Epson Projector Emp 5600 User Manual

							 Menu Operations - 69
Effect Bar Sets the color, direction and width of the bar allocated to the 
[4] button on the remote control unit.
Press the [Enter] button and select the required item from the 
bar setup menu. The color, direction and width can be 
selected independently for each of the settings between 1 
and 3.
·The [4] button executes the bar function. The bar types will 
be switched between 1 and 3 sequentially for each time the 
[4] button is pressed. (see page 60
)Individual
settings 
between types 1 
to 3
Cursor Speed Selects the speed of Cursor.
L: Slow M:Medium H:FastM
Reset Returns all effect menu adjustment values to the default val-
ues.
Press the [Enter] button and then select [Yes] on the confir-
mation screen displayed.
·Select [Reset All] to return all image and sound values to 
the default settings. (see page 71
)-
Set-
tingKeystone Adjusts images which appear trapezoidal.
·The screen will be reduced in size when keystone correction 
has been performed.
·The status of the keystone correction will be recorded. 
Perform readjustments that match the installation position 
when the projector position or angle have been changed.
·Reduce the sharpness if blurring occurs after keystone 
correction. (see page 67
)Center value (0)
P in P Sets the input source for the P in P function’s sub-screen.
·The P in P function is executed by pressing the [PinP] 
button on the remote control unit. (see page 61
)Composite
No Signal Msg The status for [No Image Signal Input] and other message 
display.
·The user logo must be registered and set up before it can be 
amended.Blue
Prompt Sets whether to display the input source on the screen or not. ON
A/V Mute Sets up the screen status for when the [A/V Mute] button is 
pressed.
·User logos must be registered and set up before they can be 
amended. Black
Computer2 Sets the mode for the input image signals connected to the 
Computer2/Component Video port.
RGB : Set when the input is a RGB signal.
YCbCr : Set when the input is a component video signal 
(YCbCr).
YPbCr :  Set when the input is a component video signal 
(YPbCr).RGB
To p  
MenuSub MenuFunctionDefault Value 
						

							70 - Menu Operations
Set-
tingSleep Mode Sets the energy-saving function for when no image signals 
are being input. When this is set at [ON], projection will be 
automatically ended and the projector will enter the sleep 
mode if no image signals are input and no operations are 
performed for a period of thirty minutes (the operation indi-
cator will be illuminated in orange).
Press the [Power] button to restart projection.ON
Reset Returns all setting menu adjustment values to the default 
values.
Press the [Enter] button and then select [Yes] on the confir-
mation screen displayed.
·Select [Reset All] to return all image and sound values to 
the default settings. (see page 71
)-
User’s 
LogoExecute Registers user logos. (see page 72
)
Press the [Enter] button and follow the instructions dis-
played on the confirmation screen.
·The saving procedure requires a certain amount of time to 
complete. Do not attempt to operate the projector or the 
equipment connected to the projector while this procedure 
is running. Failure to observe this may result in damage.
·The size that can be registered is 400 x 300 dots.
·The display size will be adjusted when video images are 
being projected.EPSON’S logos
Adva
ncedLanguage Sets the language with which messages are to be displayed.
Press the [Enter] button and select the required language 
from the language selection menu displayed.English
Startup Screen Displays the user logo during warm-up after the power has 
been switched on.
·The user logo must be registered and set up before it can be 
amended.ON
Color Setting Adjusts the color temperature of the image.
Absolute color temperature: Sets the color temperature.
RGB: Sets the strength of the RGB colors (red, green and 
blue.)
Press the [Enter] key to display the color setup menu, select 
the R, G and B items, and then set the required value. 
·Set the color temperature value to the yardstick value.Absolute color 
temperature 
7500K
To p  
MenuSub MenuFunctionDefault Value 
						

							 Menu Operations - 71
· The image menu and information displayed will differ in accordance with the projected input 
source, and Menus other than that belonging to the projected input source cannot be adjusted.
·The information menu displays the status of the input source settings being projected.
Adva
ncedRear Proj. Set at [ON] to project images onto a half-transparent screen 
from the rear. The projected image will be inverted.OFF
Ceiling Set at [ON] to project images when suspended from the ceil-
ing. The projected image can be be inverted from left to right 
and up and down.
·The optional ceiling suspension unit is required to suspend 
the projector from the ceiling. (see page 90
)OFF
Reset Returns all advanced setting menu adjustment values to the 
default values.
Press the [Enter] button and then select [Yes] on the confir-
mation screen displayed.
·Select [Reset All] to return all image and sound values to 
the default settings.-
Infor-
mat-
ion(Displays the current settings) -
Reset 
allExecute Returns all items in the set-up menus to the default values.
Press the [Enter] button and then select [Yes] on the confir-
mation screen displayed.
·Execute the [Reset] function from each individual sub menu 
to return the image and sound settings to the default values 
for each menu.
·The user logo, lamp time, language and BNC settings will 
not be returned to the default values. Perform the reset 
procedure after the lamp has been replaced. (see page 87
)-
To p  
MenuSub MenuFunctionDefault Value 
						

