Epson Projector Elp 3000 User Manual

66
IThe temperature status light is orange.
The projector is overheating and turns the lamp off automatically. Let the
projector cool for a few minutes; then turn it back on. Make sure nothing is
blocking the ventilation vents.
The air filter may be clogged. Clean it as described in Chapter 5 and then let the
projector cool for a while.
If the projector continues to overheat after you clean the air filter, the problem
may be caused by damage to the cooling fan or internal circuits. Contact a
qualified...

Problems with the Image or SoundIAn image does not appear on the screen.
Check that the power light is on and the lens cover is off. Also make sure the
Y-cable is installed correctly to both the image source and projector as described
in Chapter 1.
The projector may be in standby mode. Press the Standby button on the remote
control or operation panel to turn on the lamp.
The correct image source may not be selected. Press the Video button on the
remote control or operation panel to choose the other image...

66
IOnly the test pattern is displayed.
The input source has not been selected correctly. Press the Video button on the
remote control or operation panel to select the other image source.
The projector is not detecting the signal from the source. Check that the cable is
securely attached to both the source and projector If it is, the problem may be
with your presentation software.
The proper order was not followed when the projector and peripheral devices
were turned on. Turn off the projector and all...

IThe colors of the image are not right.The color balance may be incorrect. If you’re displaying a computer image,
adjust the Red, Green, and Blue settings in the Computer menu. If you’re
displaying video, adjust the Color and Tint settings. Check also that Invert in the
Display menu is not selected.
The video cable from your computer may not be properly attached. Check to see
that it is properly and securely attached to the connectors on both the projector
and image source.I
Text is not displayed...

Problems with the Remote Control
70I
You programmed the buttons on the remote control to control the
computer, but pressing one or more buttons has no effect.
First make sure the RS-23X serial cable is properly and securely connected as
described in Chapter 1. Check that the Serial setting on the Options menu is on
and the ELP Remote Programmer is running on your computer.
The remote control is more than 33 feet from the projector or is more than
30 degrees to the side of the projector. Move closer to...

The batteries in the remote control are not inserted properly or are no longer
good. Reinsert them or replace them if necessary.
A strong light source, such as direct sunlight or a compact fluorescent tube, is
causing interference. Move the projector away from the strong fight source.I
Using the trackball has no effect.
The remote control is in sleep mode. Press any button to exit sleep mode so you
can use the trackball.I
Double-clicking a programmable button has no effect.
You are double-clicking too...

Technical Specifications
General
Type of display
Size of liquid
crystal panels
Resolution
Image size
Projection distance
Remote control range
Maximum volume
Thin Film Transistor (TFT)
1.32 inches (33.6 mm)
640 (horizontal) x 480 (vertical) pixels
21 to 300 inches (.5 to 7 meters)
4 to 40 feet (1.2 to 12.3 meters)
33 feet (10 meters)
1W X 1W stereo
73 

74
Optical
Aspect ratio4 x 3 (horizontal x vertical)
Brightness250 lumens maximum
Zoom ratio
1:1.4
Projector Lamp
Model number
Type
Power
MSCRl50E3H
Metal halide
150w
Mechanical
Height
Width
Depth
Weight
5.9 inches (14.9 cm)
11.2 inches (28.5 cm)
16.3 inches (41.3 cm)
17 lb (7.7 kg)
A l Technical Specifications 

Electrical
Voltage
Rated frequency
Fuse type
Power
consumption
l00-120U4C and 220-240VAC
50/60 Hz
25OV, 6.3AT, 5 x 20mm
22OW (in standby mode, 5OW)
l00 - 120 VAC 3.5 Amps, 50/60 Hz
220 - 240 VAC 2.1 Amps, 50/60 Hz
Environmental
TemperatureOperation:41 to 104°F (5 to 40° C)
Storage:14 to 140° F (-20 to 60° C)
HumidityOperation:
20 to 80% RH,
non-condensing
Storage:10 to 90% RH,
non-condensing
Electrical
75 

Computer type
76A l Technical Specifications
Supported Monitor Displays
The projector displays images at a resolution of 640 x 480 pixels. To display a
higher resolution image, the projector compresses it to 640 x 480.
The following table lists the display formats supported by the projector:
FormatsResolutions
IBM PC compatibleVGA, VESA, NEC,640 x 460
JEGA,
CGA640x200
640x400
640x360
720
x360*
720
x400800X600*
Apple Macintosh
l Compressed to 640 x 460.Standard 8- and
24-bit color monitor
640 x 460
640x400