Epson Projector EH-TW9300W User Manual

							Useful Functions
60
Operating the Remote Control
Name Function
aTurns the power for the WirelessHD Transmitter on or off.
bSwitches the output image between a monitor device, such as a television, connected to
the HDMI Out port on the WirelessHD Transmitter and the projector. 
s  p.61
cSwitches the image source for the AV device connected to the WirelessHD Transmitter.
s  p.62
c
Point the remote control towards the WirelessHD Transmitter.
Remote Control Operating Range
The following shows the operating range between the remote control and the WirelessHD Transmitter.
Operating range (left to right)Operating range (top to bottom)
Switching the Input and Output
With the WirelessHD Transmitter, you can connect and switch between up to four multi-media players (input
devices to be played back) and one monitor device (a monitor device displaying an image, such as a television).
Point the remote control at the WirelessHD Transmitter and press its 
 button to switch between input
devices and its 
 button to switch between output devices. 
						

							Useful Functions
61
Switching the target image
You can switch between a monitor device, such as a television, connected to the HDMI Out port on the
WirelessHD Transmitter and the projector.
a
Turn on the projector or the monitor device, such as a television.
b
Turn on the WirelessHD Transmitter.
The On/Standby indicator on the WirelessHD Transmitter turns on.
c
Point the remote control at the WirelessHD Transmitter, and then press the  button
on the remote control or the 
 button on the WirelessHD Transmitter.
Remote control WirelessHD Transmit-
ter
Depending on the output target, the indicators on the WirelessHD Transmitter indicate the following
status. The output target projected last time is projected the next time the projector is turned on.
WiHD indicator On: The image is being output to the projector.
TV indicator On: The image is being output to the monitor device. 
						

							Useful Functions
62
c
You can switch to the other monitor device even when the projector is off.
Switching the image source
Use the  button on the remote control to switch the image source for the AV device connected to the
WirelessHD Transmitter. 
						

							Useful Functions
63
Using the HDMI Link Function
HDMI Link Function
When an AV device that meets the HDMI CEC standards is connected to the projector's HDMI port, you can
perform linked operations such as linked power on and volume adjustment for the AV system from one
remote control. Also, when projecting images in WirelessHD, you can use the HDMI link function (EH-
TW9300W/EH-TW8300W only).
c
•As long as the AV device meets the HDMI CEC standards, you can use the HDMI link function even if
the AV system in-between does not meet the HDMI CEC standards.
•Up to 3 multi-media players that meet the HDMI CEC standards can be connected at the same time.
Connection Example
Projector Amplifier Multi-media players and so on
HDMI Link Settings
When HDMI Link is set to On, you can perform the following
operations. 
s Settings - HDMI Link - HDMI Link  p.80
•Input Change Link
Changes the input source of the projector to HDMI when
content is played back on the connected device.
•Connected Devices Operations
Using the projector's remote control, you can perform op-
erations such as Play, Stop, Fast Forward, Rewind, Next
Chapter, Previous Chapter, Pause, Volume Adjustment, and
Audio Mute.
You can also select the following functions from the HDMI
Link screen.
Function Explanation
Audio Out Device*Selects which device outputs audio.
WiHD Transmitter (Optical): Select this to output audio from the device connected
to the Optical Audio-Out port on the WirelessHD Transmitter. Also select this when
outputting audio from an AV amplifier that supports the HDMI CEC standards.
WiHD Transmitter (HDMI): Select this to output audio from the device connected to
the HDMI Out port on the WirelessHD Transmitter.
Power On Link
When Power On Link is set, operations are linked as shown below.
•When the projector is turned on, the connected devices are also turned on.
•Also, when the connected devices are turned on and content is played back, the projector
turns on. However, the projector does not turn on when connected to the WirelessHD
Transmitter even when the connected device is turned on. 
						

							Useful Functions
64
Function Explanation
Power Off Link
When Power Off Link is set to On, when the projector is turned off, the connected
devices are also turned off.
•This only works when the connected device's CEC power link function is enabled.
•Note that depending on the status of the connected device (for example, if it is record-
ing), the device may not power off.
Link Buffer If HDMI Link is not working correctly, you may be able to improve it by changing the
settings.
*EH-TW9300W/EH-TW8300W only.
c
To use the HDMI Link function, you must configure the connected device. See the documentation
supplied with the connected device for more information.
Connecting
You can check the connected devices that are available for HDMI Link, and select on the device you want to
project the image from. Devices that can be controlled by HDMI Link automatically become the selected
device.
Before displaying the list of connected devices, check that HDMI Link is set to On. 
s Settings - HDMI
Link - HDMI Link  p.80
a
Press the  button, and then select
Device Connections.
The Device Connections list is displayed.
Devices that have an aqua icon to their left
are linked by HDMI Link.
If the device name cannot be determined
this field is left blank.
b
Select the device you want to operate
using the HDMI Link function.
c
•If the cable does not meet the HDMI standards, operations are not possible.
•Some connected devices or functions of those devices may not operate properly even if they meet the
HDMI CEC standards. See the documentation and so on supplied with the connected device for more
information. 
						