							72 - Menu Operations
User logo registration
Registers the images currently displayed as the user logo.
1Displays the image that is to be registered as the user logo.
2Press the [Menu] button and select [User ’s Logo] - [Execute].
The confirmation screen will be displayed.
3Select [Yes] and then press the [  (Enter)] button on the main unit (the [Enter] button 
on the remote control).
The image to be registered will be displayed.
4Adjust the position of the image with the [Sync +/-] and [Tracking +/-] buttons on the 
main unit ([Enter] button on the remote control), and then press the [ Enter] button on 
the main unit (the [Enter] button on the remote control).
The confirmation screen will be displayed.
Video
Audio
Effect
Setting
Users Logo
Advanced
About
Reset All
:Execute:Return
Execute
Users Logo Capture
Do you use the present image
as a users logo?
Ye sNo
:Select :Return :Execute
:Move
/ :Return :Enter 
						

							 Menu Operations - 73
5Select [Yes] and then press the [ (Enter)] button on the main unit (the [Enter] button 
on the remote control).
The enlargement setup screen will be displayed.
6Select the enlargement rate and then press the [ (Enter)] button on the main unit (the 
[Enter] button on the remote control).
The screen to confirm saving will be displayed.
7Select [Yes] and then press the [ (Enter)] button on the main unit (the [Enter] button 
on the remote control).
The image will be saved. Wait until the [saving completed] screen is displayed.
Point
·A certain amount of time is required for the saving process. Do not operate the projector 
or connected equipment while saving is in progress. Failure to observe this may result in 
defects.
·The image size that can be registered is 400 x 300 dots.
·The display size will be amended depending on the input resolution.
Users Logo Capture
Do you use this image?
Ye sNo
:Select :Return :Execute
Users Logo Capture
Set the zoom rate.
zoom rate : 
:Select :Return :Execute
100200300
Users Logo Capture
Do you save the users logo?
If you save it,
the previous users logo
will be overwritten.Ye sNo
:Select :Return :Execute 
						

							74 - Troubleshooting
Troubleshooting
This section provides explanations on potential problems and the methods of taking care of them.




 
Troubleshooting
When you think you have a problem, first of all check the Indicators on the projector.
The projector is fitted with Operation Indicator, Lamp Indicator and Temperature Indicator to 
advise the projector’s status.
Operation Indicator
Indicator StatusCauseRecovery or StatusReference 
Page
Illuminated in 
OrangeStand-by status (Not an error)
Projection will be started when the [Power] 
button is pressed.42
Blinking in Orange Cool-down proce-
dure in progress(Not an error)
·Wait for a moment. The acount of time for the 
projector to cool down (cooling the lamp) will 
depend on the external temperature, etc.
·The [Power] button cannot be used during 
the cool-down period. This will be 
illuminated in orange once the cool-down 
process has been completed, so press the 
button once more then.49
Illuminated in Green Projection in 
progress(Not an error) 42
Computer
A/V mute
Resize PowerOperation Indicator
Lamp Indicator
Temperature Indicator 
						

							 Troubleshooting - 75
Lamp Indicator
Blinking in Green Warm-up in 
progress(Not an error)
·Wait for a moment.
·The green lamp will stop blinking and 
become illuminated once the warm-up 
procedure has been completed.42
Illuminated  in  Red Internal  error Cease operations, remove the Power Plug from 
the socket and contact your dealer or nearest 
address provided at page 97  and request 
repairs.
Extinguished The power is not 
switched onThe power is not switched on.
·Check the power cord connection.
·Check the power supply to the socket.42
Indicator StatusCauseRecovery and StatusReference 
Page
Blinking in Red Lamp error·Replace with a new lamp (ELPLP12).
·If the lamp is broken, take care to avoid injury 
and contact your nearest address provided at 
page 97 Center to request repairs.
·Ensure that the lamp and lamp cover have 
been attached firmly after replacing the lamp. 
The equipment is fitted with a mechanism 
that prevents the lamp from being switched 
on if the lamp and lamp cover are not 
securely in place.87
Blinking in Orange Time to replace the 
lamp.Replace with a new lamp (ELPLP12). 87
Extinguished (Not an error)
The power has not been switched on or nor-
mal projection is in progress.
Indicator StatusCauseRecovery or StatusReference 
Page 
						

