Epson Projector Emp 3500 User Manual

5.
Use a screwdriver, coin, or similar object to loosen the two screws
holding the lamp in position. You cannot remove these screws.
6.
Lift up the handle and pull out the lamp.464 l Maintenance 

7.Gently insert the new lamp by lowering it into position. Make sure
it is inserted securely.
8.Tighten the screws you loosened in step 5.
9.Replace the lamp cover and tighten the cover screws.
Make sure the lamp cover is securely fastened. The projector turns
itself off if the lamp cover is open.
Resetting the lamp timer
After changing the lamp, you need to reset the lamp timer as follows:1.Make sure the projector is turned off.
2.While holding down the projector’s Comp Sync + and Comp
Tracking +...

Troubleshooting
T
his chapter describes the problems indicated by the warning lights
and provides information on how to solve problems with the projector.
It is divided into the following sections:
lProblems with the projector. See this section if the projector is not
working and to find out what the warning lights are indicating.
lProblems with the screen image. See this section if you cannot
project an image or if the screen image is not good.
If you have a problem, check the appropriate section and...

Problems with the Projector
If you have problems with the projector, first turn it off and unplug
the power cord from the wall outlet. Then plug the power cord back in
and turn on the projector. If this does not solve the problem, check the
warning lights at the top of the projector. These lights alert you to
problems with projector operation.
Warning light
ColorStatus
TempRed
LampRedThe projector is hot.
The lamp needs to be replaced. (See “Replacing
the Lamp” in Chapter 4 for instructions.)
Temp and...

The power status light is flashing green and you cannot turn on the
projector.
The lamp is cooling down. Wait until the light changes to orange and
then turn on the projector.
The power status light does not come on.
Turn off the projector, check that the power cable is connected
securely both at the power outlet and the projector, and press the
Power button again.
Projected images get darker or start to deteriorate, or the lamp
warning light is red.
Replace the projector lamp as described on page 44....

The lamp and temperature warning lights are flashing at the same
time.
An abnormality may have occurred in the projector. Turn off the
projector and unplug the power cord from the wall outlet. Then plug
the power cord back in and turn on the projector. If nothing changes,
call the service center.
Warning: Except as specifically explained in this Owners Manual, do not
attempt to service this product yourself
Problems with the Image or Sound
 An image does not appear on the screen.
Check that the power...

and then Monitors; in the Monitors screen, choose Options and make
sure Macintosh Hi-Res Display or another 640 x 480 display is
selected. For supported display settings, see Chapter 6.
If a 640 x 480 display is selected, see Chapter 6 for supported display
settings. You also may need to modify existing presentation files if you
created them for a different resolution. See your software manual for
specific information.
The message NO SIGNAL is displayed.
An image source not connected to the projector is...

Adjust the Brightness and Contrast settings on the Computer Image or
Video Image main menu. If you’re viewing a computer image, also try
adjusting the Comp Tracking and Comp Sync buttons on the
projector’s control panel.
There may be dirt or smears on the lens. Clean the lens as described in
Chapter 4.
The colors of the image are not right.
The color balance may be incorrect. If you’re displaying a computer
image, adjust the red, green, and blue settings in the Computer image
option menu. If you’re...

Technical Specifications
General
Type of display
Size of liquid crystal panels
Resolution
Image size
Projection distance
Remote control range
Internal speaker system
Optical aspect ratio
Zoom ratioLiquid crystal panel, Thin Film
Transistor (TFT)
1.32 inches (33.6 mm)
640 (horizontal)x 480 (vertical)pixels
21 to 300 inches (0.5 to 7 meters)
4 to 40 feet (1.2to 12.3 meters)
33 feet (10 meters)
3 W monaural
4 x 3 (horizontalx vertical)1:1.4
55 

Projector
lamp
Mechanical
ElectricalType
Power
Part number
Height
Width
Depth
Weight
Voltage
Rated frequency
Power
ConsumptionMetal Halide, DC
100 W, 85 V
ELPLP02
5.9 inches (13.7 cm)
11.2 inches (28.3 cm)
15.1 inches (38.2 cm)
14.8 lb (6.7 kg)
100 to 120 VAC and 200 to 240 VAC
50/60 Hz
150 W, 6 W in Sleep mode
ENERGY STAR Compliance
100 to 120 VAC, 1.5 A, 50/60 Hz
200 to 240 VAC, 0.8 A, 50/60 Hz
Operation: 32 to 104° F (0 to 40° C)
Storage: -4 to 140° F (-10 to 60° C)
Operation: 20 to 80% RH,...