Epson Powerlite S7 Multimedia Projector Users Guide

Maintaining the Projector71
You can remove the air filter to clean both sides
If the filter is too dirty or broken, replace the filter as described below. 
Replacing the Air Filter
You need to replace the air filter if:
■You cannot remove the dust from it
■The air filter is damaged or torn
■You repeatedly see a projected message telling you to clean or 
replace it
Contact your dealer or call Epson at 800-GO-EPSON 
(800-463-7766) to obtain a new air filter. Request part number 
V13H134A25.
1. Turn off the...

72Maintaining the Projector4. Slide the new air filter into the slot until it clicks into place.
Replacing the Lamp
The life span of the projection lamp is about 4000 hours if Power 
Consumption 
in the Settings menu is Normal (default), and 5000 
hours if this setting is 
ECO. See page 75 to check the lamp usage.
It is time to replace the lamp when: 
■The projected image gets darker or starts to deteriorate.
■The message Replace the lamp appears on the screen and the 
Lamp light flashes orange. To...

Maintaining the Projector73
Contact your dealer or call Epson at 800-GO-EPSON 
(800-463-7766). Request part number V13H010L54.
Follow these steps to replace the lamp:
1. Turn off the projector and unplug the power cord.
2. Let the projector cool for at least an hour (if it has been on). The 
lamp is extremely hot immediately after use. 
3. Loosen the lamp cover screw (you cannot remove it). Then slide 
the lamp cover off.
4. Loosen the two screws holding the lamp in place (you can’t 
remove...

74Maintaining the Projector5. Hold the lamp as shown and pull it straight out.
 
6. Gently insert the new lamp. (If it doesn’t fit easily, make sure it is 
facing the right way.) Then tighten its screws.
7. Replace the lamp cover, then tighten its screw.
8. Reset the lamp timer as described in the next section. 
note
The lamp(s) in this 
product contain mercury. 
Please consult your state and 
local regulations regarding 
disposal or recycling. Do not 
put in the trash.
note
Tighten the lamp cover...

Maintaining the Projector75
Resetting the Lamp Timer
After you replace the lamp, you need to reset the lamp timer using the 
projector’s menu system. 
1. Press the 
Menu button on the remote control or on the 
projector’s control panel. You see the main menu.
2. Select the 
Reset menu and press Enter. You see this screen:
3. Select 
Reset Lamp Hours and press Enter. 
4. When you see the prompt, select
 Yes and press Enter.
5. When you’re finished, press 
Menu to exit.
Checking Lamp Usage 
To check the...

76Maintaining the ProjectorThe life span of the lamp is about 4000 hours if 
Power 
Consumption
 in the Settings menu is Normal (default), and 5000 
hours if this setting is 
ECO. Make sure you have a spare lamp handy if 
the usage hours on this menu are close to the life span of your lamp.
Replacing the Remote Control Batteries
Replace the batteries in the remote as described below: 
1. Turn the remote control over.
2. Press in on the catch on the battery cover as you lift the cover off.
3. Install two...

Maintaining the Projector77
4. Replace the battery cover and press it down until it clicks into 
place.
Transporting the Projector
The projector contains many glass and precision parts. When 
hand-carrying the projector, use the carrying case.
Follow these guidelines to prevent damage when transporting it: 
■Close the A/V Mute slide (lens cover).
■If a USB device is connected, remove it from the projector.
■Return the projector feet to their stored (highest) positions.
■When shipping the projector for...

78Maintaining the Projector 

79
6
Solving Problems
This chapter helps you solve problems with your projector and tells 
you how to contact technical support for problems you can’t solve 
yourself. The following information is included:
■Using the projector’s on-screen help system
■What to do when the projector’s status lights flash
■Solving projector operation problems
■Solving problems with the image or sound
■Solving problems with the remote control
■Contacting technical support 

80Solving Problems
Using On-Screen Help
If the image doesn’t look right or your audio isn’t working, you can 
get help by pressing the 
? Help button on the projector or the remote 
control.
1. Press the 
? Help button on the remote control or on the 
projector. You see the Help menu:
2. Use the arrow buttons on the remote control or the projector to 
highlight menu items.
3. Press the 
Enter button on the remote control or the projector to 
select the menu item and read the solutions. 
4. To exit the...