Epson Projector BrightLink 585Wi User Manual

1. Connect one end of the remote control cable to the
SYNC Inport on one projector, and connect the
other end to the SYNC Outport on the other projector.
Note: If you are connecting three or more projectors, connect the projectors in a chain as shown.
2. In the Extended menu, set the Sync of Projectorssetting toWired.
Note: If you are using the projector in the same room as another projector that does not support
cable connection, set the Wired Sync Modesetting toMode 2in the projectors Extended menu....

Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
Caution:Use only the type of batteries specified in this manual. Do not install batteries of different types,
or mix new and old batteries.
1. Open the battery cover.
2. Insert the batteries with the +and –ends facing as shown.
52   

3. Close the battery cover and press it down until it clicks into place.
Warning: Dispose of used batteries according to local regulations. Do not expose batteries to heat
or flame. Keep batteries out of the reach of children; they are choking hazards and are very
dangerous if swallowed.
Parent topic: Setting Up the Projector
Installing Batteries in the Pens Each pen uses one AA battery.
1. Open the battery cover as shown.
53   

2. Insert the battery with the
+and –ends facing as shown.
3. Replace the battery cover and press it down until it clicks into place.
Parent topic: Setting Up the Projector
54   

Using the Projector on a Network
Follow the instructions in these sections to set up your projector for use on a network.
Note:To use the interactive pens with your projected computer image, you need to connect the USB
cable, even if you are projecting through the network.
Wired Network Projection
Wireless Network Projection
Setting Up Projector Network E-Mail Alerts
Setting Up Monitoring Using SNMP
Controlling a Networked Projector Using a Web Browser
Crestron RoomView Support
Wired Network Projection...

Note:
If your projector is connected via a LAN cable to a network that includes a wireless access point,
you can connect to the projector wirelessly through the access point using the EasyMP Network
Projection software.
Connecting to a Wired Network
Selecting Wired Network Settings
Parent topic: Using the Projector on a Network
Related references
Projector Network Settings - Network Menu
Connecting to a Wired Network To connect the projector to a wired local area network (LAN), use a 100Base-TX or...

1. Turn on the projector.
2. Press the
Menubutton.
3. Select the Networkmenu and press Enter.
4. Select Network Configuration and pressEnter.
5. Select the Basicmenu and press Enter.
57 

6. Select the following basic options as necessary:
•Projector Name lets you enter a name up to 16 alphanumeric characters long to identify the
projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric characters long for using the
PJLink protocol for projector control.
• Web Control Password lets you enter a password up to 8 alphanumeric characters long for
accessing the projector over the web. (Default user name is EPSONWEB; default password is
admin.)
• Projector...

• If you must set addresses manually, turn off
DHCPand enter the projectors IP Address,Subnet
Mask, and Gateway Address as needed.
Note: To highlight the numbers you want from the displayed keyboard, press the arrow buttons on
the remote control. To select a highlighted number, press Enter.
10. To prevent display of the IP address on the standby screen, turn off IP Address Display.
11. When you finish selecting settings, select Completeand follow the on-screen instructions to save
your settings and exit...

• Projection from iOS or Android devices with the wireless LAN module and free Epson iProjection app;
visit epson.com/projectorapp (U.S.) orepson.ca/projectorapp (Canada) for more information.
Installing the Wireless LAN Module
Using Quick Wireless Connection (Windows Only)
Selecting Wireless Network Settings Manually
Selecting Wireless Network Settings in Windows
Selecting Wireless Network Settings in OS X
Setting Up Wireless Network Security
Parent topic: Using the Projector on a Network
Related...