Epson Projector Emp 1700 User Manual

							31
Using the Configuration Menu
A
Selecting from the 
top menu
C
Changing the 
selected item
B
Selecting from the 
sub menu
Top menu
Sub menu (Settings) Guide
Select the setting to change
Using the remote controlUsing the control panel
Buttons used
D
Exit 
						

							32
List of FunctionsImage Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each 
image signal.
Sub Menu
Function
Color Mode
You can select the quality of the image to suit your surroundings. sp.15
Brightness
You can adjust the image brightness. 
Contrast
g
You can adjust the difference between light and shade in the images. 
Color Saturation
You can adjust the colour saturation for the images. 
Tint
(Adjustment is only possible when NTSC signals are being input if you use composite video/S-video.)
You can adjust the image tint. 
Sharpness
You can adjust the image sharpness. 
Abs. Color Temp.
You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. When a high value is selected the image 
becomes tinged with blue, when a low value is selected the image becomes tinged with red.
(This item cannot be selected if sRGB
g is selected as the Color Mode setting in the Image menu.)
Color Adjustment
You can make adjustments by choosing one of the following 
Red, Green, Blue: You can adjust the saturation of each colour individually. 
(This item cannot be selected if values for sRGB
g or Customized are selected from Image - Color Mode.) 
R, G, B, C, M, Y: You can adjust the strength of each colour R (red), G (green), B (blue), C (cyan), M (magenta), Y (yellow) individually.
(This item can only be selected when Customized is selected from Image - Color Mode.)
Reset
You can reset all adjustment values for the Image menu functions to their default settings. To return all menu items to their default settings, see 
sp.39
Computer image
Component video
g/Composite video
g/S-video
g 
						

							List of Functions
33
Signal Menu
Items that can be set vary depending on the image signal currently being projected as shown in the following screen shots. Setting details are saved for each 
image signal.
Sub Menu
Function
Auto Setup
You can select whether, when the input signal changes, the image is automatically adjusted to the optimum state (On) or not (Off). sp.48
Tracking
g
You can adjust computer images when vertical stripes appear in the images. sp.48
Sync.
g
You can adjust computer images when flickering, fuzziness, or interference appear in the images. sp.48
Po si t io n
You can adjust the display position up, down, left, and right when a part of the image is missing so that all of the image is projected. 
Progressive
g
(Component video can only be adjusted when 525i/625i signals are being input)
Off: IP conversion is carried out for each field in the screen. This is ideal for viewing images with a large amount of movement.
On: interlace
g (i) signals are converted into progressive
g (p) signals. This is ideal for viewing still images.
Computer Input
You can select the input signal from Computer (Component Video) port. 
If set to Auto the input signal is set automatically according to the connected equipment. 
If colours do not appear correctly when set to Auto, select the appropriate signal according to the connected equipment. 
Video Signal
If set to Auto, video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being 
projected when set to Auto, select the appropriate signal according to the connected equipment.
Resize
You can set the aspect ratio
g for projected images. sp.17
Reset
You can reset all adjustment values on the Signal menu to their default settings, except for Computer Input. 
To return all menu items to their default settings, see sp.39
Computer image
Component video
g
Composite video
g/S-video
g 
						

							List of Functions
34
Settings Menu
Sub Menu
Function
Keystone
You can correct vertical keystone distortion in images. sQuick Start Guide
Auto Keystone
You can correct keystone distortion automatically.
(This item can only be selected when Front is selected from Extended - Projection)
Operation Lock
You can use this to restrict operation of the projectors control panel. sp.29
Po in t e r Sh ap e
You can select the shape of the pointer. sp.18
Pointer 1:  Pointer 2:  Pointer 3:
Brightness Control
You can set the lamp brightness to one of two settings. 
Select Low if the images being projected are too bright such as when projecting images in a dark room or onto a small screen. When Low is 
selected, the amount of electricity consumed and the lamps operating life are changed as follows, and fan rotation noise during projection is 
reduced. Electrical consumption: about a 46 W decrease, lamp life: about 1.5 times longer
Vo l u m e
You can adjust the volume. sQuick Start Guide
EasyMP Audio Out
(EMP-1715/1705 
only)
You can set the audio out method for EasyMP.  The setting is only effective when projecting images with EasyMP.
You can output audio from an external amplifiers built-in speaker by setting this to External. You can output audio from the projectors built-in 
speaker by setting this to Internal.
Reset
You can reset all adjustment values for the Settings menu to their default settings.
To return all menu items to their default settings, see sp.39For EMP-1715/1705 For EMP-1710/1700 
						

