Epson Projector 5020UBe User Manual

Using WirelessHD61
Connecting the WirelessHD Transmitter
To prepare your device to work with the WirelessHD button on the remote control, follow 
these steps:
1. Follow the instructions on the previous page and place the transmitter within range of the 
projector.
2. Plug the AC adapter into the transmitter and an electrical outlet.
3. Connect HDMI cables to your video devices and the HDMI ports on the side and back 
of the WirelessHD Transmitter.
Note: You can connect up to five input sources to the...

62Using WirelessHD
Viewing WirelessHD Content
Follow these steps to view WirelessHD content:
1. Turn on the power switch on the side of the transmitter.
2. Turn on your source device and begin playback.
3. Turn on the projector.
4. Press the 
WirelessHD button on the remote control.
Note: If the WirelessHD connection fails, press the Setup button on the bottom of the 
transmitter, then try again.
The WiHD light on the transmitter should light up and your projector should now display 
WirelessHD content....

Using WirelessHD63
Note: Make sure to point the remote at the WirelessHD transmitter.
The sub-screen menu is displayed:
2. Press the 
Input button repeatedly to highlight different input sources.
When you have highlighted the source you want to switch to, stop pressing the 
Input button. 
The display will automatically switch to the selected source after a few seconds. 

64Using WirelessHD
If you have connected a television or other display to the output port on the transmitter and 
want to switch between wired and wireless display modes, press the 
Output button on the 
remote control or transmitter.
Note: The WiHD light on the transmitter will light up when the wireless display mode is active.
Using Picture-in-Picture
If you’ve connected multiple video sources to the WirelessHD Transmitter, you can use the 
Picture-in-Picture (P-in-P) feature to wirelessly project...

Using WirelessHD65
■Press and hold the P-in-P button on the remote control to switch the sources shown 
in the main display and the sub-screen.
3. When you’re finished watching P-in-P, press the 
P-in-P button on the remote control to 
close the sub-screen and resume normal projection. 

66Using HDMI Link
Using HDMI Link
When you connect HDMI CEC-compatible devices to the projector with HDMI cables, you 
can control them using the HDMI Link control buttons on the projector’s remote control. 
This lets you use just one remote control to operate many commonly used features on all your 
devices.
In a typical configuration, your DVD, Blu-Ray or other media player may be connected to 
the projector through an amplifier or home theater system. You can connect up to three 
media players that...

Using HDMI Link67
3. Press the HDMI Link button to exit the menu system.
4. Set up your connected devices so their HDMI CEC-compatible functions are enabled. 
For details, refer to the device manufacturer’s documentation.
Changing HDMI Link Settings
1. Press the HDMI Link button on the projector’s remote control.
2. Select 
Device Connections. You see this screen:
Note: WirelessHD is only available on the PowerLite Home Cinema 5020UBe.
3. Use the u and d arrow buttons to select the device you want to...

68Maintenance
Maintenance
Your projector needs little maintenance. All you need to do on a regular basis is keep the lens 
clean. You also may need to clean the air filter to prevent overheating.
Warning: Before cleaning any part of the projector, turn it off and unplug the power cord. Never 
open any cover on the projector, except as specifically explained in this manual. Dangerous 
electrical voltages in the projector can injure you severely. Do not try to service this product 
yourself, except as...

Maintenance69
Caution: Never rub the lens with abrasive materials. Use only lens cleaning fluids that are designed 
for cleaning optics. Avoid touching the lens with your bare hands to prevent fingerprints on or 
damage to the lens surface.
Cleaning the 3D Glasses
Use the included lint-free cloth (do not use paper towels) to gently wipe the 3D glasses 
whenever you notice dust, dirt, smudges, or fingerprints on the surface.
Caution: Never rub the 3D glasses with abrasive materials. 

70Maintenance
Cleaning the Projector Case
Before you clean the case, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral 
detergent. Then wipe the case and dry it with a dry cloth.
Caution: Never use wax, alcohol, benzene, thinner, or other chemical detergents. These 
can damage the case. Do not use canned air, or the gases may leave a residue. Never...