the projector to a computer capable of VGA, 
    SVGA, XGA, SXGA and UXGA output.
    To connect the computer and mouse cables (to use the 
    wireless remote as a mousepointer), see the section in this 
    chapter that applies to your computer.
    The illustration below identifies all the interface ports on the 
    back of the projector; you may want to refer to this as you 
    connect your computer or other equipment to the projector.
    Computer AudioIn Out
    Mouse/Com S-Video
    AudioR
    L
    Video
    Audio Out
    Mouse/Com Audio In
    Computer
    USB Mouse
    Power  Inlet S-Video
    VideoL-Audio-R 
    						
    							Connecting to a Computer
    n  n  n  n  n  n
    7
    Connecting to a PC Desktop Computer 
    To connect the projector to your PC desktop computer, you 
    need to:
    • Connect the computer cable
    • Connect the audio cable (if you’ll be projecting with audio)
    Follow the steps in each section for the cables you need to 
    connect. Before beginning, turn off the projector and 
    computer if they are on.
    ¨
    Note: Computer configurations vary. See your computer 
    manual for the location of the ports needed to connect your 
    projector.
    Connecting the Computer
    Refer to this illustration while following the steps below.
    Computer port
    computer cable 
    						
    							  n  n  n  n
    8
    1. If you will be viewing the video on your computer 
    monitor as well as the projector screen, disconnect the 
    monitor cable from the video port on the back of your 
    computer.
    2. Connect one end of the computer cable to the projector’s 
    Computer port. 
    3. Connect the other end of the computer cable to the 
    computer’s video port.
    4. Tighten the screws on all connectors.
    Connecting the Mouse Cables
    If you want to use the remote control as a mouse, you need to 
    connect the PS/2 mouse cable or USB mouse cable.
    Refer to this illustration while following the steps below. 
    Mouse/Com port
    USB mouse cable USB mouse port
    PS/2 mouse cable 
    						
    							Connecting to a Computer
    n  n  n  n  n  n
    9
    1. Connect the 9-pin end of the PS/2 mouse cable or, the 
    USB mouse cable to the Mouse/Com or USB mouse port 
    on the projector.
    2. Disconnect your mouse from the mouse port on the back 
    of your computer and replace it with the other end of the 
    PS/2 mouse cable or USB mouse cable. (Your computer’s 
    mouse will be disabled while you are using the remote 
    control as a mouse.)
    Connecting the Audio Cable
    1. If you will be using audio, connect one end of the audio 
    cable to the Audio In jack on the projector.   
    2. Connect the other end of the audio cable to the speaker or 
    audio out port on the computer’s sound card. 
    Audio* 
    n jack
    audio cable 
    						
    							 
      n  n  n  n 
    10  Connecting to a PC Laptop Computer   To connect the projector to your PC laptop computer, you 
    need to:
    • Connect the computer cable
    • Connect the mouse cable (if you want to use the remote 
    control as a mouse)
    • Connect the audio cable (if you’ll be projecting with audio)
    Follow the steps in each section for the cables you need to 
    connect. Before beginning, turn off the projector and 
    computer if they are on.
      ¨  Note:   Laptop configurations vary. See your computer manual 
    for the location of the ports needed to connect your projector.  Connecting the Computer Cable  First connect the projector’s computer cable to your laptop. 
    1. Connect one end of the computer cable to the projector’s 
    Computer port.
    2. Connect the other end of the computer cable to the 
    laptop’s video (monitor) port.
    3. Tighten the screws on all connectors.  Computer port
    computer cable 
    						
    							 
    Connecting to a Computer 
    n  n  n  n  n  
    n
     
    11  Connecting the Mouse Cables  If you want to use the remote control as a mouse, you need to 
    connect the PS/2 mouse cable or USB mouse cable.
    Refer to this illustration while following the steps below.
    1. Connect the 9-pin end of the PS/2 mouse cable or USB 
    mouse cable to the Mouse/Com or USB Mouse port on 
    the projector.
    2. Connect the 6-pin (mini-DIN) end of the PS/2 mouse 
    cable or USB mouse cable to the external mouse port or 
    USB port on your laptop.
    3. Configure your laptop to work with an external mouse.
    Mouse/Com port
    PS/2 mouse cable
    USB mouse cable 
    						
    							 
      n  n  n  n 
    12  ¨  Note:   You may have to set the display to appear on both the 
    laptop’s screen and the projector. Some laptops let you change this 
    setting with the keyboard’s function keys or by using a setup 
    utility provided by the computer manufacturer. Check your 
    laptop’s manual or online help for instructions.  Connecting the Audio Cable  1. If you will be using audio, connect one end of the audio 
    cable to the Audio In jack on the projector.   
    2. Connect the other end of the audio cable to your laptop. 
    Audio In jack
    audio cable 
    						
    							 
    Connecting to a Computer 
    n  n  n  n  n  
    n
     
    13  Connecting to a Desktop Macintosh   To connect the projector to your desktop Macintosh, you 
    need to:
    • Connect the computer cable
    • Connect the mouse cable (if you want to use the remote 
    control as a mouse)
    • Connect the audio cable (if you’ll be projecting with audio)
    Follow the steps in each section for the cables you need to 
    connect. Before beginning, turn off the projector and 
    computer if they are on.
      ¨  Note:   Macintosh configurations vary. See your computer 
    manual for the location of the ports needed to connect your 
    projector.  Connecting the Computer Cable  First connect the computer cable. Refer to this illustration as 
    you follow the steps below.  
    Macintosh desktop 
    adapter Computer port
    computer cable 
    						
    							 
      n  n  n  n 
    14  1. Connect one end of the computer cable to the projector’s 
    Computer port.
    2. Remove the small cover on the Macintosh desktop adapter 
    and set its DIP switches in accordance with the resolution 
    you want to use (such as 16-inch mode). See your 
    Macintosh documentation for instructions. 
    						
    All Epson manuals Comments (0)

    Related Manuals for Epson Projector Emp 703 User Manual