							List of Functions
35
Extended Menu
Sub Menu
Function
Display
You can make settings related to the projectors display. 
Messages: You can set whether to display (On) or not display (Off) the source name when you change the input source, the colour mode name when 
you change the colour mode, a message when no image signal is input, and so on. 
Display Background
*: You can set the screen status for when no image signal is available to Black, Blue, or Logo. 
Startup Screen
*: You can set if the startup screen (the image projected when starting the projector) is displayed or not.
A/V Mute
*: You can set the screen displayed during A/V mute as Black, Blue, or Logo.
Users Logo
*
You can change the users logo that is displayed as a background and displayed during A/V Mute. sp.60
Projection
You can set from the following according to the way the projector is setup. sp.53
Front Front/Ceiling Rear Rear/Ceiling
You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
* When set to Front/Ceiling or Rear/Ceiling, you cannot disconnect the power cable immediately because cool down is performed after the 
power is turned off.
* When Users Logo Protect is set to On in Password Protect, settings concerning users logo cannot be changed. You can make changes after setting Users 
Logo Protect to Off. sp.27For EMP-1715/1705 For EMP-1710/1700 
						

							List of Functions
36
Operation
Direct Power On: You can set whether Direct Power On is enabled (On) or disabled (Off). 
When it is set to On and the projector power cable is connected to an electrical outlet, be aware that sudden surges of electricity when power 
comes back on after a power outage may cause the projector to turn on automatically. 
Sleep Mode:
 You can set whether projection stops automatically (On) or not (Off) when no operations are carried out for about 30 minutes while no image 
signals are being input. 
 You can set whether the power turns off automatically (On) or not (Off) after about 30 minutes when the A/V mute slide is closed. 
Sleep mode is set to (Off) at the time of purchase, so do not forget to turn off the power after projecting.
High Altitude Mode: Set to On when using the projector above an altitude of 1500 m.
Standby Mode
(EMP-1715/1705 
only)
You can use network monitoring and control functions while the projector is in standby mode when this is set to Network On. 
You can use SNMP
g to monitor and control the status of the projector over the network, or by using the EMP Monitor software supplied with this 
product.
USB Type B
(EMP-1715/1705 
only)
Set to EasyMP when the projector and a computer are connected by a USB cable and computer images are projected. sWireless LAN Quick 
Connection Guide
Link 21L
You can set whether or not to use EMP Link21L
g utility software. 
(Select it after setting USB Type B to Link 21L.)
Multi-screen
You can adjust the hue and brightness of each projected image when multiple projectors are lined up and projecting. sp.23
Screen ID: When performing Image Correction for Multi-screen by using one remote control for multiple projectors, you can define which 
projector to use when individual IDs are set. 
The IDs set here are only effective during Image Correction for Multi-screen.
Image Correction: You can make the following adjustments.
 Adjustment Level: You can adjust from black to white in five stages called levels 1 to 5, and in each level 1to 5 you can adjust Brightness 
Correct. and Color Correct.
 Brightness Correct.: Corrects the difference in the brightness of each product.
 Color Correct. (G/R) / Color Correct. (B/Y): You can correct the difference in the colour of each product.
Language
You can set the language for message displays. 
Reset
You can reset Display
*1 and Operation
*2, in the Extended menu to their default settings.  
To return all menu items to their default settings, see sp.39
*1 When Users Logo Protect is set to On in Password Protect, settings relating to users logo cannot be changed. You can make changes after setting Users 
Logo Protect to Off. sp.27
*2 Except for High Altitude Mode. 
Sub Menu
Function 
						

							List of Functions
37
Network Menu (EMP-1715/1705 Only)
When Network Protect is set to On in Password Protect, a message is displayed and the settings cannot be changed. You can make changes after 
setting Network Protect to Off. sp.27
Sub Menu
Function
To  N e t w o r k  
Configuration
You can display the network settings screen. sEasyMP Operation Guide Preparing the Projector, Wireless LAN Quick Connection Guide 
						

							List of Functions
38
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items displayed vary depending on the image signal currently 
being projected as shown in the following screen shots.
Sub Menu
Function
Lamp Hours
You can display the cumulative lamp operating time
*.
When it reaches the lamp warning time, the characters are displayed in yellow.
Source
You can display the input port name for the connected equipment currently being projected. 
Input Signal
You can display the content of Computer set in the Signal menu according to the Source. 
Resolution
You can display the input resolution. 
Video Signal
You can display the content of Video Signal set in the Signal menu.
Refresh Rate
g
You can display the refresh rate. 
Sync
g Info
You can display the image signal information. 
This information may be needed if service is required.
* The cumulative use time is displayed as 0H for the first 10 hours. 
Computer image/Component video
g
Composite video
g/S-video
g
EasyMP 
						

							List of Functions
39
Reset Menu
Sub Menu
Function
Reset All
You can reset all items in all menus to their default settings. 
The following items are not reset to their defaults: Computer Input, Users Logo, Multi-screen, all items for Network menus, Lamp Hours, 
and Language. 
Reset Lamp Hours
You can clear the cumulative lamp hours use time, and return it to 0H. Reset when you replace the lamp. 
						

							TroubleshootingThis chapter describes how to identify problems and what to do if a problem is found. Using the Help..................................................... 41
Problem Solving................................................. 42
 Reading the Indicators......................................................42
t Power indicator lights red .......................................................... 43
i · o Indicator is lit or flashing orange......................................... 44
 When the Indicators Provide No Help ............................45
Problems relating to images ........................................................... 46
Problems when projection starts..................................................... 49
Other problems ............................................................................... 50