							Useful Functions
65
Projecting Two Different Images Using Picture
in Picture
Types of Screen that can be Displayed Simultaneously
Two different image sources can be projected, one in the main
screen (large screen) and the other in the sub screen (small screen).
You can view the sub screen while viewing the main screen.
Combinations of input sources for Picture in Picture projection
HDMI1 HDMI2 WirelessHD*PC LAN
HDMI1
---
HDMI2---
WirelessHD*---
PC-- - --
LAN-- - --
*EH-TW9300W/EH-TW8300W only.
Projecting on a Picture in Picture
Starting and exiting Picture in Picture
Press the  button on the remote control while the projector is projecting.
The currently input image is displayed on a Picture in Picture.
Main screen: The current image
Sub screen: The source different from the main screen
Press the 
 button again to end the Picture in Picture display.
c
•You may not be able to display 3D or 4K images depending on the Picture in Picture requirements.
•You can switch the displays between the main and the sub screen by holding down the  button.
•If the source being input is not supported, nothing is displayed. 
						

							Useful Functions
66
Changing the Picture in Picture settings
Use the Picture in Picture menu to change the size or position of the sub screen.
a
Press the  button on the remote
control while the projector is
projecting.
The Picture in Picture menu is displayed.
b
Make settings for each of the
displayed functions.
Available functions on the Picture in Picture menu
Function Explanation
Subscreen Size
Selects the sub screen size using Small and Large.
Subscreen Position
Changes the sub screen position using Top Right, Bottom Right, Top Left, and Bot‐
tom Left.
Subscreen Source
*Selects which source is displayed as the sub screen.
Swap Main/Sub Switches the main and sub screens.
Exit Picture in Picture Exits the Picture in Picture display.
*EH-TW9300W/EH-TW8300W only. 
						

							Using the Projector on a Network
67
Projecting Using Wired LAN
You can send images to your projector through a wired network.
To do this, connect the projector to your network, and then set up your projector and computer for network
projection.
When using EasyMP Multi PC Projection, you can display up to four separate screens from the projector from
up to 50 computers connected to the network. 
Download EasyMP Multi PC Projection from the following Web site.
http://www.epson.com
Selecting Wired Network Settings
Before you can project from computers on your network, you need to select network settings on the projector.
c
Before making settings, connect a LAN cable to the LAN port, and connect the projector to the wired
LAN.
a
Press the  button to display menus in the order Network - Network Configuration.
b
Select Basic, and then set the following as necessary.
•Projector Name: Enter a name up to 16 alphanumeric characters long to identify the projector over the
network.
•PJLink Password: Set a password to use when you control the projector using compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
•Remote Password: Set a password to use when you operate the projector from a smartphone or a tablet. You
can enter up to 8 single-byte alphanumeric characters.
•Display LAN Info.: Set the display format for the projector's network information.
c
Use the displayed keyboard to enter the name, passwords and keyword. Press the 
 buttons on the remote control to highlight characters, and then press the 
button to enter them.
c
Select Wired LAN, and then press the  button. 
						

							Using the Projector on a Network
68
d
Select the basic options as necessary.
•If your network uses DHCP, set DHCP to On.
•If you are not using DHCP, set DHCP to Off, and then enter the projector's IP Address, Subnet Mask, and
Gateway Address.
e
When you have finished making settings, select Complete and follow the on-screen
instructions to save your settings and exit the menus.
f
Press the  button on the remote control.
The settings are complete when you see the correct IP address on the LAN standby screen.
c
To prevent the IP address from being displayed on the LAN standby screen or the Home screen,
set IP Address Display to Off. 
s Network - Network Configuration - Wired LAN  p.89 
						

							Using the Projector on a Network
69
Projecting Using Wireless LAN
You can project images from smartphones, tablets, and computers over wireless LAN.
To project over wireless LAN, you need to make wireless network settings for the projector and the connected
device in advance.
You can use one of the following methods to project over wireless LAN.
•When using EasyMP Multi PC Projection, you can display up to four separate screens from the projector from up to
50 computers connected to the network. 
Download EasyMP Multi PC Projection from the following Web site.
http://www.epson.com
•When using Epson iProjection, you can project images from smartphones and tablets. s   p.72
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you need to select network settings for the projector.
a
Press the  button to display menus in the order Network - Wireless LAN Power.
b
Use the  buttons to select On, and then press the  button.
c
Select Network Configuration, and then press the  button.