Epson Projector Emp 7000 Specifications

							1/5/99
ESC / VP Reference ManualLevel 3
Page 71
Gamma Data ( Group  :  8   Item  :  3 )
Sets gamma data directly from outside.
    [Function]      Sets gamma data and sends 33 gradation data for each RGB.
  [Form]       1B  28  01  08  03  Parameter  CS
  [Parameter]
This parameter specifies RGB type and sets gamma data.
    R G B  Type  :  1 byte         ( R : 00   G : 01   B : 02 )
    Gamma Data  :     33 byte       ( No correction  0 to 32 )



 
Get Gamma Data
    [Function]      Gets the gamma value (33 gradation) presently set.
  [Form]       1B  07  02  08  03  Parameter  CS
  [Parameter]
This parameter specifies RGB type and sets gamma data.
        R G B    Type    :  1 byte   ( R : 00    G : 01    B : 02 )
  [Return Value]
Returns gamma data (33 gradation)    for specified type. ( 33 byte )

 	

 

  
 
	

&  !(.)$ 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 72
CPU A / D Register ( Group  :  8   Item  :  4 )
Get CPU A / D Register
    [Function]      Gets values of CPU A / D register data.
  [Form]       1B  07  02  08  04  Parameter  CS
  [Parameter]
This param eter specifies A / D register.
L C P 1
A / D Register :   ( 0 to 1 ) 1 byte
L C P 2
A / D Register :   ( 0 to 2 ) 1 byte
Detecting Temp ( L V side)   : 0
Detecting Temp (Lamp side)   : 1
Detecting Temp (P B S side)   : 2
  [Return Value]
Returns register data specified by A / D.
Range of Return Value :       00 to FF

	



  
 
	


 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 73
Key Codes ( Group  :  8   Item  :  5 )
Get Key Codes
    [Function]      Gets key codes of keys.
  [Form]       1B  06  02  08  05  EB
  [Return Value]
Returns key codes have been pressed so far. Each key is represented by 1 bit, so if more than
two keys are pressed at same time, it returns the sum of them.
Key Codes :      ( 5 byte )
S t a n d b y  :      0000000001 S y n c + :      0000008000
C o m p u t e r  :      0000000002 S y n c - :      0000010000
V i d e o  :      0000000004 T r a c k i n g + :      0000020000
R e si z e  :      0000000008 T r a c k i n g - :      0000040000
F r e e z e  :      0000000010 M e n u  :      0000080000
B l a n k  :      0000000020 S e l e c t + :      0000100000
A u t o  :      0000000040 S e l e c t - :      0000200000
M u t e  :      0000000080 A d j r s t    + :      0000400000
E n t e r  :      0000000100 S e l e c t - :      0000800000
P o w e r  :   0000000200 U p :   0001000000
S o u r c e  :      0000000400 D o w n  :      0002000000
P a u s e  :      0000000800 L e f t  :      0004000000
U s e r  :      0000001000 R i g h t  :      0008000000
V o l u m e  + :   0000002000 Mouse Left Button :   0010000000
V o l u m e - :      0000004000 Mouse Right Button :      0020000000
Custom :   0040000000

	 
	
 	 
  	



 
	 	 
	
 
	
 
 

 
 
 

 
   

 
 

 
 



	

!

  
 
	



/! 0! 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 74
F R O M  Checksum ( Group  :  8   Item  :  6 )
Making F R O M    Checksum
  [Function]   Makes checksum of FROM presently contained.
  [Form]       1B  06  01  08  06  CS
  [Parameter]     Non




 	
 (Note) Making the checksum takes 6 seconds. No commands are accepted during it.
Get F R O M    Checksum
  [Function]   Gets the checksum of FROM.
  [Form]       1B  06  02  08  06  CS
  [Return Value]
Returns the checksum of F R O M.


*	

%

  
 
	

!( /! 0! 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 75
Mouse Movement ( Group  :  8   Item  :  7 )
Mouse Movement Setting
    [Function]      Permits or inhibits mouse movements.
  [Form]       1B  07  01  08  07  Parameter  CS
  [Parameter]
This parameter specifies the data to Permit or Inhibit.
    Possible Data for Setting :
Inhibit    :  00
Permit    :  01


	
Get State of Mouse Movement
    [Function]      Gets the state of mouse movement.
  [Form]       1B  06  02  08  07  E9
  [Return Value]
Returns the state of mouse movement.


