Epson Projector Emp 5600 User Manual

							 Connecting the video equipment - 39
In the case of the digital tuners D output port
·Connect the digital tuner to the projectors Computer2/Component Video port with the 
optional D port cable (ELPKC22).
·Connect the L-Audio2-R ports with the RCA audio cable supplied (red/white) to output 
sound from the projectors speakers.
Point
·Set the Computer2 parameter on the menu to [YCbCr] or [YPbPr], as appropriate for the 
input signal being used, when the connection has been established. (see page 69
)
·Establishing connections with digital tuners is only possible in Japan.
·Supports digital tuners up to the D4 rating.
Computer2/Component Video Port
The D port cable
(optional)
for component images
To the audio output 
port L (white)
To the audio output 
port R (red)To the D output port
Audio Port R (Red) Audio Port L (White)
RCA Audio Cable (supplied with the projector) 
						

							40 - Connecting the video equipment
In the case of RGB image signals
·Connect the projectors Computer2/Component Video port to the video equipment with the 
component image cable (available on the open market).
·Connect the L-Audio2-R ports with the RCA audio cable supplied (red/white) to output 
sound from the projectors speakers.
Point
·Purchase the RGB image cable to match the connectors on your equipment.
·Set the Computer2 parameter on the menu to [RGB] when the connection has been 
established. (see page 69
)
Audio Port L (White)
Audio Port R (Red)
To  t h e  R  o u t p u t  p o r t
To the G output port
To the B output port
RCA Audio Cable  (supplied with the projector)For RBG images Cable 
(available on the open 
market)
To the audio output 
port L (white)
To the audio output 
port R (red)
Computer2/Component Video Port 
						

							 Projection - 41
Projecting
This section provides explanations on starting and ending projection, and on the basic func-tions for adjusting projected images.




 
Projection
Images can be projected after all connections have been completed.
Preparations
1Connect the projector to a computer and video equipment. (see page 26, 37)
2Remove the Lens Cover.
3Attach the supplied Power Cord to the projector.
Check to confirm the shape of the projector’s Power Inlet and Power Connector, align the 
connector in the correct direction, and then insert it as far as it will go.
Wa r n i n g
·Never look directly into the lens once the power supply has been switched on. Failure to 
observe this may result in the powerful light damaging eyesight.
·Ensure that the Power Cord supplied is used. The use of cables other than the one supplied 
may result in the outbreak of fire or electric shocks.
Caution
Do not perform any projection tasks with the Lens Cover attached. Failure to observe this may 
result in the cover becoming malformed due to heat.
Power Inlet
Power Connector Power Cord 
						

							42 - Projection
4Plug the Power Plug into the power socket.
The Operation Indicator will be illuminated in orange.
Commencing projection
1Press the [Power] button to turn on the power supply.
The Operation Indicator will begin to blink in green, and projection will be started.
The Operation Indicator will change from blinking to being steadily illuminated in green 
after a while.
Point
Button operations are not possible when the Operation Indicator is blinking in green.
Computer
A/V mute
Resize Power
Illuminated in orange Operation Indicator
Power
Freeze
A/V MuteE-ZoomR/C ON
OFF3
1524
Enter
Esc
PowerVideo Computer
A/V mute
ResizeEsc Help
Menu
Tracking TrackingSync
Sync
Shift
Keystone
Volume Power
Power
Set the R/C ON OFF switch to [ON] first of all 
when using the remote control unit 
Computer
A/V mute
Resize Power
A message stating (No image 
signals input) will be dis-
played when no image sig-
nals have been input. 
(Depending on the no-signal 
setting, this message may not 
be displayed.) (see page 69
) Operation Indicator
Blinking in green → Illuminated 
						

							 Projection - 43
2Select the Port to which the connection has been made when more than one item of
 equipment has been connected.
Press the port button connected to the computer or video equipment to switch the input 
source.
Point
·Even if there is a physical connection, the system will automatically switch to the state 
used immediately before power-off if there is no input signal, or if the connected equip-
ment is not outputting a signal. 
·The Computer #2/Component Video port sources that are switched with the [Computer] 
and [Video] keys on the projector and the [Comp2/YCbCr] key on the remote control will 
only display either the Computer2 (RGB) Computer2 (YCbCr) or the Computer2 (YCbCr) 
depending on the Computer2 setting.
 (see page 69)
Connected
PortButton to SelectDisplay at the top 
right-hand corner of 
the screen
Main UnitRemote Control 
Computer #1 Port [Computer]
(will change whenever 
pressed)[Comp1] Computer1
Computer2/
Component Video (RGB)Computer2 (RGB)
Computer2/
Component Video (YCbCr)[Video]
(will change whenever 
pressed)[Comp2/ YCbCr] Computer2 (YCbCr)
Computer2/
Component Video (YPbPr)Computer2 (YPbPr)
Vi d e o  P o r t [ Vi d e o ]
(will change whenever 
pressed)Vi d e o
S-Video PortS-Video
Comp1
EscMenu
Comp1
P in P PresetVideo
Comp2/YCbCr
Help
- Volume +
Comp2/YCbCr
Video
AutoResize
Video Computer
A/V mute
ResizeEsc Help
Menu
Tracking TrackingSync
Sync
Shift
Keystone
Volume Power
Computer
Video 
						

