Epson Powerlite S7 Multimedia Projector Users Guide

Fine-Tuning the Projector61
■Projection 
Select Front (to project onto the front of a screen), Front/Ceiling 
(when the projector is mounted upside-down from the ceiling), 
Rear (to project from behind onto a transparent screen), or 
Rear/Ceiling (to project from behind onto a transparent screen 
when the projector is mounted upside-down from the ceiling).
■Operation
Direct Power On:
 Enable if you want to be able to start the 
projector when you connect the power cord (without pressing the
 
Ppower...

62Fine-Tuning the Projector
■Link 21L
Select On to enable the projector to be monitored and controlled 
from a computer using Link 21L software and the Epson USB 
Communication driver.
■Language 
Select a language to use for the projector menus.
Using the Projector Security Features
To prevent unauthorized use of the projector, you can:
■Assign a password. You can use the password to prevent the 
projector from being turned on and prevent your custom startup 
screen from being changed. See the next...

Fine-Tuning the Projector63
Enabling Password Protection
The default setting for the password is 0000. Follow these steps to 
create a new password:
1. Press the 
Freeze button on the remote control for five to seven 
seconds. You see this screen:
2. Select the type(s) of password protection you want to use:
■Power On Protect: Prevents unauthorized use of the 
projector. After the projector is plugged in and turned on, 
you must enter a password to use the projector. Select 
On, 
press 
Enter, then press...

64Fine-Tuning the Projector
Starting the Projector With a Password
When the password function is enabled, you see this screen when you 
plug in and turn on the projector:
Hold down the 
Num button and use the numeric keypad to enter the 
four digit password.
The password screen closes and projection begins.
If projection does not begin, check the following:
■If the password is not correct, you see a message prompting you to 
re-enter the password. If you enter an incorrect password three 
times in...

Fine-Tuning the Projector65
Creating Your Own Startup Screen
You can transfer any image from your computer or video source to the 
projector and then use it as your startup screen. You can also use it as 
the screen displayed when the projector is not receiving a signal or 
when you press the 
A/V Mute button. The image can be a company 
logo, slogan, photograph, or any other image you want to use. 
Capturing the Image
Start by displaying the image you want to use from either a computer 
or video source,...

66Fine-Tuning the Projector7. When the message 
Save this image as the User’s Logo? 
appears, select 
Yes and press Enter. Saving the logo may take a 
few moments. Do not use your projector, remote control, or 
video source while the logo is being saved.
8. When you see the message 
Completed, press Menu to exit. 
Choosing When to Display the Image
After your image is saved, you can set it to display as the startup 
screen, the screen you see when there’s no signal, or the screen you see 
when you press...

Fine-Tuning the Projector67
3. Select Full Lock (to lock all projector buttons) or Partial Lock (to 
lock all buttons except the Ppower button) and press 
Enter.
4. Select 
Yes and press Enter to confirm the setting.
5. Press the 
Menu button to exit. 
To disable the Control Panel Lock function, select 
Off in the Control 
Panel Lock menu. Or press and hold the 
Enter button on the 
projector’s control panel for seven seconds. A message is displayed and 
the lock is released.
Using Security Locking
The...

68Fine-Tuning the Projector 

69
5
Maintaining the Projector
Your projector needs little maintenance. All you have to do on a 
regular basis is clean the lens, and check that the air filter and vents are 
clean. A clogged air filter or vent can block ventilation needed to cool 
the projector.
The only parts you should replace are the lamp and air filter. If any 
other part needs replacing, contact your dealer or a qualified servicer.
This chapter covers the following:
■Cleaning the lens
■Cleaning the projector case
■Cleaning the air...

70Maintaining the Projector
Cleaning the Lens
Clean the lens whenever you notice dirt or dust on the surface.
To remove dirt or smears on the lens, use a commercially available 
cloth for cleaning glasses.
Cleaning the Projector Case
Before cleaning, turn off the projector and unplug the power cord.
■To remove dirt or dust, wipe the case with a soft, dry, lint-free 
cloth.
■To remove stubborn dirt or stains, moisten a soft cloth with water 
and a neutral detergent and firmly wring the cloth dry. Then...