							76 - Troubleshooting
Temperature Indicator
Point
·Refer to the section on [When the Indicators Provide No Help] on the following page if the 
Indicators appear normal but the projected image is defective.
·Contact your dealer if an Indicator status not covered by the above table is apparent.
Indicator StatusCauseRecovery and StatusReference 
Page
Illuminated in Red Excesive internal 
temperature
(overheating)·Use the projector within the permissible 
temperature range of between 5 degrees 
Celsius and 40 degrees Celsius.
·Install the projector in a well-ventilated place 
and ensure that the ventilation inlet and 
outlet are not blocked.23
·Clean the Air Filter. 85
Blinking in Red Internal error Cease operations, remove the Power Plug 
from the socket and contact your dealer or 
nearest address provided at page 97 and 
request repairs.
Blinks in orange High-temperature 
cooling in progress·(This is not an error, but the projector will 
automatically cease operating if the 
temperature increases any further.)
·Use the projector within the permissible 
temperature range of between 5 degrees 
Celsius and 40 degrees Celsius.
·Install the projector in a well-ventilated place 
and ensure that the ventilation inlet and 
outlet are not blocked.23
·Clean the Air Filter. 85
Extinguished (Not an error)
The power has not been switched on or nor-
mal projection is in progress. 
						

							 When the Indicators provide No Help - 77




 
When the Indicators provide No Help
Refer to each relevant item if the following situations arise but the indicators provide no help.
·The image is not projected page 77
·No sound page 82
·The image is unclear page 79
·The remote control will not work page 83
·The image is cut up (Large)/Small page 81
·Cannot end page 83
·The image color is bad page 81
·The image is dark page 82
The image is not projected
 Nothing is displayed
Nothing is displayed
Is the Lens Cover still in place?
see page 41
Has the power been switched off and then on immediately?
The [Power] button will not operate after projection has been 
finished (during the cooling down procedure). The [Power] button 
will work again after the cooling down process Projection lamp 
cooling operations: the operation indicator is illuminated in orange 
has been completed.
see page 49
Is the Sleep Mode set at ON?
When the sleep mode has been set at [ON], the lamp will be 
automatically extinguished if no operations occur and no signals are 
input for a period of thirty minutes.
see page 70
Did you press the [Power] button?
see page 42
Has the brightness of the image been correctly adjusted?
see page 67
Is the system in the [A/V Mute] mode?
see page 55
Perform the reset procedure.
see page 71
Is the input image completely black? 
There are cases where input images will become completely black 
owing to screen savers, etc.
Are image signals being input?
No message will be displayed if the [Menu] - [Settings] - [No Signal 
Display] parameter is set at OFF. Set this to black or blue to display 
the message.
Refer to the relevant items when the message is displayed.
see page 78 
						

							78 - When the Indicators provide No Help Messages
[Not Supported] 
will be displayed
[No Signal]
will be displayed
Is the resolution of the image signals being output from the 
computer higher than the displayable resolution (ELP-7600: 1600 x 
1200, ELP-5600: 1440 x 1080)?
see page 26
Check to ensure that the mode supports the frequency of the image 
signals output from the computer.
Refer to the computer’s instruction manual to discover how to amend 
the resolution and frequency of the image signals output from the 
computer.
see page 26
Have the cables been connected correctly?
see page 26, 37
Has the correct image input port been selected for the connection?
Press the [Computer] or [Video] buttons on the projector ([Comp1], 
[Comp2/YCbCr] [Video] on the remote control) to switch the image.
see page 43
Has the power supply to the connected computer or video 
equipment been switched on?
see page 44
Are image signals being output from the connected computer or 
video equipment?
Note-type and liquid crystal type computers must output image 
signals to the projector.
Image signals are not output externally simply because they are 
output to the LCD screen under normal conditions, so the setting 
must be switched to external output.
There are models for which image signals are not output to the LCD 
screen when output externally.
see page 26