							44 - Projection
3Starting projection.
Switch on the power supply to the computer or video equipment. If the equipment con-
nected is video equipment, then also press the [Playback] or [Play] buttons.
The [No Signal] display will be erased, and projection will commence.
Point
·If [No Signal] remains displayed, check the connections once again.
·Depending on the computer, there are cases when it is necessary to switch the image sig-
nal output destination with the key ( , etc.) or the settings after establishing the connec-
tion.
The table shown above provides examples for certain products. Refer to the computer’s 
instruction manual for further details.
·Press the [Resize] button when signals that support DVD players or wide television 
screens (16:9 images) have been input. The parameters will change between 4:3 images 
and 16:9 images whenever the switch is pressed.
·There are cases where a projected image will remain projected if a still image is projected 
for a long period of time.
NECPanasonicTo s h i b aIBMSONYFUJITSUMacintosh
Fn+F3 Fn+F3 Fn+F5 Fn+F7 Fn+F7 Fn+F10 Mirroring is set up with Control 
Panel - Monitor adjustments after 
restarting the system. 
						

							 Ending - 45




 
Ending
End through the following procedure. 
1Turn off the connected equipment.
2Press the [Power] button.
A message to confirm that the power needs to be switched off will be displayed.
3Press the [Power] button once more.
The lamp will be extinguished, the Operation Indicator will blink in orange, and the cool-
down process will commence.
The Operation Indicator will change from blinking to being illuminated in orange once the 
cool-down process has been completed. The amount of time required for the cool down is 
approximately 60 seconds (may be longer depending on the ambient temperature).
Point
·Press a different button if the power is not to be switched off. The message will be erased 
after seven seconds if no buttons are pressed (the power will remain on).
·It is also possible to end projection by pressing the [Power] button as explained in proce-
dure #2 for more than one second (will assume the same status as if ending with proce-
dure #3).
·Button operations are not possible when the Operation Indicator is blinking in orange. In 
this event, please wait until full illumination has been attained.
Power
Freeze
A/V MuteE-ZoomR/C ON
OFF3
1524
Enter
Esc
PowerVideo Computer
A/V mute
ResizeEsc Help
Menu
Tracking TrackingSync
Sync
Shift
Keystone
Volume Power
Power
Power OFF?
Please press      Key again
to power off.
Power
Power
Freeze
A/V MuteE-ZoomR/C ON
OFF3
1524
Enter
Esc
PowerVideo Computer
A/V mute
ResizeEsc Help
Menu
Tracking TrackingSync
Sync
Shift
Keystone
Volume Power
Power 
						

							46 - Ending
4After cooling (check that the operation indicator is illuminated in orange), unplug the 
Power Plug from the socket. 
5Set the R/C ON OFF switch to [OFF] when using the remote control.
Point
The batteries are being consumed when the [R/C ON OFF] switch on the remote control 
unit is set at [ON]. Ensure that the [R/C ON OFF] switch on the remote control unit is set to 
[OFF] when not in use.
6Restore the Front Foot if it has been extended.
Steady the projector by hand, and then lift the Foot Adjust Lever with a finger and gently 
lower it into the main Unit.
7Attach the lens cover.
Caution
Do not remove the Power Plug from the socket when the Operation Indicator is blinking in 
orange. Failure to observe this may result in damage to the equipment and will speed up the 
period for replacing the lamp.
Computer
A/V mute
Resize Power
Illuminated in orange Operation Indicator
Power
Freeze
A/V MuteE-ZoomR/C ON
OFF
3
15
24
Enter
Foot adjust lever 
						

							 Adjusting the Projection Position - 47




 
Adjusting the Projection Position
The projector can be adjusted into the following vertical projection positions.
Feet adjustments
Adjust the projection angle of the projector. 
1Lift the Foot Adjust Lever with a finger and raise the front part of the projector.
The Front Foot will protrude.
2Remove your finger from the Foot Adjust Lever, and then let go of the projector.
3Rotate the lower part of the Front Foot to minutely adjust the height.
Point
·There are cases where the screen will be distorted into a trapezoid shape when foot 
adjustments are performed. Adjust the trapezoid distortion with the keystone correction 
function (see page 49
)
·The Front Foot is restored by lifting the Foot Adjust Lever with a finger and lowering the 
projector.
Foot Adjust Lever
Becomes lower
Becomes higher 
						

							48 - Adjusting the Projection Size




 
Adjusting the Projection Size
It is possible to adjust the size of the projection and correct any trapezoid distortion.
Point
A function to resize the screen (see page 56) and an E-Zoom function for enlarging certain 
areas (see page 57) are also available.
Zoom adjustment
1Rotate the Zoom Ring to make the required adjustments (enlargment up to a maximum 
of 1.3x is possible).
The projection distance must also be adjusted when enlarging the screen. (see page 24
)
Becomes larger
Becomes smaller
Zoom Ring