*	



  
 
	
 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 76
O S D Parameter ( Group  :  8   Item  :  8 )
O S D Parameter Setting
    [Function]      Sets parameters of OSD display. (W hen displaying OSD, first you need to preset the
              following settings related to the OSD display.)
  [Form]       1B  Size  01  08  08  Parameter  CS
  [Parameter]
  ( For  EMP/ELP-3500 )
This parameter sets the start coordinate for OSD display, line width, letter size, backcolor and
flashing cycle.
Start X-coordinate      : Register value at the horizontal start position
            of Display RAM on the OSD screen ( 2 byte )
Start Y -coordinate      : Register value at the vertical start position
            of Display RAM on the OSD screen ( 2 byte )
Magnification          :    1 byte
V magnification 1 / H magnification 1 = 0    V magnification 1 / H magnification 2 = 1
V magnification 2 / H magnification 1 = 2    V magnification 2 / H magnification 2 = 3
BackColor       :   1 byte
BLACK = 0 YELLOW = 3 CYAN = 6
RED= 1BLUE= 4WHITE= 7
GREEN = 2 MAGENTA = 5
BackColor of Inverted Characters       :   1 byte
BLACK = 0 YELLOW = 3 CYAN = 6
RED= 1BLUE= 4WHITE= 7
GREEN = 2 MAGENTA = 5
Flashing Cycle     :   1 byte
No flash =    0 Flashing Duty Rate23 %    =    1
Flashing Duty Rate 50 % =    2 Flashing Duty Rate 75 %    =    3
All Luster Blanking      :      1 byte (Display BackColor / Non-display)
O N =  1
O F F =    0
Display Mode   :   1 byte (Set 1)
Lines of Inverted Characters      :      1 byte
Specifies lines for inverted characters from the first line to eighth line in the values
from 0 bit to 7 bit. Sets 1 for the byte of inverted characters line.
  !

	
	
#
$


	







	
%# &# %# &# 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 77
 ( For EMP/ELP-5000, 5100, 7000, 7100 )
The parameters sets the start coordinate for OSD display, line width, letter size,
backcolor and flashing cycle.
Start X-coordinate      :  Start X-coordinate on the OSD screen
 (Pixel Unit 60 to 775)    2 byte
Start Y-coordinate      : Start Y-coordinate on the OSD screen
 (Pixel Unit 0 to 581)    2 byte
Height of Characters : Height of Characters (Pixel unit    18 to 63)    1 byte
OSD Backcolor :   1 byte
BLACK = 0 CYAN = 3 YELLOW = 6
BLUE = 1 RED = 4 W HITE = 7
GREEN = 2 MAGENTA = 5 No backcolor = 8
Flashing Cycle     :   1 byte
No flash      :   0 1 / 1 Flash   :   1
1 / 1 Flash   :   2 3 / 1 Flash   :   3
     

	
	
	#$%
&%  !   !  
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 78
O S D  Character Data ( Group  :  8   Item  :  B )
O S D    Character Data Setting
    [Function]      Sets characters to display OSD. (If displaying OSD, you first need to preset for OSD
          display in the OSD parameter settings.)
  [Form]       1B  Size  01  08  0B  Parameter  CS
  [Parameter]
  (For EMP/ELP-3500)
This parameter sets the display position on the OSD screen and number of characters in
order of displaying character parameters and character codes repeatedly.
Display position on the OSD screen      :      2 byte
    [X-position : 1 byte]
Specify the start position to display with character’s
coordinates.    Range : 0 to 23
    [Y- position : 1 byte]
Specify the start position to display with character’s
coordinates.    Range : 0 to 9
Character parameters   :   1 byte
    [Color of Character : 4 bit]
B L A C K   :   0 B L U E       :   4
R E D       :   1 M A G E N T A :   5
G R E E N   :   2 C Y A N       :   6
Y E L L O W  :  3 W H I T E     :   7
    [Flash / No Flash : 1 bit]
Flash   :   1
No Flash   :   0
    [Invert / No Invert : 1 bit]
Invert   :   1
No Invert   :   0

 



	 
	
!   
Character Code (MITSUBISHI    M35042-XXXSP : Character font code)    : 1 byte

 	




	

		

	


		

	

			

	


	
	

		
	


	 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 79
    ( For EMP/ELP-5000, 5100, 7000, 7100 )
The parameter sets the display position on the OSD screen and number of characters in
order of displaying character parameters and character codes repeatedly.
  Parameter :
Display position on the OSD screen    :   2 byte
    [X-position : 1 byte]
Specify the start position to display with character’s
coordinates.    Range : 0 to 32
    [Y-position : 1 byte]
Specify the start position to display with character’s
coordinates.    Range : 0 to 13
Character Parameters   :   1 byte
    [Color of Character : 3 bit]
B L A C K   :   0 R E D          :   4
B L U E     :   1 M A G E N T A  :   5
G R E E N   :   2 Y E L L O W    :   6
C Y A N     :   3 W H I T E      :   7
    [Flash / No Flash : 1 bit]
Flash      :   1
No Flash   :  0
    [BackColor of Character : 4 bit]
B L A C K   :   0 R E D          :   4
B L U E     :   1 M A G E N T A  :   5
G R E E N   :   2 Y E L L O W    :   6
C Y A N     :   3 W H I T E      :   7
No BackColor :      8

 


	
	

!   
Character Code ( THOMSON STV942X : Character Font Code )    : 1 byte

 	




	

		

	


		

	

			

	


	
	

		
	


	 
						

							1/5/99
ESC / VP Reference ManualLevel 3
Page 80
No Gamma ( Group  :  8   Item  :  C )
No Gamma Setting
    [Function]      Controls digital gamma correction.
  [Form]       1B  07  01  08  0C  Parameter  CS
  [Parameter]
    Possible Data for Setting :
No   :  00
Yes    :  01 (only EMP/ELP-5000, 5100, 7000 and 7100 are available)