Epson Projector 1705cuser Manual

Presenting Through a Wireless Network61
5. Check your wireless card’s or adapter’s device settings. 
(Depending on the type of card or adapter you’re using, some of 
the settings may be different than those listed here.)
■Set the Network Type to Infrastructure. 
■Set the SSID to match the name assigned to the access point 
(which should also be the projector’s ESSID). 
■Make sure Encryption is Disabled if you have not set up 
encryption on the projector. 
6. Click the 
General tab and make sure that your...

62Presenting Through a Wireless Network9. Select 
Internet Protocol and click the Properties button. You 
see this screen:
10. If your access point uses DHCP, select 
Obtain an IP address 
automatically
. Otherwise select Use the following IP address 
and enter the required information: 
■IP address: Type in the IP address you want to assign to the 
computer. It must be formatted like other addresses on the 
network. The last section must be unique.
■Subnet mask: For example: 255.255.255.000, but this...

Presenting Through a Wireless Network63
You see a screen like this:
13. Verify that you’ve enabled your computer’s connection to the 
access point. It should be listed with the small  icon next to it, 
indicating a connection. 
If it’s not listed, click 
Configure and type the name of your access 
point. 
14. When you’re done making settings, click 
OK to close the dialog 
box. 
Now you’re ready to connect to the projector. See “Projecting Over a 
Network” on page 73.  

64Presenting Through a Wireless Network
Checking the Gateway IP Address on Windows
If you’re entering IP addresses manually and need to find out the 
gateway IP address (the IP address of your access point), make sure the 
wireless connection to the access point is currently active, as described 
in the previous section. Then follow these steps:
1. Access your wireless network Properties window. For example, in 
Windows XP you would click 
Start > Control Panel > Network 
and Internet Connections
. Then...

Presenting Through a Wireless Network65
3. Click the Support tab. The gateway’s IP address is listed as 
shown: 
Setting Up Your Mac for Access Point Mode
Your AirPort software is automatically configured to allow your Mac 
to detect Access Point networks. 
Typically, you only need to select your AirPort network name from 
the AirPort status menu on the Mac menu bar. If you’re having 
problems connecting to the projector, follow these steps:
1. From the Apple pull-down menu, select 
System Preferences....

66Presenting Through a Wireless Network3. Make sure Location is set to 
Automatic.
4. Select 
Network Port Configurations in the Show pull-down 
menu.
5. Under Port Configurations, select 
AirPort.
6. Click 
Apply Now. Then close the window.
7. Start the AirPort Admin utility. Select your base station, then 
click 
Configure.
8. On the AirPort tab, make sure your AirPort network name 
matches your projector’s ESSID. If not, enter the projector’s 
ESSID in the AirPort Network text box and click 
Update....

Presenting Through a Wireless Network67
10. Click the AirPort icon on the menu bar at the top of the 
Macintosh desktop. You see the AirPort status menu:
11. Check to make sure AirPort is turned on.
12. Select the name of your AirPort network. 
Using Wireless Security Options 
You can use the following security options when connecting to the 
projector wirelessly: WEP encryption, WPA security, EAP-TLS 
certificate validation, or LEAP, EAP, or PEAP authentication. To set 
these security features up on...

68Presenting Through a Wireless NetworkYou see the following screen: 
4. Press 
Enter to show the menu, then highlight WEP and press 
Enter. 
5. For the WEP encryption setting, highlight 
128 Bit or 64 Bit and 
press Enter. 
6. For Format, highlight 
HEX to enable hexadecimal input or ASCII 
to enable text input, then press 
Enter. 
7. If you chose 
64 Bit, choose Key ID 1, 2, 3, or 4. 
Highlight the 
Encryption key text box and press Enter. Press the 
pointer button to select individual letters; then...

Presenting Through a Wireless Network69
8. Check with your network administrator for directions on entering 
a key for your network, and follow these general guidelines:
■For 128 bit WEP encryption with hexadecimal input, enter 
26 characters, from 0 to 9 and from A to F.
■For 64 bit WEP encryption with hexadecimal input, enter 10 
characters, from 0 to 9 and from A to F. 
■For 128 bit WEP encryption with ASCII or text input, enter 
13 alphanumeric characters.
■For 64 bit WEP encryption with ASCII or...

70Presenting Through a Wireless Network4. Press 
Enter to show the menu, then choose WPA-PSK (TKIP) or 
WPA-PSK (AES) and press Enter. 
Highlight the 
PSK (pre-shared key) text box and press Enter. 
Press the  pointer button to select individual letters; then press 
Enter to input a character. To add a blank space or to navigate 
backward and forward through the input text, highlight the 
arrows and press 
Enter. To toggle symbol settings or capital 
letters, highlight the option and press 
Enter. When...