Epson Powerlite Pro G5550nl Users Guide

Using the Projector on a Network101
4. Turn on the SNMP setting.
5. Enter up to two IP addresses for notification.
You can enter a number from 0 to 255 in each field of the address. 
However, the following IP addresses cannot be used: 127.x.x.x, 
224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 
255).
6. For 
Priority Gateway, select Wired or Wireless.
7. If your network environment uses an AMX controller, select 
On 
to allow the projector to be detected by AMX Device Discovery.
8. When...

102Using the Projector on a Network4. Select one of the menu options listed on the screen, then change 
any of the settings as needed. These settings correspond to those 
found in the projector’s menu system.
You cannot change the following settings using a web browser:
■Quick Corner, Pointer Shape, Test Pattern, or User 
Button 
in the Settings menu
■User’s Logo, High Altitude Mode, BNC Sync 
Termination
, Remote Control Type, and Language in the 
Extended menu
■Any settings in the Reset menu
■Any...

Using the Projector on a Network103
From the Projector Control menu, select Web Remote. You see the 
following screen:
■The Power button turns the projector on and off.
■The Search button searches for signal sources (see page 56).
■The Computer button changes the input source to Computer1 
(PowerLite G5450WUNL/G5750WUNL) or, with the 
PowerLite G5550NL/G5650WNL/G5950NL, selects a 
computer signal (connected to the 
Computer1 or Computer2 
port).
■The Video button selects a video signal (connected to the...

104Using the Projector on a Network
■The A/V Mute button temporarily turns off the picture and 
sound (see page 67).
■The Pause button stops the image (see page 67).
■The Volume buttons raise or lower the volume.
■The Page-up/down buttons change slides when you project a 
slideshow over a network or from a device connected to the   
USB port.
■The CC (Closed Captioning) button lets you display closed 
captioning for content that provides it.
Using Crestron RoomView to Monitor 
and Control the Projector...

Using the Projector on a Network105
3. Choose Others and press Enter. You see the following screen:
4. Turn on the 
RoomView setting.
5. Highlight the 
Return button at the top of the screen, then press 
Enter. Choose Setup complete and press Enter, then choose 
Yes and press Enter to save the changes.
6. Press 
Menu to exit.
7. Turn the projector off and then on again. The setting change will 
take effect once the projector restarts.
Using a Browser to Control the Projector
You can use a standard web...

106Using the Projector on a Network2. Open your web browser and enter the IP address of the projector 
you want to monitor in the browser’s address box. You see a 
window like this:
3. Select options on the screen as necessary:
■To turn the projector on or off, click the Power button.
■To raise or lower the volume, click the Vol+ and Vol- 
buttons.
■To temporarily turn off the picture and sound, click the A/V 
Mute
 button (see page 67).
■To select an input source, click it in the Sources List. To...

Using the Projector on a Network107
■To adjust the image sharpness, click the Sharpness button 
in the toolbar.
■To enlarge the image without changing the projection size, 
click the 
Zoom button in the toolbar. Then click the  
button to enlarge the image or the   button to reduce an 
image that was enlarged with the 
 button. Click the arrow 
buttons the change the position of an enlarged image.
4. Use the following buttons in place of the buttons on the 
projector’s remote control:
Additionally, the...

108Using the Projector on a Network
Using the Tools Tab
Select the Tools tab in the top right corner of the window to display 
the window shown below:
1. Enter settings for Crestron
® central controllers in the Crestron 
Control
 section of the window.
2. Enter settings in the 
Projector section of the window:
■Enter a Projector Name to differentiate the current 
projector from other projectors on the network (up to 15 
single-byte alphanumeric characters).
■Enter a Location name for the projector (up to...

Using the Projector on a Network109
4. To require a password for access to the initial Crestron 
RoomView window, click 
Enable in the User Password section 
of the window, enter a password (in both the 
New Password 
and 
Confirm boxes), and click Send.
5. To require a password for access to the 
Tools tab, click Enable in 
the 
Admin Password section of the window, enter a password 
(in both the 
New Password and Confirm boxes), and click 
Send.
6. When you’re through making settings on the 
Tools tab,...

110Using the Projector on a Network