Epson Projector 5020UB User Manual

Making Detailed Adjustments41
Adjusting the Picture Quality
Before fine-tuning the image using these adjustments, make sure you have already selected the 
best Color Mode for your picture and viewing environment, as described on page 34. Then 
use the settings in this section to finish adjusting the picture to your liking. 
Most image quality settings are saved independently for each input signal type, input source 
(Video, HDMI, WirelessHD, Component, PC), and color mode. After you finish adjusting 
the...

42Making Detailed Adjustments
■Auto Iris
When this setting is on, the light output is automatically adjusted according to the 
brightness of the image. Select either 
Normal or High Speed to indicate how quickly 
you would like the projector to respond to changes in the brightness of the image. The 
setting is stored separately for each image source and color mode.
It is best to use 
High Speed for content that frequently changes from bright to dark 
images. Normal can be used for all other content....

Making Detailed Adjustments43
■Power Consumption
This setting controls the light output from the projector. On Normal, the projector 
produces a brighter image and the lamp uses more power. To save power and extend the 
life of the lamp, select 
ECO.
Sharpness and Picture Quality Settings
If the image looks fuzzy, or if it contains noise or flickering, you can use these settings to 
correct it.
■Sharpness
Use this function to make lines and edges appear more distinct in the image. This setting 
is stored...

44Making Detailed Adjustments
■Motion Detection
This setting specifies how signals are converted to progressive signals. Select a lower 
setting for slow-moving or still images (
S) or select a higher number for video images 
(
M).
Note: This setting can be used only when viewing a composite video signal, or 480i or 576i, or 
1080i signals input through the Component, HDMI1, or HDMI2 ports (see page 89).
■Noise Reduction
Note: This is not be available with a signal input through the PC port.
This setting...

Making Detailed Adjustments45
Color Settings
If the image colors don’t look correct, you can adjust them using these settings. Use the first 
three settings described below to make the most visible changes. If you only need to make 
slight adjustments, you can fine-tune the picture with the remaining settings. Most color 
settings are stored separately for each image source and color mode.
■Color Saturation
Note: This setting cannot be used with a signal input through the PC port.
Adjusts the color...

46Making Detailed Adjustments
■RGBCMY
Use the RGBCMY settings to adjust the hue, saturation, and brightness of the six color 
components (red, green, blue, cyan, magenta, yellow). After adjusting each color, press 
Esc to move to another menu option. You can also access this setting by pressing the 
RGBCMY button on the remote control. See page 37 for more information. 
■Gamma
You can select from five gamma settings (2.0 to 2.4) or customize your own setting from 
your image or a displayed graph. Lower...

Making Detailed Adjustments47
■3D Format
Use this setting to select the 3D format supported by your video device. In most cases, the 
projector will correctly detect the 3D format when this option is set to 
Auto. You should 
only select the 
2D, Side by Side, or Top and Bottom formats when your projector 
doesn’t properly display 3D images. See your video source documentation for 
information on which mode to select.
■3D Depth
Adjust the slider to change the depth of the 3D effect.
■3D Brightness...

48Making Detailed Adjustments
Adjustments for Computer Images
In addition to the settings described previously, you can adjust the Tracking and Sync settings 
for analog RGB computer images. Normally, these settings are adjusted automatically by the 
projector. If you notice that the image is blurry or contains dark vertical bands, you may need 
to adjust the settings yourself.
■Auto Setup
Leave this setting on so that the projector automatically adjusts the tracking, sync, and 
position of the image....

Making Detailed Adjustments49
WirelessHD Settings (PowerLite Home Cinema 5020UBe 
only)
Use these options to manage the WirelessHD connection and access the WirelessHD 
reception monitor.
■Device Connections
Select this option to display a list of available WirelessHD devices.
Note: The MAC Address of the included WirelessHD Transmitter can be found on the bottom 
of the transmitter.
Use the arrow keys to navigate the menu and press Enter to select a device. 
■WirelessHD
Enables or disables the...

50Making Detailed Adjustments
Split Screen Setup
Press the Menu button while in Split Screen mode to access this menu.
■Screen Size
Adjusts the size of the two screens. Choose 
Larger Left to increase the size of the left 
screen, 
Larger Right to increase the size of the right screen, or Equal to split the display 
evenly between the two screens.
Note: Depending on the source and resolution of each input, the two screens may not appear 
to be of equal size when the Equal option is selected.
■Source...